[linux-sunxi] [PATCH 1/2] ARM: sun8i: v3s: add device nodes for DE2 display pipeline

[Chen-Yu Tsai]

On Thu, May 25, 2017 at 9:54 PM, Icenowy Zheng <icenowy at aosc.io> wrote:
>
>
> 于 2017年5月25日 GMT+08:00 下午4:37:31, Chen-Yu Tsai <wens at csie.org> 写到:
>>On Wed, May 24, 2017 at 7:17 PM, Icenowy Zheng <icenowy at aosc.io> wrote:
>>> Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
>>> and only one TCON connected to this mixer, which have RGB LCD output.
>>>
>>> Add device nodes for this display pipeline.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>>> ---
>>>  arch/arm/boot/dts/sun8i-v3s.dtsi | 83
>>++++++++++++++++++++++++++++++++++++++++
>>>  1 file changed, 83 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi
>>b/arch/arm/boot/dts/sun8i-v3s.dtsi
>>> index a49ebef53c91..3a06dc5b3746 100644
>>> --- a/arch/arm/boot/dts/sun8i-v3s.dtsi
>>> +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
>>> @@ -61,6 +61,12 @@
>>>                 };
>>>         };
>>>
>>> +       de: display-engine {
>>> +               compatible = "allwinner,sun8i-v3s-display-engine";
>>> +               allwinner,pipelines = <&mixer0>;
>>> +               status = "disabled";
>>> +       };
>>> +
>>>         timer {
>>>                 compatible = "arm,armv7-timer";
>>>                 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
>>IRQ_TYPE_LEVEL_LOW)>,
>>> @@ -95,6 +101,83 @@
>>>                 #size-cells = <1>;
>>>                 ranges;
>>>
>>> +               display_clocks: clock at 1000000 {
>>> +                       compatible = "allwinner,sun8i-v3s-de2-clk";
>>> +                       reg = <0x01000000 0x100000>;
>>> +                       clocks = <&ccu CLK_DE>,
>>> +                                <&ccu CLK_BUS_DE>;
>>> +                       clock-names = "mod",
>>> +                                     "bus";
>>> +                       resets = <&ccu RST_BUS_DE>;
>>> +                       #clock-cells = <1>;
>>> +                       #reset-cells = <1>;
>>> +               };
>>> +
>>> +               mixer0: mixer at 1100000 {
>>
>>Since there's only one, can you drop the numbering suffix?
>>Same with the TCON.
>
> I just want to keep the consistency with dual-pipeline SoCs. (H3, A64, H5, etc)
>
> However, if dropping it is better, I will drop it -- I think usually for things
> that is available for multiple on some SoCs and single on others,
> we keep the 0 in node name...

You might want that if you were going to include it in another SoC's dtsi
file, such as the situation with A23/A33. However that is not the case here.
Moreover, the datasheet lists them without the number.

>
>>
>>> +                       compatible = "allwinner,sun8i-v3s-de2-mixer";
>>> +                       reg = <0x01100000 0x100000>;
>>
>>The display engine also has an interrupt. Please list it
>
> It's a overall interrupt for DE2, not mixer interrupt.
>
> I will add it after we have proper interrupt chaining facility for DE2.
>
> It cannot fit here in mixer node.

Could you elaborate? If it is just shared, then listing it several times
is OK. If the interrupt registers are not in this address space, then
I agree, it needs to be dealt with separately and not added here. However
some thought should be given about how the device tree binding should be.

ChenYu

>
>>
>>ChenYu
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.