[PATCH 1/4] ARM: dts: qcom: msm8974: Add Sony Xperia Z2 Tablet
Bjorn Andersson
bjorn.andersson at linaro.org
Wed Oct 4 11:58:54 PDT 2017
From: Bjorn Andersson <bjorn.andersson at sonymobile.com>
This adds a basic DTS file for the Sony Xperia Z2 Tablet, containing
definitions for regulators, eMMC/SD-card, USB, WiFi, Touchscreen,
charger, backlight, coincell and buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson at sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson at linaro.org>
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/qcom-msm8974-sony-xperia-castor.dts | 641 +++++++++++++++++++++
arch/arm/boot/dts/qcom-msm8974.dtsi | 14 +
arch/arm/boot/dts/qcom-msm8974pro.dtsi | 18 +
4 files changed, 674 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
create mode 100644 arch/arm/boot/dts/qcom-msm8974pro.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faf46abaa4a2..4da1b19178ec 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -701,6 +701,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-lge-nexus5-hammerhead.dtb \
+ qcom-msm8974-sony-xperia-castor.dtb \
qcom-msm8974-sony-xperia-honami.dtb \
qcom-mdm9615-wp8548-mangoh-green.dtb
dtb-$(CONFIG_ARCH_REALVIEW) += \
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
new file mode 100644
index 000000000000..e87f2c99060d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
@@ -0,0 +1,641 @@
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ model = "Sony Xperia Z2 Tablet";
+ compatible = "sony,xperia-castor", "qcom,msm8974";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ camera-snapshot {
+ label = "camera_snapshot";
+ gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA>;
+ };
+
+ camera-focus {
+ label = "camera_focus";
+ gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ };
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ smd {
+ rpm {
+ rpm_requests {
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-system-load = <154000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-system-load = <500000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_bl_vddio: lcd-backlight-vddio {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_bl_vddio";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+
+ gpio = <&msmgpio 69 0>;
+ enable-active-high;
+
+ vin-supply = <&pm8941_s3>;
+ startup-delay-us = <70000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_backlight_en_pin_a>;
+ };
+
+ vreg_vsp: lcd-dcdc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_vsp";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+
+ gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_dcdc_en_pin_a>;
+ };
+
+ vreg_wlan: wlan-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_regulator_pin>;
+ };
+};
+
+&soc {
+ sdhci at f9824900 {
+ status = "ok";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+ };
+
+ sdhci at f9864900 {
+ status = "ok";
+
+ max-frequency = <100000000>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf at 1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
+ };
+ };
+
+ sdhci at f98a4900 {
+ status = "ok";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ };
+
+ serial at f991e000 {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+ };
+
+ usb at f9a55000 {
+ status = "ok";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy at a {
+ status = "ok";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
+ };
+ };
+
+ pinctrl at fd510000 {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
+ };
+ };
+
+ i2c8_pins: i2c8 {
+ mux {
+ pins = "gpio47", "gpio48";
+ function = "blsp_i2c8";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ lcd_backlight_en_pin_a: lcd-backlight-vddio {
+ pins = "gpio69";
+ drive-strength = <10>;
+ output-low;
+ bias-disable;
+ };
+
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "gpio40";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "gpio39";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38";
+ function = "sdc3";
+
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ ts_int_pin: synaptics {
+ pin {
+ pins = "gpio86";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+ };
+ };
+
+ i2c at f9964000 {
+ status = "ok";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_pins>;
+
+ synaptics at 2c {
+ compatible = "syna,rmi-i2c";
+ reg = <0x2c>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_pin>;
+
+ rmi-f01 at 1 {
+ reg = <0x1>;
+ syna,nosleep = <1>;
+ };
+
+ rmi-f11 at 11 {
+ reg = <0x11>;
+ syna,f11-flip-x = <1>;
+ syna,sensor-type = <1>;
+ };
+ };
+ };
+
+ i2c at f9967000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ lp8566_wled: backlight at 2c {
+ compatible = "ti,lp8556";
+ reg = <0x2c>;
+ power-supply = <&vreg_bl_vddio>;
+
+ bl-name = "backlight";
+ dev-ctrl = /bits/ 8 <0x05>;
+ init-brt = /bits/ 8 <0x3f>;
+ rom_a0h {
+ rom-addr = /bits/ 8 <0xa0>;
+ rom-val = /bits/ 8 <0xff>;
+ };
+ rom_a1h {
+ rom-addr = /bits/ 8 <0xa1>;
+ rom-val = /bits/ 8 <0x3f>;
+ };
+ rom_a2h {
+ rom-addr = /bits/ 8 <0xa2>;
+ rom-val = /bits/ 8 <0x20>;
+ };
+ rom_a3h {
+ rom-addr = /bits/ 8 <0xa3>;
+ rom-val = /bits/ 8 <0x5e>;
+ };
+ rom_a4h {
+ rom-addr = /bits/ 8 <0xa4>;
+ rom-val = /bits/ 8 <0x02>;
+ };
+ rom_a5h {
+ rom-addr = /bits/ 8 <0xa5>;
+ rom-val = /bits/ 8 <0x04>;
+ };
+ rom_a6h {
+ rom-addr = /bits/ 8 <0xa6>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_a7h {
+ rom-addr = /bits/ 8 <0xa7>;
+ rom-val = /bits/ 8 <0xf7>;
+ };
+ rom_a9h {
+ rom-addr = /bits/ 8 <0xa9>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_aah {
+ rom-addr = /bits/ 8 <0xaa>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ rom_aeh {
+ rom-addr = /bits/ 8 <0xae>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pm8941 at 0 {
+ charger at 1000 {
+ qcom,fast-charge-safe-current = <1500000>;
+ qcom,fast-charge-current-limit = <1500000>;
+ qcom,dc-current-limit = <1800000>;
+ qcom,fast-charge-safe-voltage = <4400000>;
+ qcom,fast-charge-high-threshold-voltage = <4350000>;
+ qcom,fast-charge-low-threshold-voltage = <3400000>;
+ qcom,auto-recharge-threshold-voltage = <4200000>;
+ qcom,minimum-input-voltage = <4300000>;
+ };
+
+ gpios at c000 {
+ gpio_keys_pin_a: gpio-keys-active {
+ pins = "gpio2", "gpio5";
+ function = "normal";
+
+ bias-pull-up;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ wlan_sleep_clk_pin: wl-sleep-clk {
+ pins = "gpio17";
+ function = "func2";
+
+ output-high;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ wlan_regulator_pin: wl-reg-active {
+ pins = "gpio18";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ lcd_dcdc_en_pin_a: lcd-dcdc-en-active {
+ pins = "gpio20";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ input-disable;
+ output-low;
+ };
+
+ };
+
+ coincell at 2800 {
+ status = "ok";
+ qcom,rset-ohms = <2100>;
+ qcom,vset-millivolts = <3000>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index a39207625354..75cae87219d6 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -613,6 +613,20 @@
status = "disabled";
};
+ sdhci at f9864900 {
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+ interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
+ <GIC_SPI 224 IRQ_TYPE_NONE>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC3_APPS_CLK>,
+ <&gcc GCC_SDCC3_AHB_CLK>,
+ <&xo_board>;
+ clock-names = "core", "iface", "xo";
+ status = "disabled";
+ };
+
sdhci at f98a4900 {
compatible = "qcom,sdhci-msm-v4";
reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
new file mode 100644
index 000000000000..6740a4cb7da8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
@@ -0,0 +1,18 @@
+#include "qcom-msm8974.dtsi"
+
+/ {
+ soc {
+ sdhci at f9824900 {
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&xo_board>,
+ <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
+ <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
+ clock-names = "core", "iface", "xo", "cal", "sleep";
+ };
+
+ clock-controller at fc400000 {
+ compatible = "qcom,gcc-msm8974pro";
+ };
+ };
+};
--
2.12.0
More information about the linux-arm-kernel
mailing list