[PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
Chen-Yu Tsai
wens at csie.org
Mon May 29 06:25:44 PDT 2017
On Mon, May 29, 2017 at 9:19 PM, <icenowy at aosc.io> wrote:
> 在 2017-05-29 21:11，Chen-Yu Tsai 写道：
>>
>> On Sat, May 27, 2017 at 06:23:04PM +0800, Icenowy Zheng wrote:
>>>
>>> R40 is said to be an upgrade of A20, and its pin configuration is also
>>> similar to A20 (and thus similar to A10).
>>>
>>> Add support for R40 to the A10 pinctrl driver.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>>> ---
>>> drivers/pinctrl/sunxi/Kconfig | 2 +-
>>> drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 272
>>> +++++++++++++++++++++---------
>>> 2 files changed, 197 insertions(+), 77 deletions(-)
>>>
>>> diff --git a/drivers/pinctrl/sunxi/Kconfig
>>> b/drivers/pinctrl/sunxi/Kconfig
>>> index 624d84e6c936..9d01da3b90bd 100644
>>> --- a/drivers/pinctrl/sunxi/Kconfig
>>> +++ b/drivers/pinctrl/sunxi/Kconfig
>>> @@ -7,7 +7,7 @@ config PINCTRL_SUNXI
>>> select GPIOLIB
>>>
>>> config PINCTRL_SUN4I_A10
>>> - def_bool MACH_SUN4I || MACH_SUN7I
>>> + def_bool MACH_SUN4I || MACH_SUN7I || MACH_SUN8I
>>> select PINCTRL_SUNXI
>>>
>>> config PINCTRL_SUN5I
>>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> index 159580c04b14..0f6ca8391ea7 100644
>>> --- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>
>>
>> [...]
>>
>>> @@ -162,14 +183,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION(0x3, "can"), /* RX */
>>> SUNXI_FUNCTION(0x4, "uart1"), /* RING */
>>> SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR
>>> */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40)),
>>> /* Hole */
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
>>> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
>>> + SUNXI_FUNCTION_VARIANT(0x3,
>>> + "pll-lock-dbg",
>>
>>
>> Can you stick to underscores to be consistent?
>
>
> OK...
> This is a so strange pin name and I just picked the datasheet
> name.
>
> I don't care how to name it as I don't even know what this is.
>
>
>>
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> @@ -177,11 +203,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
>>> + SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20),
>>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "ir0"), /* TX */
>>> + SUNXI_FUNCTION_VARIANT(0x2, "ir0", /* TX */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20),
>>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm0", /* PWM1 */
>>
>>
>> The numbering is wrong. Just drop the number altogether, like all the
>> other instances.
>>
>>> + PINCTRL_SUN8I_R40),
>>> /*
>>> * The SPDIF block is not referenced at all in the A10
>>> user
>>> * manual. However it is described in the code leaked and
>>> the
>>> @@ -205,7 +239,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] =
>>> {
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>
>>
>> Maybe we could use "i2s" instead, like on the A10. I don't know where
>> i2s1 is used, but it certainly isn't routed outside the SoC, and i2s2
>> looks like it's for dw-hdmi's audio path.
>
>
> Nope, it's routed at PA bank, see pins start at PA14.
>
> Changing this name will also break existing A20 device trees, if any of
> them use I2S.
Missed that one. Sorry about the noise.
>
>
>>
>>> SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>
>>
>> [...]
>>
>>> @@ -237,31 +275,41 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM6 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM7 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> SUNXI_FUNCTION(0x3, "ac97"), /* DI */
>>> /* Undocumented mux function on A10 - See SPDIF MCLK
>>> above */
>>> - SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
>>> + SUNXI_FUNCTION_VARIANT(0x4, "spdif", /* SPDIF IN */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> @@ -308,7 +356,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] =
>>> {
>>
>>
>> You missed PWM4 and PWM5 on pins PB20 and PB21.
>>
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION(0x2, "uart0"), /* TX */
>>> - SUNXI_FUNCTION(0x3, "ir1")), /* TX */
>>> + SUNXI_FUNCTION_VARIANT(0x3, "ir1", /* TX */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>
>>
>> [...]
>>
>>> @@ -916,7 +1000,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x5, "sim", /* DET */
>>> + PINCTRL_SUN8I_R40),
>>
>>
>> This is available on all 3 variants.
>>
>> Should we consider sending a fix for this first? The hardware backing
>> this pin is not supported, but it would be less confusing to fix it
>> first instead of introducing a function for all variants in a patch
>> supposedly for just the R40.
>
>
> OK.
>
> But if we do so I think I should delay this patch until the A10-A20
> driver merge is applied...
Since the hardware is unsupported to begin with, I think that's OK.
You could add an extra patch just before this one in the series.
ChenYu
>
>>
>>> SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
>>> SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
>>> SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
>>
>>
>> [...]
>>
>> Looks good otherwise.
>>
>>
>> Regards
>> ChenYu
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list