[PATCH 09/15] ARM: dts: at91: sama5d2_xplained: Add charger node of pmic.

[Yang, Wenyou]

Hi Claudiu,


On 2017/10/10 0:09, Claudiu Beznea wrote:
> Add charger device node as a sub-device node of act8945a mfd, move
> the charger's properties to this node, and use the "interrupts"
> property to replace "active-semi,irq_gpios" to denote the act8945a
> charger's irq.
>
> Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> [claudiu.beznea at microchip.com: replace numbers with pin macros]
> Signed-off-by: Claudiu Beznea <claudiu.beznea at microchip.com>
This patch has already applied on at91-dt branch.
https://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux.git/commit/?h=at91-dt&id=4b6ad41f267b8ddabf5dd1b02a318bc74f0b95e9

> ---
>   arch/arm/boot/dts/at91-sama5d2_xplained.dts | 23 +++++++++++++++--------
>   1 file changed, 15 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> index c7e9ccf2bc87..848ca1b025be 100644
> --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> @@ -160,14 +160,6 @@
>   					compatible = "active-semi,act8945a";
>   					reg = <0x5b>;
>   					active-semi,vsel-high;
> -					active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
> -					active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
> -					active-semi,irq_gpios = <&pioA PIN_PB13 GPIO_ACTIVE_LOW>;
> -					active-semi,input-voltage-threshold-microvolt = <6600>;
> -					active-semi,precondition-timeout = <40>;
> -					active-semi,total-timeout = <3>;
> -					pinctrl-names = "default";
> -					pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
>   					status = "okay";
>   
>   					regulators {
> @@ -220,6 +212,21 @@
>   							regulator-always-on;
>   						};
>   					};
> +
> +					charger {
> +						compatible = "active-semi,act8945a-charger";
> +						pinctrl-names = "default";
> +						pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
> +						interrupt-parent = <&pioA>;
> +						interrupts = <PIN_PB13 GPIO_ACTIVE_LOW>;
> +
> +						active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
> +						active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
> +						active-semi,input-voltage-threshold-microvolt = <6600>;
> +						active-semi,precondition-timeout = <40>;
> +						active-semi,total-timeout = <3>;
> +						status = "okay";
> +					};
>   				};
>   			};
>   

Best Regards,
Wenyou Yang