[linux-sunxi] [PATCH 2/3] arm64: allwinner: h6: add device tree nodes for MMC controllers

[Icenowy Zheng]

于 2018年4月27日 GMT+08:00 上午12:45:38, Andre Przywara <andre.przywara at arm.com> 写到:
>Hi,
>
>On 26/04/18 15:07, Icenowy Zheng wrote:
>> The Allwinner H6 SoC have 3 MMC controllers.
>> 
>> Add device tree nodes for them.
>> 
>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>> ---
>>  arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 56
>++++++++++++++++++++++++++++
>>  1 file changed, 56 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
>b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
>> index 4debc3962830..3cbfc035c979 100644
>> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
>> @@ -124,12 +124,68 @@
>>  			interrupt-controller;
>>  			#interrupt-cells = <3>;
>>  
>> +			mmc0_pins: mmc0-pins {
>> +				pins = "PF0", "PF1", "PF2", "PF3",
>> +				       "PF4", "PF5";
>> +				function = "mmc0";
>> +				drive-strength = <30>;
>> +				bias-pull-up;
>> +			};
>> +
>> +			mmc2_pins: mmc2-pins {
>> +				pins = "PC1", "PC4", "PC5", "PC6",
>> +				       "PC7", "PC8", "PC9", "PC10",
>> +				       "PC11", "PC12", "PC13", "PC14";
>> +				function = "mmc2";
>> +				drive-strength = <30>;
>> +				bias-pull-up;
>> +			};
>> +
>>  			uart0_ph_pins: uart0-ph {
>>  				pins = "PH0", "PH1";
>>  				function = "uart0";
>>  			};
>>  		};
>>  
>> +		mmc0: mmc at 4020000 {
>> +			compatible = "allwinner,sun50i-h6-mmc";
>
>This should be:
>			compatible = "allwinner,sun50i-h6-mmc",
>				     "allwinner,sun50i-a64-mmc";

I'm intended to not add A64 compatible, as
H6 is a quite new design
(new process) and there might be different behavior, even on mmc0/1.

>
>> +			reg = <0x04020000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC0>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		mmc1: mmc at 4021000 {
>> +			compatible = "allwinner,sun50i-h6-mmc";
>
>same here
>
>> +			reg = <0x04021000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC1>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> +		mmc2: mmc at 4022000 {
>> +			compatible = "allwinner,sun50i-h6-emmc";
>
>and here:
>			compatible = "allwinner,sun50i-h6-emmc",
>				     "allwinner,sun50i-a64-emmc";

MMC2 on H6 has EMCE capability, so surely there should
only be H6 compatible, and no A64 one.

>
>The rest looks correct to me.
>
>Cheers,
>Andre.
>
>> +			reg = <0x04022000 0x1000>;
>> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
>> +			clock-names = "ahb", "mmc";
>> +			resets = <&ccu RST_BUS_MMC2>;
>> +			reset-names = "ahb";
>> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>>  		uart0: serial at 5000000 {
>>  			compatible = "snps,dw-apb-uart";
>>  			reg = <0x05000000 0x400>;
>>