[PATCH v2 1/3] media: V3s: Add support for Allwinner CSI.
Yong
yong.deng at magewell.com
Fri Sep 22 02:08:29 PDT 2017
Hello Mylène,
On Fri, 22 Sep 2017 10:44:13 +0200
Mylene JOSSERAND <mylene.josserand at free-electrons.com> wrote:
> Hello Yong,
>
> Thank you for these drivers!
>
> I tested it with an OV5640 camera on an Nanopi M1 plus (Allwinner H3)
> and I noticed that I got a frame correctly displayed only on a half of
> the frame's size.
>
> It is related to your "sun6i_csi_set_window" function (see
> below).
>
> > Allwinner V3s SoC have two CSI module. CSI0 is used for MIPI interface
> > and CSI1 is used for parallel interface. This is not documented in
> > datasheet but by testing and guess.
> >
> > This patch implement a v4l2 framework driver for it.
> >
> > Currently, the driver only support the parallel interface. MIPI-CSI2,
> > ISP's support are not included in this patch.
> >
> > Signed-off-by: Yong Deng <yong.deng at magewell.com>
> > ---
> > drivers/media/platform/Kconfig | 1 +
> > drivers/media/platform/Makefile | 2 +
> > drivers/media/platform/sun6i-csi/Kconfig | 9 +
> > drivers/media/platform/sun6i-csi/Makefile | 3 +
> > drivers/media/platform/sun6i-csi/sun6i_csi.c | 545
> > +++++++++++++++ drivers/media/platform/sun6i-csi/sun6i_csi.h |
> > 203 ++++++ drivers/media/platform/sun6i-csi/sun6i_csi_v3s.c | 827
> > +++++++++++++++++++++++
> > drivers/media/platform/sun6i-csi/sun6i_csi_v3s.h | 206 ++++++
> > drivers/media/platform/sun6i-csi/sun6i_video.c | 663
> > ++++++++++++++++++ drivers/media/platform/sun6i-csi/sun6i_video.h
> > | 61 ++ 10 files changed, 2520 insertions(+) create mode 100644
> > drivers/media/platform/sun6i-csi/Kconfig create mode 100644
> > drivers/media/platform/sun6i-csi/Makefile create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_csi.c create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_csi.h create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_csi_v3s.c create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_csi_v3s.h create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_video.c create mode 100644
> > drivers/media/platform/sun6i-csi/sun6i_video.h
> >
> > diff --git a/drivers/media/platform/Kconfig
> > b/drivers/media/platform/Kconfig index 0c741d1..8371a87 100644
> > --- a/drivers/media/platform/Kconfig
> > +++ b/drivers/media/platform/Kconfig
> > @@ -143,6 +143,7 @@ source "drivers/media/platform/am437x/Kconfig"
> > source "drivers/media/platform/xilinx/Kconfig"
> > source "drivers/media/platform/rcar-vin/Kconfig"
> > source "drivers/media/platform/atmel/Kconfig"
> > +source "drivers/media/platform/sun6i-csi/Kconfig"
> >
>
> <snip>
>
> > +static void sun6i_csi_set_format(struct sun6i_csi_dev *sdev)
> > +{
> > + struct sun6i_csi *csi = &sdev->csi;
> > + u32 cfg;
> > + u32 val;
> > +
> > + regmap_read(sdev->regmap, CSI_CH_CFG_REG, &cfg);
> > +
> > + cfg &= ~(CSI_CH_CFG_INPUT_FMT_MASK |
> > + CSI_CH_CFG_OUTPUT_FMT_MASK | CSI_CH_CFG_VFLIP_EN |
> > + CSI_CH_CFG_HFLIP_EN | CSI_CH_CFG_FIELD_SEL_MASK |
> > + CSI_CH_CFG_INPUT_SEQ_MASK);
> > +
> > + val = get_csi_input_format(csi->config.code,
> > csi->config.pixelformat);
> > + cfg |= CSI_CH_CFG_INPUT_FMT(val);
> > +
> > + val = get_csi_output_format(csi->config.code,
> > csi->config.field);
> > + cfg |= CSI_CH_CFG_OUTPUT_FMT(val);
> > +
> > + val = get_csi_input_seq(csi->config.code,
> > csi->config.pixelformat);
> > + cfg |= CSI_CH_CFG_INPUT_SEQ(val);
> > +
> > + if (csi->config.field == V4L2_FIELD_TOP)
> > + cfg |= CSI_CH_CFG_FIELD_SEL_FIELD0;
> > + else if (csi->config.field == V4L2_FIELD_BOTTOM)
> > + cfg |= CSI_CH_CFG_FIELD_SEL_FIELD1;
> > + else
> > + cfg |= CSI_CH_CFG_FIELD_SEL_BOTH;
> > +
> > + regmap_write(sdev->regmap, CSI_CH_CFG_REG, cfg);
> > +}
> > +
> > +static void sun6i_csi_set_window(struct sun6i_csi_dev *sdev)
> > +{
> > + struct sun6i_csi_config *config = &sdev->csi.config;
> > + u32 bytesperline_y;
> > + u32 bytesperline_c;
> > + int *planar_offset = sdev->planar_offset;
> > +
> > + regmap_write(sdev->regmap, CSI_CH_HSIZE_REG,
> > + CSI_CH_HSIZE_HOR_LEN(config->width) |
> > + CSI_CH_HSIZE_HOR_START(0));
> > + regmap_write(sdev->regmap, CSI_CH_VSIZE_REG,
> > + CSI_CH_VSIZE_VER_LEN(config->height) |
> > + CSI_CH_VSIZE_VER_START(0));
>
> In my case, the HOR_LEN and VER_LEN were not correctly configured.
>
> They were configured to width and height (640 * 480) but as I was
> using a YUYV format, the pixel's size is 2 bytes so the
> horizontal/vertical lines' lengths were divided by 2.
>
> Currently, I fixed that by getting the number of bytes per pixel with
> "v4l2_pixformat_get_bpp()":
>
> + int bytes_pixel;
> +
> + bytes_pixel = v4l2_pixformat_get_bpp(config->pixelformat) / 8;
>
> regmap_write(sdev->regmap, CSI_CH_HSIZE_REG,
> - CSI_CH_HSIZE_HOR_LEN(config->width) |
> + CSI_CH_HSIZE_HOR_LEN(config->width * bytes_pixel) |
> CSI_CH_HSIZE_HOR_START(0));
> regmap_write(sdev->regmap, CSI_CH_VSIZE_REG,
> - CSI_CH_VSIZE_VER_LEN(config->height) |
> + CSI_CH_VSIZE_VER_LEN(config->height * bytes_pixel)
> | CSI_CH_VSIZE_VER_START(0));
>
> There is certainly a nicer way to handle that.
The datasheet documents CSI_CH_HSIZE_HOR_LEN and CSI_CH_VSIZE_VER_LEN's
unit is pixel. And I had tested the YUYV format on V3s and that's OK.
Another register CSI_CH_BUF_LEN_REG's unit is byte.
>
> > +
> > + planar_offset[0] = 0;
> > + switch(config->pixelformat) {
> > + case V4L2_PIX_FMT_HM12:
> > + case V4L2_PIX_FMT_NV12:
> > + case V4L2_PIX_FMT_NV21:
> > + case V4L2_PIX_FMT_NV16:
> > + case V4L2_PIX_FMT_NV61:
> > + bytesperline_y = config->width;
> > + bytesperline_c = config->width;
> > + planar_offset[1] = bytesperline_y * config->height;
> > + planar_offset[2] = -1;
> > + break;
> > + case V4L2_PIX_FMT_YUV420:
> > + case V4L2_PIX_FMT_YVU420:
> > + bytesperline_y = config->width;
> > + bytesperline_c = config->width / 2;
> > + planar_offset[1] = bytesperline_y * config->height;
> > + planar_offset[2] = planar_offset[1] +
> > + bytesperline_c * config->height / 2;
> > + break;
> > + case V4L2_PIX_FMT_YUV422P:
> > + bytesperline_y = config->width;
> > + bytesperline_c = config->width / 2;
> > + planar_offset[1] = bytesperline_y * config->height;
> > + planar_offset[2] = planar_offset[1] +
> > + bytesperline_c * config->height;
> > + break;
> > + default: /* raw */
> > + bytesperline_y =
> > (v4l2_pixformat_get_bpp(config->pixelformat) *
> > + config->width) / 8;
> > + bytesperline_c = 0;
> > + planar_offset[1] = -1;
> > + planar_offset[2] = -1;
> > + break;
> > + }
> > +
> > + regmap_write(sdev->regmap, CSI_CH_BUF_LEN_REG,
> > + CSI_CH_BUF_LEN_BUF_LEN_C(bytesperline_c) |
> > + CSI_CH_BUF_LEN_BUF_LEN_Y(bytesperline_y));
> > +}
> > +
> > +static int get_supported_pixformats(struct sun6i_csi *csi,
> > + const u32 **pixformats)
> > +{
> > + if (pixformats != NULL)
> > + *pixformats = supported_pixformats;
> > +
> > + return ARRAY_SIZE(supported_pixformats);
> > +}
> > +
> > +static bool is_format_support(struct sun6i_csi *csi, u32 pixformat,
> > + u32 mbus_code)
> > +{
> > + struct sun6i_csi_dev *sdev = sun6i_csi_to_dev(csi);
> > +
> > + return __is_format_support(sdev, pixformat, mbus_code);
> > +}
> > +
> > +static int set_power(struct sun6i_csi *csi, bool enable)
> > +{
> > + struct sun6i_csi_dev *sdev = sun6i_csi_to_dev(csi);
> > + struct regmap *regmap = sdev->regmap;
> > + int ret;
> > +
> > + if (!enable) {
> > + regmap_update_bits(regmap, CSI_EN_REG,
> > CSI_EN_CSI_EN, 0); +
> > + clk_disable_unprepare(sdev->clk_ram);
> > + clk_disable_unprepare(sdev->clk_mod);
> > + clk_disable_unprepare(sdev->clk_ahb);
> > + reset_control_assert(sdev->rstc_ahb);
> > + return 0;
> > + }
> > +
> > + ret = clk_prepare_enable(sdev->clk_ahb);
> > + if (ret) {
> > + dev_err(sdev->dev, "Enable ahb clk err %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = clk_prepare_enable(sdev->clk_mod);
> > + if (ret) {
> > + dev_err(sdev->dev, "Enable csi clk err %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = clk_prepare_enable(sdev->clk_ram);
> > + if (ret) {
> > + dev_err(sdev->dev, "Enable clk_dram_csi clk err
> > %d\n", ret);
> > + return ret;
> > + }
> > +
> > + if (!IS_ERR_OR_NULL(sdev->rstc_ahb)) {
> > + ret = reset_control_deassert(sdev->rstc_ahb);
> > + if (ret) {
> > + dev_err(sdev->dev, "reset err %d\n", ret);
> > + return ret;
> > + }
> > + }
> > +
> > + regmap_update_bits(regmap, CSI_EN_REG, CSI_EN_CSI_EN,
> > CSI_EN_CSI_EN); +
> > + return 0;
> > +}
>
> <snip>
>
> Thank you in advance!
>
> Best regards,
>
> --
> Mylène Josserand, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Thanks,
Yong
More information about the linux-arm-kernel
mailing list