[PATCH v2] arm64: dts: hikey960: Update HiKey960 with GPIO line names
Wei Xu
xuwei5 at hisilicon.com
Fri Oct 13 01:54:35 PDT 2017
Hi Linus,
On 2017/10/3 9:59, Linus Walleij wrote:
> This adds line names for all the GPIOs I could identify on the HiKey960
> schematic.
>
> "GPIO-A" through "GPIO-L" are the most important since they give users
> a handle to look up the standard 96boards GPIOs from the GPIO character
> device.
>
> The rest of the names are more informational, nice debug information
> for "lsgpio" so you can see that the right line is taken for the right
> function in the kernel for example.
>
> Cc: Wei Xu <xuwei5 at hisilicon.com>
> Cc: Zhangfei Gao <zhangfei.gao at hisilicon.com>
> Cc: Guodong Xu <guodong.xu at linaro.org>
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
> ---
Applied into hisilicon dt tree.
Thanks!
BR,
Wei
> ChangeLog v1->v2:
> - Make sure the DTS file compiles. A semicolon was missing. Sorry,
> didn't have the right Aarch64 compiler to test it before.
>
> Wei: can you test this please? I'm not sure it even compiles but
> I think it should look like this with maybe minor tweaks, if you know
> some of the undefined lines or see some errors feel free to fix it
> up.
> ---
> arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 319 ++++++++++++++++++++++
> 1 file changed, 319 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> index fd4705c451e2..21e7618b8e97 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
> @@ -196,6 +196,325 @@
> };
> };
>
> +/*
> + * Legend: proper name = the GPIO line is used as GPIO
> + * NC = not connected (pin out but not routed from the chip to
> + * anything the board)
> + * "[PER]" = pin is muxed for [peripheral] (not GPIO)
> + * "" = no idea, schematic doesn't say, could be
> + * unrouted (not connected to any external pin)
> + * LSEC = Low Speed External Connector
> + * HSEC = High Speed External Connector
> + *
> + * Line names are taken from "HiKey 960 Board ver A" schematics
> + * from Huawei. The 40 pin low speed expansion connector is named
> + * J2002 63453-140LF.
> + *
> + * For the lines routed to the external connectors the
> + * lines are named after the 96Boards CE Specification 1.0,
> + * Appendix "Expansion Connector Signal Description".
> + *
> + * When the 96Board naming of a line and the schematic name of
> + * the same line are in conflict, the 96Board specification
> + * takes precedence, which means that the external UART on the
> + * LSEC is named UART0 while the schematic and SoC names this
> + * UART3. This is only for the informational lines i.e. "[FOO]",
> + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
> + * ones actually used for GPIO.
> + */
> +&gpio0 {
> + /* GPIO_000-GPIO_007 */
> + gpio-line-names =
> + "",
> + "TP901", /* TEST_MODE connected to TP901 */
> + "[PMU0_SSI]",
> + "[PMU1_SSI]",
> + "[PMU2_SSI]",
> + "[PMU0_CLKOUT]",
> + "[JTAG_TCK]",
> + "[JTAG_TMS]";
> +};
> +
> +&gpio1 {
> + /* GPIO_008-GPIO_015 */
> + gpio-line-names =
> + "[JTAG_TRST_N]",
> + "[JTAG_TDI]",
> + "[JTAG_TDO]",
> + "NC", "NC",
> + "[I2C3_SCL]",
> + "[I2C3_SDA]",
> + "NC";
> +};
> +
> +&gpio2 {
> + /* GPIO_016-GPIO_023 */
> + gpio-line-names =
> + "NC", "NC", "NC",
> + "GPIO-J", /* LSEC pin 32: GPIO_019 */
> + "GPIO_020_HDMI_SEL",
> + "GPIO-L", /* LSEC pin 34: GPIO_021 */
> + "GPIO_022_UFSBUCK_INT_N",
> + "GPIO-G"; /* LSEC pin 29: LCD_TE0 */
> +};
> +
> +&gpio3 {
> + /* GPIO_024-GPIO_031 */
> + /* The rail from pin BK36 is named LCD_TE0, we assume to be muxed as GPIO for GPIO-G */
> + gpio-line-names =
> + "[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
> + "[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
> + "NC",
> + "[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
> + "[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
> + "[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
> + "[I2C3_SDA]", /* HSEC pin 38: ISP_SDA1 */
> + "NC";
> +};
> +
> +&gpio4 {
> + /* GPIO_032-GPIO_039 */
> + gpio-line-names =
> + "NC", "NC",
> + "PWR_BTN_N", /* LSEC pin 4: GPIO_034_PWRON_DET */
> + "GPIO_035_PMU2_EN",
> + "GPIO_036_USB_HUB_RESET",
> + "NC", "NC", "NC";
> +};
> +
> +&gpio5 {
> + /* GPIO_040-GPIO_047 */
> + gpio-line-names =
> + "GPIO-H", /* LSEC pin 30: GPIO_040_LCD_RST_N */
> + "GPIO_041_HDMI_PD",
> + "TP904", /* Test point */
> + "TP905", /* Test point */
> + "NC", "NC",
> + "GPIO_046_HUB_VDD33_EN",
> + "GPIO_047_PMU1_EN";
> +};
> +
> +&gpio6 {
> + /* GPIO_048-GPIO_055 */
> + gpio-line-names =
> + "NC", "NC", "NC",
> + "GPIO_051_WIFI_EN",
> + "GPIO-I", /* LSEC pin 31: GPIO_052_CAM0_RST_N */
> + /*
> + * These two pins should be used for SD(IO) data according to the
> + * 96boards specification but seems to be repurposed for a IRDA UART.
> + * They are however named according to the spec.
> + */
> + "[SD_DAT1]", /* HSEC pin 3: UART0_IRDA_RXD */
> + "[SD_DAT2]", /* HSEC pin 5: UART0_IRDA_TXD */
> + "[UART1_RXD]"; /* LSEC pin 13: DEBUG_UART6_RXD */
> +};
> +
> +&gpio7 {
> + /* GPIO_056-GPIO_063 */
> + gpio-line-names =
> + "[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
> + "[UART0_CTS]", /* LSEC pin 3: UART3_CTS_N */
> + "[UART0_RTS]", /* LSEC pin 9: UART3_RTS_N */
> + "[UART0_RXD]", /* LSEC pin 7: UART3_RXD */
> + "[UART0_TXD]", /* LSEC pin 5: UART3_TXD */
> + "[SOC_BT_UART4_CTS_N]",
> + "[SOC_BT_UART4_RTS_N]",
> + "[SOC_BT_UART4_RXD]";
> +};
> +
> +&gpio8 {
> + /* GPIO_064-GPIO_071 */
> + gpio-line-names =
> + "[SOC_BT_UART4_TXD]",
> + "NC",
> + "[PMU_HKADC_SSI]",
> + "NC",
> + "GPIO_068_SEL",
> + "NC", "NC", "NC";
> +
> +};
> +
> +&gpio9 {
> + /* GPIO_072-GPIO_079 */
> + gpio-line-names =
> + "NC", "NC", "NC",
> + "GPIO-K", /* LSEC pin 33: GPIO_075_CAM1_RST_N */
> + "NC", "NC", "NC", "NC";
> +};
> +
> +&gpio10 {
> + /* GPIO_080-GPIO_087 */
> + gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
> +};
> +
> +&gpio11 {
> + /* GPIO_088-GPIO_095 */
> + gpio-line-names =
> + "NC",
> + "[PCIE_PERST_N]",
> + "NC", "NC", "NC", "NC", "NC", "NC";
> +};
> +
> +&gpio12 {
> + /* GPIO_096-GPIO_103 */
> + gpio-line-names = "NC", "NC", "NC", "", "", "", "", "NC";
> +};
> +
> +&gpio13 {
> + /* GPIO_104-GPIO_111 */
> + gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
> +};
> +
> +&gpio14 {
> + /* GPIO_112-GPIO_119 */
> + gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
> +};
> +
> +&gpio15 {
> + /* GPIO_120-GPIO_127 */
> + gpio-line-names =
> + "NC", "NC", "NC", "NC", "NC", "NC",
> + "GPIO_126_BT_EN",
> + "TP902"; /* GPIO_127_JTAG_SEL0 */
> +};
> +
> +&gpio16 {
> + /* GPIO_128-GPIO_135 */
> + gpio-line-names = "", "", "", "", "", "", "", "";
> +};
> +
> +&gpio17 {
> + /* GPIO_136-GPIO_143 */
> + gpio-line-names = "", "", "", "", "", "", "", "";
> +};
> +
> +&gpio18 {
> + /* GPIO_144-GPIO_151 */
> + gpio-line-names =
> + "[UFS_REF_CLK]",
> + "[UFS_RST_N]",
> + "[SPI1_SCLK]", /* HSEC pin 9: GPIO_146_SPI3_CLK */
> + "[SPI1_DIN]", /* HSEC pin 11: GPIO_147_SPI3_DI */
> + "[SPI1_DOUT]", /* HSEC pin 1: GPIO_148_SPI3_DO */
> + "[SPI1_CS]", /* HSEC pin 7: GPIO_149_SPI3_CS0_N */
> + "GPIO_150_USER_LED1",
> + "GPIO_151_USER_LED2";
> +};
> +
> +&gpio19 {
> + /* GPIO_152-GPIO_159 */
> + gpio-line-names = "NC", "NC", "NC", "NC", "", "", "", "";
> +};
> +
> +&gpio20 {
> + /* GPIO_160-GPIO_167 */
> + gpio-line-names =
> + "[SD_CLK]",
> + "[SD_CMD]",
> + "[SD_DATA0]",
> + "[SD_DATA1]",
> + "[SD_DATA2]",
> + "[SD_DATA3]",
> + "", "";
> +};
> +
> +&gpio21 {
> + /* GPIO_168-GPIO_175 */
> + gpio-line-names =
> + "[WL_SDIO_CLK]",
> + "[WL_SDIO_CMD]",
> + "[WL_SDIO_DATA0]",
> + "[WL_SDIO_DATA1]",
> + "[WL_SDIO_DATA2]",
> + "[WL_SDIO_DATA3]",
> + "", "";
> +};
> +
> +&gpio22 {
> + /* GPIO_176-GPIO_183 */
> + gpio-line-names =
> + "[GPIO_176_PMU_PWR_HOLD]",
> + "NA",
> + "[SYSCLK_EN]",
> + "GPIO_179_WL_WAKEUP_AP",
> + "GPIO_180_HDMI_INT",
> + "NA",
> + "GPIO-F", /* LSEC pin 28: LCD_BL_PWM */
> + "[I2C0_SCL]"; /* LSEC pin 15 */
> +};
> +
> +&gpio23 {
> + /* GPIO_184-GPIO_191 */
> + gpio-line-names =
> + "[I2C0_SDA]", /* LSEC pin 17 */
> + "[I2C1_SCL]", /* Actual SoC I2C1 */
> + "[I2C1_SDA]", /* Actual SoC I2C1 */
> + "[I2C1_SCL]", /* LSEC pin 19: I2C7_SCL */
> + "[I2C1_SDA]", /* LSEC pin 21: I2C7_SDA */
> + "GPIO_189_USER_LED3",
> + "GPIO_190_USER_LED4",
> + "";
> +};
> +
> +&gpio24 {
> + /* GPIO_192-GPIO_199 */
> + gpio-line-names =
> + "[PCM_DI]", /* LSEC pin 22: GPIO_192_I2S0_DI */
> + "[PCM_DO]", /* LSEC pin 20: GPIO_193_I2S0_DO */
> + "[PCM_CLK]", /* LSEC pin 18: GPIO_194_I2S0_XCLK */
> + "[PCM_FS]", /* LSEC pin 16: GPIO_195_I2S0_XFS */
> + "[GPIO_196_I2S2_DI]",
> + "[GPIO_197_I2S2_DO]",
> + "[GPIO_198_I2S2_XCLK]",
> + "[GPIO_199_I2S2_XFS]";
> +};
> +
> +&gpio25 {
> + /* GPIO_200-GPIO_207 */
> + gpio-line-names =
> + "NC",
> + "NC",
> + "GPIO_202_VBUS_TYPEC",
> + "GPIO_203_SD_DET",
> + "GPIO_204_PMU12_IRQ_N",
> + "GPIO_205_WIFI_ACTIVE",
> + "GPIO_206_USBSW_SEL",
> + "GPIO_207_BT_ACTIVE";
> +};
> +
> +&gpio26 {
> + /* GPIO_208-GPIO_215 */
> + gpio-line-names =
> + "GPIO-A", /* LSEC pin 23: GPIO_208 */
> + "GPIO-B", /* LSEC pin 24: GPIO_209 */
> + "GPIO-C", /* LSEC pin 25: GPIO_210 */
> + "GPIO-D", /* LSEC pin 26: GPIO_211 */
> + "GPIO-E", /* LSEC pin 27: GPIO_212 */
> + "[PCIE_CLKREQ_N]",
> + "[PCIE_WAKE_N]",
> + "[SPI0_CLK]"; /* LSEC pin 8: SPI2_CLK */
> +};
> +
> +&gpio27 {
> + /* GPIO_216-GPIO_223 */
> + gpio-line-names =
> + "[SPI0_DIN]", /* LSEC pin 10: SPI2_DI */
> + "[SPI0_DOUT]", /* LSEC pin 14: SPI2_DO */
> + "[SPI0_CS]", /* LSEC pin 12: SPI2_CS0_N */
> + "GPIO_219_CC_INT",
> + "NC",
> + "NC",
> + "[PMU_INT]",
> + "";
> +};
> +
> +&gpio28 {
> + /* GPIO_224-GPIO_231 */
> + gpio-line-names =
> + "", "", "", "", "", "", "", "";
> +};
> +
> &i2c0 {
> /* On Low speed expansion */
> label = "LS-I2C0";
>
More information about the linux-arm-kernel
mailing list