[PATCH v2 02/16] ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom
Russell King
rmk+kernel at armlinux.org.uk
Tue Nov 28 07:02:05 PST 2017
As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file. Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
---
arch/arm/boot/dts/imx6q-h100.dts | 1 -
arch/arm/boot/dts/imx6qdl-cubox-i.dtsi | 1 -
arch/arm/boot/dts/imx6qdl-hummingboard.dtsi | 1 -
arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi | 99 --------------------------
arch/arm/boot/dts/imx6qdl-microsom.dtsi | 53 ++++++++++++++
5 files changed, 53 insertions(+), 102 deletions(-)
delete mode 100644 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/imx6q-h100.dts
index a3269f57df2b..bf5dfc9c8127 100644
--- a/arch/arm/boot/dts/imx6q-h100.dts
+++ b/arch/arm/boot/dts/imx6q-h100.dts
@@ -43,7 +43,6 @@
#include "imx6q.dtsi"
#include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
/ {
model = "Auvidea H100";
diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
index b20508237046..57ce2dbb6ad9 100644
--- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
@@ -39,7 +39,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
index 0a0a7e4b956b..afd981e9b5e3 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
@@ -39,7 +39,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
/ {
chosen {
diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
deleted file mode 100644
index 900e8c781f91..000000000000
--- a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * Copyright (C) 2013,2014 Russell King
- *
- * This describes the hookup for an AR8035 to the iMX6 on the SolidRun
- * MicroSOM.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
- phy-mode = "rgmii";
- phy-reset-duration = <2>;
- phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&iomuxc {
- enet {
- pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
- fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- /* AR8035 reset */
- MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
- /* AR8035 interrupt */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x80000000
- /* GPIO16 -> AR8035 25MHz */
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0xc0000000
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x80000000
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
- /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1
- /* AR8035 pin strapping: IO voltage: pull up */
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- /* AR8035 pin strapping: PHYADDR#0: pull down */
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
- /* AR8035 pin strapping: PHYADDR#1: pull down */
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
- /* AR8035 pin strapping: MODE#1: pull up */
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- /* AR8035 pin strapping: MODE#3: pull up */
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- /* AR8035 pin strapping: MODE#0: pull down */
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
-
- /*
- * As the RMII pins are also connected to RGMII
- * so that an AR8030 can be placed, set these
- * to high-z with the same pulls as above.
- * Use the GPIO settings to avoid changing the
- * input select registers.
- */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000
- MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000
- >;
- };
- };
-};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom.dtsi b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
index f7266ae2534c..c1541f2ecf3a 100644
--- a/arch/arm/boot/dts/imx6qdl-microsom.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
@@ -69,6 +69,15 @@
};
};
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+ phy-mode = "rgmii";
+ phy-reset-duration = <2>;
+ phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
&iomuxc {
microsom {
pinctrl_microsom_brcm_bt: microsom-brcm-bt {
@@ -100,6 +109,50 @@
>;
};
+ pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ /* AR8035 reset */
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
+ /* AR8035 interrupt */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x80000000
+ /* GPIO16 -> AR8035 25MHz */
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0xc0000000
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x80000000
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1
+ /* AR8035 pin strapping: IO voltage: pull up */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ /* AR8035 pin strapping: PHYADDR#0: pull down */
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
+ /* AR8035 pin strapping: PHYADDR#1: pull down */
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
+ /* AR8035 pin strapping: MODE#1: pull up */
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ /* AR8035 pin strapping: MODE#3: pull up */
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ /* AR8035 pin strapping: MODE#0: pull down */
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
+
+ /*
+ * As the RMII pins are also connected to RGMII
+ * so that an AR8030 can be placed, set these
+ * to high-z with the same pulls as above.
+ * Use the GPIO settings to avoid changing the
+ * input select registers.
+ */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000
+ >;
+ };
+
pinctrl_microsom_uart1: microsom-uart1 {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
--
2.7.4
More information about the linux-arm-kernel
mailing list