[PATCH v2] dts: display5: Device tree description of LWN's DISPLAY5 board
Lukasz Majewski
lukma at denx.de
Mon Sep 25 08:37:29 PDT 2017
This commit adds device tree description of Liebherr's Display5 board.
Signed-off-by: Lukasz Majewski <lukma at denx.de>
---
Changes for v2:
- Postpone adding Mitsubishi display
- Replace GPL with dual GPL/X11 licenses
- Remove superfluous "i2s-master" property
- Replace pinctrl 0x80000000 value (meaning that this ping shall not be
configured in Linux) with proper values (set by bootloader)
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/imx6q-display5-tianma-tm070-1280x768.dts | 51 ++
arch/arm/boot/dts/imx6q-display5.dtsi | 582 +++++++++++++++++++++
3 files changed, 634 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
create mode 100644 arch/arm/boot/dts/imx6q-display5.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35..c1648f0 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -400,6 +400,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cm-fx6.dtb \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
+ imx6q-display5-tianma-tm070-1280x768.dtb \
imx6q-dmo-edmqmx6.dtb \
imx6q-evi.dtb \
imx6q-gk802.dtb \
diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
new file mode 100644
index 0000000..16658b7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright 2017
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q-display5.dtsi"
+
+&panel {
+ compatible = "tianma,tm070jdhg30";
+};
+
+&ldb {
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/imx6q-display5.dtsi
new file mode 100644
index 0000000..a7d9144
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-display5.dtsi
@@ -0,0 +1,582 @@
+/*
+ * Copyright 2017
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Liebherr (LWN) display5 i.MX6 Quad Board";
+ compatible = "lwn,display5", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm2 0 5000000 0>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <250>;
+ enable-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lvds>;
+ gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbh1_vbus: usb-h1-vbus {
+ compatible = "regulator-fixed";
+ gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ label = "tfa9879-mono";
+
+ simple-audio-card,dai-link {
+ /* DAC */
+ format = "i2s";
+ bitclock-master = <&dailink_master>;
+ frame-master = <&dailink_master>;
+
+ dailink_master: cpu {
+ sound-dai = <&ssi2>;
+ };
+ codec {
+ sound-dai = <&codec>;
+ };
+ };
+ };
+
+ panel: panel-lvds0 {
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSEL(5) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(5) |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(5)
+ >;
+ };
+
+ aud6 {
+ fsl,audmux-port = <5>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_RFSEL(8) |
+ IMX_AUDMUX_V2_PTCR_RCSEL(8) |
+ IMX_AUDMUX_V2_PTCR_TFSEL(1) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(1) |
+ IMX_AUDMUX_V2_PTCR_RFSDIR |
+ IMX_AUDMUX_V2_PTCR_RCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+ >;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs &pinctrl_ecspi2_flwp>;
+ status = "okay";
+
+ s25fl256s: flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+
+ partition at 0 {
+ label = "SPL (spi)";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+ partition at 1 {
+ label = "u-boot (spi)";
+ reg = <0x20000 0x100000>;
+ read-only;
+ };
+ partition at 2 {
+ label = "uboot-env (spi)";
+ reg = <0x120000 0x10000>;
+ };
+ partition at 3 {
+ label = "uboot-envr (spi)";
+ reg = <0x130000 0x10000>;
+ };
+ partition at 4 {
+ label = "linux-recovery (spi)";
+ reg = <0x140000 0x800000>;
+ };
+ partition at 5 {
+ label = "swupdate-fitImg (spi)";
+ reg = <0x940000 0x400000>;
+ };
+ partition at 6 {
+ label = "swupdate-initramfs (spi)";
+ reg = <0xD40000 0x800000>;
+ };
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: tfa9879 at 6C {
+ #sound-dai-cells = <0>;
+ compatible = "tfa9879";
+ reg = <0x6C>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ at24 at 50 {
+ compatible = "at24,24c256";
+ pagesize = <64>;
+ reg = <0x50>;
+ };
+
+ pfuze100: pmic at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ #pwm-cells = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ /* I2S OUTPUT AUD6*/
+ MX6QDL_PAD_DI0_PIN4__AUD6_RXD 0x130b0
+ MX6QDL_PAD_DI0_PIN2__AUD6_TXD 0x130b0
+ MX6QDL_PAD_DI0_PIN3__AUD6_TXFS 0x130b0
+ MX6QDL_PAD_DI0_PIN15__AUD6_TXC 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi2_flwp: ecspi2flwpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi3_cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3_flwp: ecspi3flwpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_lvds: reqlvdsgrp {
+ fsl,pins = <
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D31__USB_H1_PWR 0x130b0
+ MX6QDL_PAD_EIM_D30__USB_H1_OC 0x030b0
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x17059
+ >;
+ };
+};
--
2.1.4
More information about the linux-arm-kernel
mailing list