[PATCH 46/58] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
Alexandre Belloni
alexandre.belloni at free-electrons.com
Tue May 30 14:51:27 PDT 2017
Add a driver for the Atmel Timer Counter Blocks. This driver provides a
clocksource and a clockevent device. The clockevent device is linked to the
clocksource counter and so it will run at the same frequency.
This driver uses regmap and syscon to be able to probe early in the boot
and avoid having to switch on the TCB clocksource later. Using regmap also
means that unused TCB channels may be used by other drivers (PWM for
example).
Cc: Daniel Lezcano <daniel.lezcano at linaro.org>
Cc: Thomas Gleixner <tglx at linutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
---
drivers/clocksource/Kconfig | 13 ++
drivers/clocksource/Makefile | 3 +-
drivers/clocksource/timer-atmel-tcbclksrc.c | 252 ++++++++++++++++++++++++++++
3 files changed, 267 insertions(+), 1 deletion(-)
create mode 100644 drivers/clocksource/timer-atmel-tcbclksrc.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 545d541ae20e..cbd710db3c09 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -418,6 +418,19 @@ config ATMEL_ST
help
Support for the Atmel ST timer.
+config ATMEL_ARM_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ select REGMAP_MMIO
+ depends on GENERIC_CLOCKEVENTS
+ depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5 || COMPILE_TEST
+ default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate.
+ On platforms with 16-bit counters, two timer channels are combined
+ to make a single 32-bit timer.
+ It can also be used as a clock event device supporting oneshot mode.
+
config CLKSRC_METAG_GENERIC
def_bool y if METAG
help
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 2b5b56a6f00f..53a0b40e0db2 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -2,7 +2,8 @@ obj-$(CONFIG_CLKSRC_PROBE) += clksrc-probe.o
obj-$(CONFIG_CLKEVT_PROBE) += clkevt-probe.o
obj-$(CONFIG_ATMEL_PIT) += timer-atmel-pit.o
obj-$(CONFIG_ATMEL_ST) += timer-atmel-st.o
-obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
+obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
+obj-$(CONFIG_ATMEL_ARM_TCB_CLKSRC) += timer-atmel-tcbclksrc.o
obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o
obj-$(CONFIG_SCx200HR_TIMER) += scx200_hrt.o
obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC) += cs5535-clockevt.o
diff --git a/drivers/clocksource/timer-atmel-tcbclksrc.c b/drivers/clocksource/timer-atmel-tcbclksrc.c
new file mode 100644
index 000000000000..f18d177bfdea
--- /dev/null
+++ b/drivers/clocksource/timer-atmel-tcbclksrc.c
@@ -0,0 +1,252 @@
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/sched_clock.h>
+#include <soc/at91/atmel_tcb.h>
+
+static struct atmel_tcb_clksrc {
+ char name[20];
+ struct clocksource clksrc;
+ struct regmap *regmap;
+ struct clk *clk[2];
+ int channels[2];
+ int bits;
+ int irq;
+ bool registered;
+} tc = {
+ .clksrc = {
+ .rating = 200,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+ },
+};
+
+static u64 tc_get_cycles(struct clocksource *cs)
+{
+ u32 lower, upper, tmp;
+
+ do {
+ regmap_read(tc.regmap, ATMEL_TC_CV(1), &upper);
+ regmap_read(tc.regmap, ATMEL_TC_CV(0), &lower);
+ regmap_read(tc.regmap, ATMEL_TC_CV(1), &tmp);
+ } while (upper != tmp);
+
+ return (upper << 16) | lower;
+}
+
+static u64 tc_get_cycles32(struct clocksource *cs)
+{
+ u32 val;
+
+ regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
+
+ return val;
+}
+
+static u64 notrace tc_sched_clock_read(void)
+{
+ return tc_get_cycles(&tc.clksrc);
+}
+
+static u64 notrace tc_sched_clock_read32(void)
+{
+ return tc_get_cycles32(&tc.clksrc);
+}
+
+static void __init tcb_setup_dual_chan(struct atmel_tcb_clksrc *tc,
+ int mck_divisor_idx)
+{
+ /* first channel: waveform mode, input mclk/8, clock TIOA on overflow */
+ regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[0]),
+ mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_CMR_WAVE
+ | ATMEL_TC_CMR_WAVESEL_UP /* free-run */
+ | ATMEL_TC_CMR_ACPA(SET) /* TIOA rises at 0 */
+ | ATMEL_TC_CMR_ACPC(CLEAR)); /* (duty cycle 50%) */
+ regmap_write(tc->regmap, ATMEL_TC_RA(tc->channels[0]), 0x0000);
+ regmap_write(tc->regmap, ATMEL_TC_RC(tc->channels[0]), 0x8000);
+ regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[0]), 0xff); /* no irqs */
+ regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[0]),
+ ATMEL_TC_CCR_CLKEN);
+
+ /* second channel: waveform mode, input TIOA */
+ regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[1]),
+ ATMEL_TC_CMR_XC(tc->channels[1]) /* input: TIOA */
+ | ATMEL_TC_CMR_WAVE
+ | ATMEL_TC_CMR_WAVESEL_UP); /* free-run */
+ regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[1]), 0xff); /* no irqs */
+ regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[1]),
+ ATMEL_TC_CCR_CLKEN);
+
+ /* chain both channel, we assume the previous channel */
+ regmap_write(tc->regmap, ATMEL_TC_BMR,
+ ATMEL_TC_BMR_TCXC(1 + tc->channels[1], tc->channels[1]));
+ /* then reset all the timers */
+ regmap_write(tc->regmap, ATMEL_TC_BCR, ATMEL_TC_BCR_SYNC);
+}
+
+static void __init tcb_setup_single_chan(struct atmel_tcb_clksrc *tc,
+ int mck_divisor_idx)
+{
+ /* channel 0: waveform mode, input mclk/8 */
+ regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[0]),
+ mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_CMR_WAVE
+ | ATMEL_TC_CMR_WAVESEL_UP /* free-run */
+ );
+ regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[0]), 0xff); /* no irqs */
+ regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[0]),
+ ATMEL_TC_CCR_CLKEN);
+
+ /* then reset all the timers */
+ regmap_write(tc->regmap, ATMEL_TC_BCR, ATMEL_TC_BCR_SYNC);
+}
+
+static int __init tcb_clksrc_register(struct device_node *node,
+ struct regmap *regmap, int channel,
+ int channel1, int irq, int bits)
+{
+ u32 rate, divided_rate = 0;
+ int best_divisor_idx = -1;
+ int i, err = -1;
+ u64 (*tc_sched_clock)(void);
+
+ tc.regmap = regmap;
+ tc.channels[0] = channel;
+ tc.channels[1] = channel1;
+ tc.irq = irq;
+ tc.bits = bits;
+
+ tc.clk[0] = tcb_clk_get(node, tc.channels[0]);
+ if (IS_ERR(tc.clk[0]))
+ return PTR_ERR(tc.clk[0]);
+ err = clk_prepare_enable(tc.clk[0]);
+ if (err) {
+ pr_debug("can't enable T0 clk\n");
+ goto err_clk;
+ }
+
+ /* How fast will we be counting? Pick something over 5 MHz. */
+ rate = (u32)clk_get_rate(tc.clk[0]);
+ for (i = 0; i < 5; i++) {
+ unsigned int divisor = atmel_tc_divisors[i];
+ unsigned int tmp;
+
+ if (!divisor)
+ continue;
+
+ tmp = rate / divisor;
+ pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
+ if (best_divisor_idx > 0) {
+ if (tmp < 5 * 1000 * 1000)
+ continue;
+ }
+ divided_rate = tmp;
+ best_divisor_idx = i;
+ }
+
+ if (tc.bits == 32) {
+ tc.clksrc.read = tc_get_cycles32;
+ tcb_setup_single_chan(&tc, best_divisor_idx);
+ tc_sched_clock = tc_sched_clock_read32;
+ snprintf(tc.name, sizeof(tc.name), "%s:%d",
+ kbasename(node->parent->full_name), tc.channels[0]);
+ } else {
+ tc.clk[1] = tcb_clk_get(node, tc.channels[1]);
+ if (IS_ERR(tc.clk[1]))
+ goto err_disable_t0;
+
+ err = clk_prepare_enable(tc.clk[1]);
+ if (err) {
+ pr_debug("can't enable T1 clk\n");
+ goto err_clk1;
+ }
+ tc.clksrc.read = tc_get_cycles,
+ tcb_setup_dual_chan(&tc, best_divisor_idx);
+ tc_sched_clock = tc_sched_clock_read;
+ snprintf(tc.name, sizeof(tc.name), "%s:%d,%d",
+ kbasename(node->parent->full_name), tc.channels[0],
+ tc.channels[1]);
+ }
+
+ pr_debug("%s at %d.%03d MHz\n", tc.name,
+ divided_rate / 1000000,
+ ((divided_rate + 500000) % 1000000) / 1000);
+
+ tc.clksrc.name = tc.name;
+
+ err = clocksource_register_hz(&tc.clksrc, divided_rate);
+ if (err)
+ goto err_disable_t1;
+
+ sched_clock_register(tc_sched_clock, 32, divided_rate);
+
+ tc.registered = true;
+
+ return 0;
+
+err_disable_t1:
+ if (tc.bits == 16)
+ clk_disable_unprepare(tc.clk[1]);
+
+err_clk1:
+ if (tc.bits == 16)
+ clk_put(tc.clk[1]);
+
+err_disable_t0:
+ clk_disable_unprepare(tc.clk[0]);
+
+err_clk:
+ clk_put(tc.clk[0]);
+
+ pr_err("%s: unable to register clocksource/clockevent\n",
+ tc.clksrc.name);
+
+ return err;
+}
+
+static int __init tcb_clksrc_init(struct device_node *node)
+{
+ const struct of_device_id *match;
+ const struct atmel_tcb_info *tcb_info;
+ struct regmap *regmap;
+ u32 channel;
+ int bits, irq, err, chan1 = -1;
+
+ if (tc.registered)
+ return -ENODEV;
+
+ regmap = syscon_node_to_regmap(node->parent);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ match = of_match_node(atmel_tcb_dt_ids, node->parent);
+ tcb_info = match->data;
+ bits = tcb_info->bits;
+
+ err = of_property_read_u32_index(node, "reg", 0, &channel);
+ if (err)
+ return err;
+
+ irq = tcb_irq_get(node, channel);
+ if (irq < 0)
+ return irq;
+
+ if (bits == 16) {
+ of_property_read_u32_index(node, "reg", 1, &chan1);
+ if (chan1 == -1) {
+ pr_err("%s: clocksource needs two channels\n",
+ node->parent->full_name);
+ return -EINVAL;
+ }
+ }
+
+ return tcb_clksrc_register(node, regmap, channel, chan1, irq, bits);
+}
+CLOCKSOURCE_OF_DECLARE(atmel_tcb_clksrc, "atmel,tcb-timer",
+ tcb_clksrc_init);
--
2.11.0
More information about the linux-arm-kernel
mailing list