[PATCH] i2c: stm32: Fixes multibyte transfer for STM32F4 I2C controller

[Pierre Yves MORDRET]

On 10/12/2017 11:55 AM, Radosław Pietrzyk wrote:
> It looks like there is a use case when IRQ handler is delayed a bit
> and the logic in the driver does not work. What is the real root cause
> I don't know.
> 

As far as I know on this STM32 F4 platform there is some trouble with timer
events that may have bad influences on scheduling. Some tasks could be delayed
for some reasons.
It would be great if the following patches below could help in your matter
https://patchwork.kernel.org/patch/9980961/
https://patchwork.kernel.org/patch/9980963/
https://patchwork.kernel.org/patch/9980965/
https://patchwork.kernel.org/patch/9980967/

Would you mind to test those ?
Thanks

> 2017-10-12 11:31 GMT+02:00 Pierre Yves MORDRET <pierre-yves.mordret at st.com>:
>>
>>
>> On 10/11/2017 01:53 PM, Radoslaw Pietrzyk wrote:
>>>       Do not read data on RXNE but on BTF only due to HW
>>>       synchronisation problems and NACKing read data too early.
>>>       It was found during testing of stmpe811 touchscreen driver.
>>>
>>
>> Would you mind to explain what is behind "hw sync issue" you've seen ?
>>
>>> Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk at gmail.com>
>>> ---
>>>  drivers/i2c/busses/i2c-stm32f4.c | 11 +----------
>>>  1 file changed, 1 insertion(+), 10 deletions(-)
>>>
>>> diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
>>> index 4ec1084..86bcf4c 100644
>>> --- a/drivers/i2c/busses/i2c-stm32f4.c
>>> +++ b/drivers/i2c/busses/i2c-stm32f4.c
>>> @@ -409,16 +409,9 @@ static void stm32f4_i2c_handle_read(struct stm32f4_i2c_dev *i2c_dev)
>>>        * So, here we just disable buffer interrupt in order to avoid another
>>>        * system preemption due to RX not empty event.
>>>        */
>>> -     case 2:
>>> -     case 3:
>>> +     default:
>>>               stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
>>>               break;
>>> -     /*
>>> -      * For N byte reception with N > 3 we directly read data register
>>> -      * until N-2 data.
>>> -      */
>>> -     default:
>>> -             stm32f4_i2c_read_msg(i2c_dev);
>>>       }
>>>  }
>>>
>>> @@ -470,8 +463,6 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>>>                */
>>>               reg = i2c_dev->base + STM32F4_I2C_CR1;
>>>               stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
>>> -             stm32f4_i2c_read_msg(i2c_dev);
>>> -             break;
>>>       default:
>>>               stm32f4_i2c_read_msg(i2c_dev);
>>>       }
>>>