[PATCH 3/3] arm: dts: sun6i: a31s: fix: bpi-m2: add missing regulators
Philipp Rossak
embed3d at gmail.com
Fri Feb 9 09:52:36 PST 2018
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
Signed-off-by: Philipp Rossak <embed3d at gmail.com>
---
arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 56 ++++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
index 51e6f1d21c32..01fcfe0649ad 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
+++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
@@ -99,6 +99,7 @@
pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>;
phy = <&phy1>;
phy-mode = "rgmii";
+ phy-supply = <®_dldo1>;
snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
snps,reset-active-low;
snps,reset-delays-us = <0 10000 30000>;
@@ -193,7 +194,28 @@
#include "axp22x.dtsi"
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-gmac";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
®_dc5ldo {
+ regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd-cpus";
@@ -233,6 +255,40 @@
regulator-name = "vcc-dram";
};
+®_dldo1 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-mac";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pb";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vdd-csi";
+ status = "okay";
+};
+
+®_ldo_io1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pm-cpus";
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
--
2.11.0
More information about the linux-arm-kernel
mailing list