[linux-sunxi] [PATCH 1/3] arm64: allwinner: a64: Add initial Orangepi Win/WinPlus support
Icenowy Zheng
icenowy at aosc.io
Fri May 26 02:03:17 PDT 2017
于 2017年5月26日 GMT+08:00 下午4:59:18, Andre Przywara <andre.przywara at arm.com> 写到:
>Hi,
>
>On 26/05/17 04:54, Chen-Yu Tsai wrote:
>> On Fri, May 26, 2017 at 6:30 AM, André Przywara
><andre.przywara at arm.com> wrote:
>>> On 25/05/17 20:26, Jagan Teki wrote:
>>>> From: Jagan Teki <jagan at amarulasolutions.com>
>>>>
>>>> Orangepi Win/WinPlus is an open-source single-board computer
>>>> using the Allwinner A64 SOC.
>>>>
>>>> A64 Orangepi Win/WinPlus has
>>>> - A64 Quad-core Cortex-A53 64bit
>>>> - 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
>>>> - Debug TTL UART
>>>> - Four USB 2.0
>>>
>>> I take it those are connected to a hub chip, and the micro-USB
>socket is
>>> connected as a true OTG socket?
>>> So you should enable the usb_otg node, but without the host mode
>>> override we use for the Pine64.
>>
>> Agreed. Unless OTG needs PMIC support.
>
>Ah, good point. Quickly looking at the schematics [1] I see that
>something's wrong there - could be me as well ...
>
>The OTG port has a voltage regulator enabled by USB0-DRVVBUS, which
>seems to be connected to GPIO PD7, according to the GPIO assignment
>table.
>Each of the dual-socket host port pairs (connected to the HUB) have a
>separate voltage regulator, ports 3 and 4 seems to be always enabled,
>whereas ports 1 and 2 are controlled by the USB1-DRVVBUS signal.
>Now this signal seems to be connected to PD7 as well, but this time
>directly on the schematic, not in the table.
>
>So either there is only one signal, connected to PD7, or one of the
>lines is connected to another GPIO.
>
>One could try to play around with PD7 in Linux and measure the voltage
>on all the 5 USB connectors to shed some light on this.
Oh I found a problem here -- I seems to forget to enable vbus
detection and drivevbus on AXP803...
Let me add them in further patches.
I have a BPI M64, which has real OTG port.
>
>>>> - HDMI
>>>> - LCD
>>>> - Audio and MIC
>>>> - Wifi + BT
>>>
>>> It looks like Wifi + BT are soldered on the board, so you should at
>>> least enable the proper UART connected to the Bluetooth chip,
>probably
>>> also MMC1 (which is surely connected to the WiFi chip) should be
>>> described as an SDIO node.
>>
>> Those probably need regulator support. Having them enabled together
>> might be better.
>
>Good point, seems like DLDO4 and DLDO2 are responsible for this.
>
>>>
>>>> - IR receiver
>>>> - 5V DC power supply
>>>
>>> I guess the board uses the AXP803 as well? You might want to
>coordinate
>>> with Icenowy what to do to describe this as well, given that her
>patches
>>> might go in before.
>>
>> Still waiting for NMI driver/bindings to be merged before I merge the
>dts
>> file changes. The mfd and regulator driver changes are already in
>-next.
>>
>>>
>>> Cheers,
>>> Andre.
>>>
>>>> http://www.orangepi.org/OrangePiWin_WinPlus/
>>
>> The URL is not going to be helpful if it goes offline.
>>
>> Can someone provide schematics for this board? Without it there's
>really
>> no verification for what the device tree describes.
>
>Found them here [1].
>
>>>>
>>>> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
>>>> ---
>>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>>>> .../boot/dts/allwinner/sun50i-a64-orangepi-win.dts | 102
>+++++++++++++++++++++
>>>> 2 files changed, 103 insertions(+)
>>>> create mode 100644
>arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
>>>>
>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile
>b/arch/arm64/boot/dts/allwinner/Makefile
>>>> index 244e8b7..4120ce9 100644
>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>>> @@ -1,5 +1,6 @@
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb
>sun50i-a64-pine64.dtb
>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>>>>
>>>> always := $(dtb-y)
>>>> diff --git
>a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
>b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
>>>> new file mode 100644
>>>> index 0000000..b16e606
>>>> --- /dev/null
>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
>>>> @@ -0,0 +1,102 @@
>>>> +/*
>>>> + * Copyright (C) 2017 Jagan Teki <jteki at openedev.com>
>>>> + *
>>>> + * This file is dual-licensed: you can use it either under the
>terms
>>>> + * of the GPL or the X11 license, at your option. Note that this
>dual
>>>> + * licensing only applies to this file, and not this project as a
>>>> + * whole.
>>>> + *
>>>> + * a) This library is free software; you can redistribute it
>and/or
>>>> + * modify it under the terms of the GNU General Public License
>as
>>>> + * published by the Free Software Foundation; either version 2
>of the
>>>> + * License, or (at your option) any later version.
>>>> + *
>>>> + * This library is distributed in the hope that it will be
>useful,
>>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty
>of
>>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
>the
>>>> + * GNU General Public License for more details.
>>>> + *
>>>> + * Or, alternatively,
>>>> + *
>>>> + * b) Permission is hereby granted, free of charge, to any person
>>>> + * obtaining a copy of this software and associated
>documentation
>>>> + * files (the "Software"), to deal in the Software without
>>>> + * restriction, including without limitation the rights to
>use,
>>>> + * copy, modify, merge, publish, distribute, sublicense,
>and/or
>>>> + * sell copies of the Software, and to permit persons to whom
>the
>>>> + * Software is furnished to do so, subject to the following
>>>> + * conditions:
>>>> + *
>>>> + * The above copyright notice and this permission notice shall
>be
>>>> + * included in all copies or substantial portions of the
>Software.
>>>> + *
>>>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
>KIND,
>>>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
>WARRANTIES
>>>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>>>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>>>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
>LIABILITY,
>>>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
>ARISING
>>>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
>OR
>>>> + * OTHER DEALINGS IN THE SOFTWARE.
>>>> + */
>>>> +
>>>> +/dts-v1/;
>>>> +
>>>> +#include "sun50i-a64.dtsi"
>>>> +
>>>> +#include <dt-bindings/gpio/gpio.h>
>>>> +
>>>> +/ {
>>>> + model = "OrangePi Win/Win Plus";
>>>> + compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64";
>>>> +
>>>> + aliases {
>>>> + serial0 = &uart0;
>>>> + };
>>>> +
>>>> + chosen {
>>>> + stdout-path = "serial0:115200n8";
>>>> + };
>>>> +
>>>> + soc {
>>>> + reg_vcc3v3: vcc3v3 {
>>>> + compatible = "regulator-fixed";
>>>> + regulator-name = "vcc3v3";
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + };
>>
>> This should be outside of the soc node.
>
>Agreed on that one.
>
>> Furthermore, you should
>> not be doing full path overrides in the dts file. If you need
>> to reference a node, but it doesn't have a label, add the label
>> first.
>
>That shouldn't be needed if it's outside of the /soc node?
>
>>>> + };
>>>> +};
>>>> +
>>>> +&mmc0 {
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&mmc0_pins>;
>>>> + vmmc-supply = <®_vcc3v3>;
>>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
>>
>> Please add a comment after this denoting the pin name.
>>
>>>> + cd-inverted;
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +&uart0 {
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&uart0_pins_a>;
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +&i2c1 {
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&i2c1_pins>;
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +&usbphy {
>>>> + status = "okay";
>>
>> No VBUS regulator supplies?
>
>The HSIC block in the SoC needs apparently to be driven by FLDO1.
>The voltage regulator for two of the USB host ports is enabled by PD7
>(or not, see above).
>
>> Does the USB hub need a node?
>
>Good question, given that two of the ports have their bus power
>switchable, while the other two are always enabled. Do we express those
>things in the DT?
>
>Cheers,
>Andre.
>
>[1] http://www.orangepi.org/download/ORANGEPI-WIN-V1_1.pdf
>http://www.orangepi.org/download/ORANGEPI-Winplus-V1_3.pdf
>http://www.orangepi.org/downloadresources/
>
>Can someone (without commercial and legal conflict potential) please
>upload them to the sunxi Wiki?
>
>>
>> Regards
>> ChenYu
>>
>>>> +};
>>>> +
>>>> +&ohci1 {
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +&ehci1 {
>>>> + status = "okay";
>>>> +};
>>>>
>>>
More information about the linux-arm-kernel
mailing list