[GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.15

[Simon Horman]

On Thu, Oct 19, 2017 at 11:39:45PM +0200, Arnd Bergmann wrote:
> On Fri, Sep 29, 2017 at 1:52 PM, Simon Horman
> <horms+renesas at verge.net.au> wrote:
> > ----------------------------------------------------------------
> > Renesas ARM64 Based SoC DT Updates for v4.15
> >
> > * r8a7795 (H3)
> >   - Use r8a7795-cpg-mssr and r8a7795-sysc bindings
> >     Hardcoded indicies are replaced with symbols now that they are available
> >
> >   - Drop bogus HDMI node name suffixes
> >     Laurent Pinchart says: Node names should not use numerical suffixes if
> >     the nodes can be distinguished by unit-address
> >
> >   - Update PFC node name to pin-controller
> >     Shimoda-san says the PFC node name is changed "from e6060000.pfc and
> >     pfc at e6060000 to e6060000.pin-controller and pin-controller at e6060000
> >     like other Renesas SoCs."
> >
> > * r8a7795 (H3) ES1.0
> >   - Drop extra zero from XHCI unit address
> >     This corrects a typo were ee0400000 rather than ee040000 was used
> >     as the unit address.
> >
> > * r8a7796 (M3-W)
> >   - Add FDP1 instance
> >     Laurent Pinchart says: The r8a7796 has a single FDP1 instance.
> >
> > * r8a7795 (H3) and r8a7796 (M3-W) SoCs
> >   - Add USB3.0 peripheral device nodes
> >     Shimoda-san says that this is not enabled on the Salvator-X/XS boards
> >     for now as:
> >      + we need a special cable (USB type-A to A cross cable).
> >      + we can swap the role by renesas_usb3 driver even if we use a normal
> >         cable and after usb3.0 host is running, but I think it's a special
> >         use case.
> >
> > * r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
> >   - Enable display output
> >     Laurent Pinchart says: The DU is already wired up to the HDMI encoder,
> >     all we need to do is enable it.
> >
> > * r8a77995 (D3) Draak board
> >   - Enable EthernetAVB and , USB2.0 Host and PHY
> >
> >   - Add serial console pins.
> >     This is safe to do now that r8a77995 PFC driver support is present
> >
> > * r8a77970 (V3M)
> >   - Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes
> >     This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC
> >     in the Eagle board support for which is under review
> 
> Thanks for the detailed changelog!
> 
> > ----------------------------------------------------------------
> > Geert Uytterhoeven (6):
> >       arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address
> >       arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
> >       arm64: renesas: Add Renesas R8A77970 Kconfig support
> 
> That one last commit doesn't seem to belong in here, but I've pulled
> it anyway, thanks!

Thanks! I take it you would have prefered this in an soc branch?