[PATCH 20/22] arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

[Simon Horman]

On Mon, Oct 02, 2017 at 01:18:49AM +0000, Yoshihiro Shimoda wrote:
> Hello,
> 
> > -----Original Message-----
> > From: Sergei Shtylyov
> > Sent: Saturday, September 30, 2017 7:24 PM
> > 
> > Hello!
> > 
> > On 9/29/2017 2:52 PM, Simon Horman wrote:
> > 
> > > From: Yoshihiro Shimoda <yoshihiro.shimoda.uh at renesas.com>
> > >
> > > This patch enables EthernetAVB for R-Car D3 draak board.
> > >
> > > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh at renesas.com>
> > > Reviewed-by: Geert Uytterhoeven <geert+renesas at glider.be>
> > > Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
> > > ---
> > >   arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
> > >   1 file changed, 25 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> > > index 7b776cb7e928..96b7ff5cc321 100644
> > > --- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> > > +++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> > [...]
> > > @@ -37,6 +39,14 @@
> > >   };
> > >
> > >   &pfc {
> > > +	avb0_pins: avb {
> > > +		mux {
> > > +			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",
> >                                                ^^^^^^^^^^^^^^
> >     Hum, I don't think it's compatible with routing the PHY interrupt via
> > GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.
> 
> Oops! You're correct. I should drop "avb0_phy_int".
> 
> Simon-san, may I send a follow-up patch to fix this?

Thanks Sergei, thanks Shimoda-san,

yes, please provide a follow-up patch.

At this stage I don't think we need to re-spin this pull-request
to fix this, rather a follow-up patch can be included
in a follow-up pull request.

> 
> Best regards,
> Yoshihiro Shimoda
> 
> > > +				 "avb0_mii";
> > > +			function = "avb0";
> > > +		};
> > > +	};
> > > +
> > >   	scif2_pins: scif2 {
> > >   		groups = "scif2_data";
> > >   		function = "scif2";
> > > @@ -56,6 +66,21 @@
> > >   	status = "okay";
> > >   };
> > >
> > > +&avb {
> > > +	pinctrl-0 = <&avb0_pins>;
> > > +	pinctrl-names = "default";
> > > +	renesas,no-ether-link;
> > > +	phy-handle = <&phy0>;
> > > +	status = "okay";
> > > +
> > > +	phy0: ethernet-phy at 0 {
> > > +		rxc-skew-ps = <1500>;
> > > +		reg = <0>;
> > > +		interrupt-parent = <&gpio5>;
> > > +		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> > > +	};
> > > +};
> > > +
> > >   &scif2 {
> > >   	pinctrl-0 = <&scif2_pins>;
> > >   	pinctrl-names = "default";
> > 
> > MBR, Sergei