Device address specific mapping of arm,mmu-500

[Ray Jui]

Hi Marc,

On 5/30/17 9:59 AM, Marc Zyngier wrote:
> On 30/05/17 17:49, Ray Jui wrote:
>> Hi Will,
>>
>> On 5/30/17 8:14 AM, Will Deacon wrote:
>>> On Mon, May 29, 2017 at 06:18:45PM -0700, Ray Jui wrote:
>>>> I'm writing to check with you to see if the latest arm-smmu.c driver in
>>>> v4.12-rc Linux for smmu-500 can support mapping that is only specific to
>>>> a particular physical address range while leave the rest still to be
>>>> handled by the client device. I believe this can already be supported by
>>>> the device tree binding of the generic IOMMU framework; however, it is
>>>> not clear to me whether or not the arm-smmu.c driver can support it.
>>>>
>>>> To give you some background information:
>>>>
>>>> We have a SoC that has PCIe root complex that has a build-in logic block
>>>> to forward MSI writes to ARM GICv3 ITS. Unfortunately, this logic block
>>>> has a HW bug that causes the MSI writes not parsed properly and can
>>>> potentially corrupt data in the internal FIFO. A workaround is to have
>>>> ARM MMU-500 takes care of all inbound transactions. I found that is
>>>> working after hooking up our PCIe root complex to MMU-500; however, even
>>>> with this optimized arm-smmu driver in v4.12, I'm still seeing a
>>>> significant Ethernet throughput drop in both the TX and RX directions.
>>>> The throughput drop is very significant at around 50% (but is already
>>>> much improved compared to other prior kernel versions at 70~90%).
>>>
>>> Did Robin's experiments help at all with this?
>>>
>>> http://www.linux-arm.org/git?p=linux-rm.git;a=shortlog;h=refs/heads/iommu/perf
>>>
>>
>> It looks like these are new optimizations that have not yet been merged
>> in v4.12? I'm going to give it a try.
>>
>>>> One alternative is to only use MMU-500 for MSI writes towards
>>>> GITS_TRANSLATER register in the GICv3, i.e., if I can define a specific
>>>> region of physical address that I want MMU-500 to act on and leave the
>>>> rest of inbound transactions to be handled directly by our PCIe
>>>> controller, it can potentially work around the HW bug we have and at the
>>>> same time achieve optimal throughput.
>>>
>>> I don't think you can bypass the SMMU for MSIs unless you give them their
>>> own StreamIDs, which is likely to break things horribly in the kernel. You
>>> could try to create an identity mapping, but you'll still have the
>>> translation overhead and you'd probably end up having to supply your own DMA
>>> ops to manage the address space. I'm assuming that you need to prevent the
>>> physical address of the ITS from being allocated as an IOVA?
>>
>> Will, is that a HW limitation that the SMMU cannot be used, only for MSI
>> writes, in which case, the physical address range is very specific in
>> our ASIC that falls in the device memory region (e.g., below 0x80000000)?
>>
>> In fact, what I need in this case is a static mapping from IOMMU on the
>> physical address of the GITS_TRANSLATER of the GICv3 ITS, which is the
>> address that MSI writes go to. This is to bypass the MSI forwarding
>> logic in our PCIe controller. At the same time, I can leave the rest of
>> inbound transactions to be handled by our PCIe controller without going
>> through the MMU.
> 
> How is that going to work for DMA? I imagine your network interfaces do
> have to access memory, don't they? How can the transactions be
> terminated in the PCIe controller?

Sorry, I may not phrase this properly. These inbound transactions (DMA
write to DDR, from endpoint) do not terminate in the PCIe controller.
They are taken by the PCIe controller as PCIe transactions and will be
carried towards the designated memory on the host.

> 
> Thanks,
> 
> 	M.
>