[PATCH net-next v2 1/2] dt-bindings: net: add DT bindings for Socionext UniPhier AVE

[Masahiro Yamada]

2017-10-13 9:35 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko at socionext.com>:
> DT bindings for the AVE ethernet controller found on Socionext's
> UniPhier platforms.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
> Signed-off-by: Jassi Brar <jaswinder.singh at linaro.org>
> ---
>  .../bindings/net/socionext,uniphier-ave4.txt       | 53 ++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
>
> diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> new file mode 100644
> index 0000000..25f4d92
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> @@ -0,0 +1,53 @@
> +* Socionext AVE ethernet controller
> +
> +This describes the devicetree bindings for AVE ethernet controller
> +implemented on Socionext UniPhier SoCs.
> +
> +Required properties:
> + - compatible: Should be
> +       - "socionext,uniphier-pro4-ave4" : for Pro4 SoC
> +       - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
> +       - "socionext,uniphier-ld20-ave4" : for LD20 SoC
> +       - "socionext,uniphier-ld11-ave4" : for LD11 SoC
> + - reg: Address where registers are mapped and size of region.
> + - interrupts: Should contain the MAC interrupt.
> + - phy-mode: See ethernet.txt in the same directory. Allow to choose
> +       "rgmii", "rmii", or "mii" according to the PHY.
> + - pinctrl-names: List of assigned state names, see pinctrl
> +       binding documentation.
> + - pinctrl-0: List of phandles to configure the GPIO pin,
> +       see pinctrl binding documentation. Choose this appropriately
> +       according to phy-mode.
> +       - <&pinctrl_ether_rgmii> if phy-mode is "rgmii".
> +       - <&pinctrl_ether_rmii> if phy-mode is "rmii".
> +       - <&pinctrl_ether_mii> if phy-mode is "mii".
> + - phy-handle: Should point to the external phy device.
> +       See ethernet.txt file in the same directory.
> + - mdio subnode: Should be device tree subnode with the following required
> +       properties:
> +       - #address-cells: Must be <1>.
> +       - #size-cells: Must be <0>.
> +       - reg: phy ID number, usually a small integer.
> +
> +Optional properties:
> + - local-mac-address: See ethernet.txt in the same directory.
> +
> +Example:
> +
> +       ether: ethernet at 65000000 {
> +               compatible = "socionext,uniphier-ld20-ave4";
> +               reg = <0x65000000 0x8500>;
> +               interrupts = <0 66 4>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_ether_rgmii>;
> +               phy-mode = "rgmii";
> +               phy-handle = <&ethphy>;
> +               local-mac-address = [00 00 00 00 00 00];
> +               mdio {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       ethphy: ethphy at 1 {
> +                               reg = <1>;
> +                       };
> +               };
> +       };
> --
> 2.7.4
>


I found the following code in 2/2.

+ /* get clock */
+ priv->clk = clk_get(dev, NULL);
+ if (IS_ERR(priv->clk))
+ priv->clk = NULL;
+
+ /* get reset */
+ priv->rst = reset_control_get(dev, NULL);
+ if (IS_ERR(priv->rst))
+ priv->rst = NULL;
+


This doc needs to describe "clocks", "resets".


-- 
Best Regards
Masahiro Yamada