[PATCH v2 9/9] tty/serial: atmel: Prevent a warning on suspend
Richard Genoud
richard.genoud at gmail.com
Wed Sep 20 07:35:05 PDT 2017
On 15/09/2017 16:04, Romain Izard wrote:
> The atmel serial port driver reported the following warning on suspend:
> atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
>
> As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
> when the transmitter is disabled, we need to know the transmitter's
> state to return the real fifo state. And as ATMEL_US_CR is write-only,
> it is necessary to save the state of the transmitter in a local
> variable, and update the variable when TXEN and TXDIS is written in
> ATMEL_US_CR.
>
> After those changes, atmel_tx_empty can return "empty" on suspend, the
> warning in uart_suspend_port disappears, and suspending is 20ms shorter
> for each enabled Atmel serial port.
>
> Signed-off-by: Romain Izard <romain.izard.pro at gmail.com>
> ---
> drivers/tty/serial/atmel_serial.c | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 7551cab438ff..783af6648be0 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -171,6 +171,7 @@ struct atmel_uart_port {
> bool has_hw_timer;
> struct timer_list uart_timer;
>
> + bool tx_stopped;
> bool suspended;
> unsigned int pending;
> unsigned int pending_status;
> @@ -380,6 +381,10 @@ static int atmel_config_rs485(struct uart_port *port,
> */
> static u_int atmel_tx_empty(struct uart_port *port)
> {
> + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> +
> + if (atmel_port->tx_stopped)
> + return TIOCSER_TEMT;
> return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
> TIOCSER_TEMT :
> 0;
> @@ -485,6 +490,7 @@ static void atmel_stop_tx(struct uart_port *port)
> * is fully transmitted.
> */
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
> + atmel_port->tx_stopped = true;
>
> /* Disable interrupts */
> atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
> @@ -492,6 +498,7 @@ static void atmel_stop_tx(struct uart_port *port)
> if ((port->rs485.flags & SER_RS485_ENABLED) &&
> !(port->rs485.flags & SER_RS485_RX_DURING_TX))
> atmel_start_rx(port);
> +
> }
This line feed is not needed.
Otherwise,
Acked-by: Richard Genoud <richard.genoud at gmail.com>
>
> /*
> @@ -521,6 +528,7 @@ static void atmel_start_tx(struct uart_port *port)
>
> /* re-enable the transmitter */
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
> + atmel_port->tx_stopped = false;
> }
>
> /*
> @@ -1866,6 +1874,7 @@ static int atmel_startup(struct uart_port *port)
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> /* enable xmit & rcvr */
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_port->tx_stopped = false;
>
> setup_timer(&atmel_port->uart_timer,
> atmel_uart_timer_callback,
> @@ -2122,6 +2131,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>
> /* disable receiver and transmitter */
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
> + atmel_port->tx_stopped = true;
>
> /* mode */
> if (port->rs485.flags & SER_RS485_ENABLED) {
> @@ -2207,6 +2217,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_port->tx_stopped = false;
>
> /* restore interrupts */
> atmel_uart_writel(port, ATMEL_US_IER, imr);
> @@ -2450,6 +2461,7 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
>
> /* Make sure that tx path is actually able to send characters */
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
> + atmel_port->tx_stopped = false;
>
> uart_console_write(port, s, count, atmel_console_putchar);
>
> @@ -2511,6 +2523,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
> {
> int ret;
> struct uart_port *port = &atmel_ports[co->index].uart;
> + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> int baud = 115200;
> int bits = 8;
> int parity = 'n';
> @@ -2528,6 +2541,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
> atmel_uart_writel(port, ATMEL_US_IDR, -1);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
> + atmel_port->tx_stopped = false;
>
> if (options)
> uart_parse_options(options, &baud, &parity, &bits, &flow);
>
More information about the linux-arm-kernel
mailing list