[PATCH v4 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support

Wed Nov 29 16:43:43 PST 2017

On Wed, Nov 29, 2017 at 11:20:56AM +0100, Neil Armstrong wrote:
> This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
> SoM Carrier-Board.
> 
> This Carrier-Board has the following :
> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
> - HDMI Connector
> - USB Host + USB OTG Connector
> - 10/100/1000 Mbps Ethernet
> - miniPCI-Express slot
> - SD Card connector
> - Audio Headphone/Line In jack connectors
> - On-board DMIC
> - CAN bus header
> - SPI header
> - Camera Interfaces header
> - 4xButtons, 2xLeds
> - OnBoard RTC with Coin Backup battery socket
> - RS232 Header + USB-Serial debug port
> 
> Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
> 
> The board support is done with all on-board and header interfaces enabled.
> 7" LVDS Touchscreen is enabled by default along HDMI output.
> Audio interface is supported with the "simple-card" bindings.
> 
> PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
> 
> Reviewed-by: Fabio Estevam <fabio.estevam at nxp.com>
> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> ---
>  arch/arm/boot/dts/Makefile                     |   1 +
>  arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 239 +++++++++++++++++++++++++
>  2 files changed, 240 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index d0381e9..148ff15 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>  	imx6q-tx6q-11x0-mb7.dtb \
>  	imx6q-udoo.dtb \
>  	imx6q-utilite-pro.dtb \
> +	imx6q-var-dt6customboard.dtb \
>  	imx6q-wandboard.dtb \
>  	imx6q-wandboard-revb1.dtb \
>  	imx6q-wandboard-revd1.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> new file mode 100644
> index 0000000..76faaff
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
> @@ -0,0 +1,239 @@
> +/*
> + * Support for Variscite DART-MX6 Carrier-board
> + *
> + * Copyright 2017 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong at baylibre.com>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-var-dart.dtsi"
> +#include <dt-bindings/input/linux-event-codes.h>
> +
> +/ {
> +	model = "Variscite DART-MX6 Carrier-board";
> +	compatible = "variscite,dt6customboard", "fsl,imx6q";
> +
> +	backlight_lvds: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm2 0 50000>;
> +		brightness-levels = <0 4 8 16 32 64 128 248>;
> +		default-brightness-level = <7>;
> +		status = "okay";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		autorepeat;
> +
> +		back {
> +			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_BACK>;
> +			label = "Key Back";
> +			linux,input-type = <1>;
> +			debounce-interval = <100>;
> +			gpio-key,wakeup;

The gpio-key,wakeup is legacy one.  Use wakeup-source instead.

> +		};
> +
> +		home {
> +			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_HOME>;
> +			label = "Key Home";
> +			linux,input-type = <1>;
> +			debounce-interval = <100>;
> +			gpio-key,wakeup;
> +		};
> +
> +		menu {
> +			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_MENU>;
> +			label = "Key Menu";
> +			linux,input-type = <1>;
> +			debounce-interval = <100>;
> +			gpio-key,wakeup;
> +		};
> +	};
> +
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +
> +		led1 {
> +			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		led2 {
> +			gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +	};
> +
> +	panel1: lvds-panel {
> +		compatible = "sgd,gktw70sdae4se", "panel-lvds";
> +		backlight = <&backlight_lvds>;
> +
> +		width-mm = <153>;
> +		height-mm = <86>;
> +
> +		label = "gktw70sdae4se";
> +

Nit: these lines in middle of property list is not really necessary.
Can we drop them?

Shawn

> +		data-mapping = "jeida-18";
> +
> +		panel-timing {
> +			clock-frequency = <32000000>;
> +			hactive = <800>;
> +			vactive = <480>;
> +			hback-porch = <39>;
> +			hfront-porch = <39>;
> +			vback-porch = <29>;
> +			vfront-porch = <13>;
> +			hsync-len = <47>;
> +			vsync-len = <2>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&lvds1_out>;
> +			};
> +		};
> +	};
> +
> +	reg_usb_h1_vbus: regulator-usbh1vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_h1_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_usb_otg_vbus: regulator-usbotgvbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb_otg_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "dt6-customboard-audio";
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,bitclock-master = <&sound_codec>;
> +		simple-audio-card,frame-master = <&sound_codec>;
> +		simple-audio-card,widgets = "Headphone", "Headphone Jack",
> +					    "Line", "Line In";
> +		simple-audio-card,routing = "Headphone Jack", "HPLOUT",
> +					    "Headphone Jack", "HPROUT",
> +					    "LINE1L", "Line In",
> +					    "LINE1R", "Line In";
> +
> +		sound_cpu: simple-audio-card,cpu {
> +			sound-dai = <&ssi2>;
> +		};
> +
> +		sound_codec: simple-audio-card,codec {
> +			sound-dai = <&codec>;
> +			clocks = <&clks IMX6QDL_CLK_CKO>;
> +		};
> +	};
> +};
> +
> +&can1 {
> +	status = "okay";
> +};
> +
> +&ecspi1 {
> +	cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
> +		   <&gpio4 10 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&fec {
> +	status = "okay";
> +	phy-mode = "rgmii";
> +	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> +};
> +
> +&hdmi {
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	clock-frequency = <100000>;
> +	status = "okay";
> +
> +	touchscreen at 38 {
> +		compatible = "edt,edt-ft5x06";
> +		reg = <0x38>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> +		touchscreen-size-x = <800>;
> +		touchscreen-size-y = <480>;
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;
> +	};
> +
> +	rtc at 68 {
> +		compatible = "isil,isl12057";
> +		reg = <0x68>;
> +	};
> +};
> +
> +&ldb {
> +	status = "okay";
> +
> +	lvds-channel at 1 {
> +		status = "okay";
> +
> +		port at 4 {
> +			reg = <4>;
> +
> +			lvds1_out: endpoint {
> +				remote-endpoint = <&panel_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&pwm2 {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&reg_usb_h1_vbus>;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
> +	dr_mode = "otg";
> +	srp-disable;
> +	hnp-disable;
> +	adp-disable;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> -- 
> 2.7.4
> 