[PATCH 06/12] usb: mtu3: use FORCE/RG_IDDIG to implement manual DRD switch
Chunfeng Yun
chunfeng.yun at mediatek.com
Wed Sep 27 17:17:14 PDT 2017
In order to keep manual DRD switch independent on IDDIG interrupt,
make use of FORCE/RG_IDDIG instead of IDDIG EINT interrupt to
implement manual DRD switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
---
drivers/usb/mtu3/mtu3.h | 18 ++++++++----
drivers/usb/mtu3/mtu3_dr.c | 61 +++++++++++++++++++++++++++++----------
drivers/usb/mtu3/mtu3_dr.h | 6 ++++
drivers/usb/mtu3/mtu3_host.c | 5 ++++
drivers/usb/mtu3/mtu3_hw_regs.h | 2 ++
drivers/usb/mtu3/mtu3_plat.c | 38 ++----------------------
6 files changed, 74 insertions(+), 56 deletions(-)
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
index ef2dc92..b0c2b5d 100644
--- a/drivers/usb/mtu3/mtu3.h
+++ b/drivers/usb/mtu3/mtu3.h
@@ -115,6 +115,19 @@ enum mtu3_g_ep0_state {
};
/**
+ * MTU3_DR_FORCE_NONE: automatically switch host and periperal mode
+ * by IDPIN signal.
+ * MTU3_DR_FORCE_HOST: force to enter host mode and override OTG
+ * IDPIN signal.
+ * MTU3_DR_FORCE_DEVICE: force to enter peripheral mode.
+ */
+enum mtu3_dr_force_mode {
+ MTU3_DR_FORCE_NONE = 0,
+ MTU3_DR_FORCE_HOST,
+ MTU3_DR_FORCE_DEVICE,
+};
+
+/**
* @base: the base address of fifo
* @limit: the bitmap size in bits
* @bitmap: fifo bitmap in unit of @MTU3_EP_FIFO_UNIT
@@ -196,7 +209,6 @@ struct mtu3_gpd_ring {
* xHCI driver initialization, it's necessary for system bootup
* as device.
* @is_u3_drd: whether port0 supports usb3.0 dual-role device or not
-* @id_*: used to maually switch between host and device modes by idpin
* @manual_drd_enabled: it's true when supports dual-role device by debugfs
* to switch host/device modes depending on user input.
*/
@@ -207,10 +219,6 @@ struct otg_switch_mtk {
struct notifier_block id_nb;
struct delayed_work extcon_reg_dwork;
bool is_u3_drd;
- /* dual-role switch by debugfs */
- struct pinctrl *id_pinctrl;
- struct pinctrl_state *id_float;
- struct pinctrl_state *id_ground;
bool manual_drd_enabled;
};
diff --git a/drivers/usb/mtu3/mtu3_dr.c b/drivers/usb/mtu3/mtu3_dr.c
index 5602561..ec442cd 100644
--- a/drivers/usb/mtu3/mtu3_dr.c
+++ b/drivers/usb/mtu3/mtu3_dr.c
@@ -261,21 +261,22 @@ static void extcon_register_dwork(struct work_struct *work)
* depending on user input.
* This is useful in special cases, such as uses TYPE-A receptacle but also
* wants to support dual-role mode.
- * It generates cable state changes by pulling up/down IDPIN and
- * notifies driver to switch mode by "extcon-usb-gpio".
- * NOTE: when use MICRO receptacle, should not enable this interface.
*/
static void ssusb_mode_manual_switch(struct ssusb_mtk *ssusb, int to_host)
{
struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
- if (to_host)
- pinctrl_select_state(otg_sx->id_pinctrl, otg_sx->id_ground);
- else
- pinctrl_select_state(otg_sx->id_pinctrl, otg_sx->id_float);
+ if (to_host) {
+ ssusb_set_force_mode(ssusb, MTU3_DR_FORCE_HOST);
+ ssusb_set_mailbox(otg_sx, MTU3_VBUS_OFF);
+ ssusb_set_mailbox(otg_sx, MTU3_ID_GROUND);
+ } else {
+ ssusb_set_force_mode(ssusb, MTU3_DR_FORCE_DEVICE);
+ ssusb_set_mailbox(otg_sx, MTU3_ID_FLOAT);
+ ssusb_set_mailbox(otg_sx, MTU3_VBUS_VALID);
+ }
}
-
static int ssusb_mode_show(struct seq_file *sf, void *unused)
{
struct ssusb_mtk *ssusb = sf->private;
@@ -388,17 +389,45 @@ static void ssusb_debugfs_exit(struct ssusb_mtk *ssusb)
debugfs_remove_recursive(ssusb->dbgfs_root);
}
+void ssusb_set_force_mode(struct ssusb_mtk *ssusb,
+ enum mtu3_dr_force_mode mode)
+{
+ u32 value;
+
+ value = mtu3_readl(ssusb->ippc_base, SSUSB_U2_CTRL(0));
+ switch (mode) {
+ case MTU3_DR_FORCE_DEVICE:
+ value |= SSUSB_U2_PORT_FORCE_IDDIG | SSUSB_U2_PORT_RG_IDDIG;
+ break;
+ case MTU3_DR_FORCE_HOST:
+ value |= SSUSB_U2_PORT_FORCE_IDDIG;
+ value &= ~SSUSB_U2_PORT_RG_IDDIG;
+ break;
+ case MTU3_DR_FORCE_NONE:
+ value &= ~(SSUSB_U2_PORT_FORCE_IDDIG | SSUSB_U2_PORT_RG_IDDIG);
+ break;
+ default:
+ return;
+ }
+ mtu3_writel(ssusb->ippc_base, SSUSB_U2_CTRL(0), value);
+}
+
int ssusb_otg_switch_init(struct ssusb_mtk *ssusb)
{
struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
- INIT_DELAYED_WORK(&otg_sx->extcon_reg_dwork, extcon_register_dwork);
-
- if (otg_sx->manual_drd_enabled)
+ if (otg_sx->manual_drd_enabled) {
ssusb_debugfs_init(ssusb);
-
- /* It is enough to delay 1s for waiting for host initialization */
- schedule_delayed_work(&otg_sx->extcon_reg_dwork, HZ);
+ } else {
+ INIT_DELAYED_WORK(&otg_sx->extcon_reg_dwork,
+ extcon_register_dwork);
+
+ /*
+ * It is enough to delay 1s for waiting for
+ * host initialization
+ */
+ schedule_delayed_work(&otg_sx->extcon_reg_dwork, HZ);
+ }
return 0;
}
@@ -407,8 +436,8 @@ void ssusb_otg_switch_exit(struct ssusb_mtk *ssusb)
{
struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
- cancel_delayed_work(&otg_sx->extcon_reg_dwork);
-
if (otg_sx->manual_drd_enabled)
ssusb_debugfs_exit(ssusb);
+ else
+ cancel_delayed_work(&otg_sx->extcon_reg_dwork);
}
diff --git a/drivers/usb/mtu3/mtu3_dr.h b/drivers/usb/mtu3/mtu3_dr.h
index 9b228b5..0f0cbac 100644
--- a/drivers/usb/mtu3/mtu3_dr.h
+++ b/drivers/usb/mtu3/mtu3_dr.h
@@ -87,6 +87,8 @@ static inline void ssusb_gadget_exit(struct ssusb_mtk *ssusb)
int ssusb_otg_switch_init(struct ssusb_mtk *ssusb);
void ssusb_otg_switch_exit(struct ssusb_mtk *ssusb);
int ssusb_set_vbus(struct otg_switch_mtk *otg_sx, int is_on);
+void ssusb_set_force_mode(struct ssusb_mtk *ssusb,
+ enum mtu3_dr_force_mode mode);
#else
@@ -103,6 +105,10 @@ static inline int ssusb_set_vbus(struct otg_switch_mtk *otg_sx, int is_on)
return 0;
}
+static inline void
+ssusb_set_force_mode(struct ssusb_mtk *ssusb, enum mtu3_dr_force_mode mode)
+{}
+
#endif
#endif /* _MTU3_DR_H_ */
diff --git a/drivers/usb/mtu3/mtu3_host.c b/drivers/usb/mtu3/mtu3_host.c
index edcc591..ec76b86 100644
--- a/drivers/usb/mtu3/mtu3_host.c
+++ b/drivers/usb/mtu3/mtu3_host.c
@@ -189,6 +189,8 @@ int ssusb_host_disable(struct ssusb_mtk *ssusb, bool suspend)
static void ssusb_host_setup(struct ssusb_mtk *ssusb)
{
+ struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
+
host_ports_num_get(ssusb);
/*
@@ -197,6 +199,9 @@ static void ssusb_host_setup(struct ssusb_mtk *ssusb)
*/
ssusb_host_enable(ssusb);
+ if (otg_sx->manual_drd_enabled)
+ ssusb_set_force_mode(ssusb, MTU3_DR_FORCE_HOST);
+
/* if port0 supports dual-role, works as host mode by default */
ssusb_set_vbus(&ssusb->otg_switch, 1);
}
diff --git a/drivers/usb/mtu3/mtu3_hw_regs.h b/drivers/usb/mtu3/mtu3_hw_regs.h
index b605975..a7e35f6 100644
--- a/drivers/usb/mtu3/mtu3_hw_regs.h
+++ b/drivers/usb/mtu3/mtu3_hw_regs.h
@@ -472,6 +472,8 @@
#define SSUSB_U3_PORT_DIS BIT(0)
/* U3D_SSUSB_U2_CTRL_0P */
+#define SSUSB_U2_PORT_RG_IDDIG BIT(12)
+#define SSUSB_U2_PORT_FORCE_IDDIG BIT(11)
#define SSUSB_U2_PORT_VBUSVALID BIT(9)
#define SSUSB_U2_PORT_OTG_SEL BIT(7)
#define SSUSB_U2_PORT_HOST BIT(2)
diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c
index fb89920..1e473b0 100644
--- a/drivers/usb/mtu3/mtu3_plat.c
+++ b/drivers/usb/mtu3/mtu3_plat.c
@@ -21,7 +21,6 @@
#include <linux/module.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
-#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include "mtu3.h"
@@ -212,33 +211,6 @@ static void ssusb_ip_sw_reset(struct ssusb_mtk *ssusb)
mtu3_clrbits(ssusb->ippc_base, U3D_SSUSB_IP_PW_CTRL0, SSUSB_IP_SW_RST);
}
-static int get_iddig_pinctrl(struct ssusb_mtk *ssusb)
-{
- struct otg_switch_mtk *otg_sx = &ssusb->otg_switch;
-
- otg_sx->id_pinctrl = devm_pinctrl_get(ssusb->dev);
- if (IS_ERR(otg_sx->id_pinctrl)) {
- dev_err(ssusb->dev, "Cannot find id pinctrl!\n");
- return PTR_ERR(otg_sx->id_pinctrl);
- }
-
- otg_sx->id_float =
- pinctrl_lookup_state(otg_sx->id_pinctrl, "id_float");
- if (IS_ERR(otg_sx->id_float)) {
- dev_err(ssusb->dev, "Cannot find pinctrl id_float!\n");
- return PTR_ERR(otg_sx->id_float);
- }
-
- otg_sx->id_ground =
- pinctrl_lookup_state(otg_sx->id_pinctrl, "id_ground");
- if (IS_ERR(otg_sx->id_ground)) {
- dev_err(ssusb->dev, "Cannot find pinctrl id_ground!\n");
- return PTR_ERR(otg_sx->id_ground);
- }
-
- return 0;
-}
-
/* ignore the error if the clock does not exist */
static struct clk *get_optional_clk(struct device *dev, const char *id)
{
@@ -349,15 +321,11 @@ static int get_ssusb_rscs(struct platform_device *pdev, struct ssusb_mtk *ssusb)
dev_err(ssusb->dev, "couldn't get extcon device\n");
return -EPROBE_DEFER;
}
- if (otg_sx->manual_drd_enabled) {
- ret = get_iddig_pinctrl(ssusb);
- if (ret)
- return ret;
- }
}
- dev_info(dev, "dr_mode: %d, is_u3_dr: %d, u3p_dis_msk:%x\n",
- ssusb->dr_mode, otg_sx->is_u3_drd, ssusb->u3p_dis_msk);
+ dev_info(dev, "dr_mode: %d, is_u3_dr: %d, u3p_dis_msk: %x, drd: %s\n",
+ ssusb->dr_mode, otg_sx->is_u3_drd, ssusb->u3p_dis_msk,
+ otg_sx->manual_drd_enabled ? "manual" : "auto");
return 0;
}
--
1.7.9.5
More information about the linux-arm-kernel
mailing list