[linux-sunxi] [RFC PATCH 10/11] ARM: sun8i: h3: add display engine pipeline for TVE
Chen-Yu Tsai
wens at csie.org
Tue May 23 22:34:58 PDT 2017
On Wed, May 24, 2017 at 1:28 PM, Icenowy Zheng <icenowy at aosc.io> wrote:
>
>
> 于 2017年5月24日 GMT+08:00 下午1:24:29, Chen-Yu Tsai <wens at csie.org> 写到:
>>On Thu, May 18, 2017 at 12:43 AM, Icenowy Zheng <icenowy at aosc.io>
>>wrote:
>>> As we have already the support for the TV encoder on Allwinner H3,
>>add
>>> the display engine pipeline device tree nodes to its DTSI file.
>>>
>>> The H5 pipeline has some differences and will be enabled later.
>>>
>>> The currently-unused mixer0 and tcon0 are also needed, for the
>>> completement of the pipeline.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>>> ---
>>> arch/arm/boot/dts/sun8i-h3.dtsi | 189
>>++++++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 189 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi
>>b/arch/arm/boot/dts/sun8i-h3.dtsi
>>> index b36f9f423c39..20172ef92415 100644
>>> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
>>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>>> @@ -41,6 +41,8 @@
>>> */
>>>
>>> #include "sunxi-h3-h5.dtsi"
>>> +#include <dt-bindings/clock/sun8i-de2.h>
>>> +#include <dt-bindings/reset/sun8i-de2.h>
>>>
>>> / {
>>> cpus {
>>> @@ -72,6 +74,193 @@
>>> };
>>> };
>>>
>>> + de: display-engine {
>>> + compatible = "allwinner,sun8i-h3-display-engine";
>>> + allwinner,pipelines = <&mixer0>,
>>> + <&mixer1>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + soc {
>>> + display_clocks: clock at 1000000 {
>>> + compatible = "allwinner,sun8i-a83t-de2-clk";
>>> + reg = <0x01000000 0x100000>;
>>> + clocks = <&ccu CLK_BUS_DE>,
>>> + <&ccu CLK_DE>;
>>> + clock-names = "bus",
>>> + "mod";
>>> + resets = <&ccu RST_BUS_DE>;
>>> + #clock-cells = <1>;
>>> + #reset-cells = <1>;
>>> + assigned-clocks = <&ccu CLK_DE>;
>>> + assigned-clock-parents = <&ccu CLK_PLL_DE>;
>>> + assigned-clock-rates = <432000000>;
>>> + };
>>> +
>>> + mixer0: mixer at 1100000 {
>>> + compatible = "allwinner,sun8i-h3-de2-mixer0";
>>> + reg = <0x01100000 0x100000>;
>>> + clocks = <&display_clocks CLK_BUS_MIXER0>,
>>> + <&display_clocks CLK_MIXER0>;
>>> + clock-names = "bus",
>>> + "mod";
>>> + resets = <&display_clocks RST_MIXER0>;
>>> + status = "disabled";
>>> +
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + mixer0_out: port at 1 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <1>;
>>> +
>>> + mixer0_out_tcon0: endpoint at 0
>>{
>>> + reg = <0>;
>>> + remote-endpoint =
>><&tcon0_in_mixer0>;
>>> + };
>>> +
>>> + mixer0_out_tcon1: endpoint at 1
>>{
>>> + reg = <1>;
>>> + remote-endpoint =
>><&tcon1_in_mixer0>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + mixer1: mixer at 1200000 {
>>> + compatible = "allwinner,sun8i-h3-de2-mixer1";
>>> + reg = <0x01200000 0x100000>;
>>> + clocks = <&display_clocks CLK_BUS_MIXER1>,
>>> + <&display_clocks CLK_MIXER1>;
>>> + clock-names = "bus",
>>> + "mod";
>>> + resets = <&display_clocks RST_WB>;
>>> +
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + mixer1_out: port at 1 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <1>;
>>> +
>>> + mixer1_out_tcon1: endpoint at 0
>>{
>>> + reg = <0>;
>>
>>I would prefer if you could stick to the numbering scheme we're using
>>for
>>Display Engine 1.0, as in endpoint 0 links to component 0 of whatever
>>type.
>
> If we keep this we will need a ugly id property in mixer node,
> otherwise we cannot know which TCON to be bind.
Why? You can simply change the logic in your driver from:
if (remote_endpoint.id) { continue; }
to:
if (local_endpoint.id != remote_endpoint.id) { continue; }
I don't see the need for any ID property in the mixer node in this case.
The ID is already encoded into the endpoint IDs.
ChenYu
>>
>>We're probably going to stick to that for the R40's incredibly
>>complicated
>>pipeline. I don't want to have any outliers unless absolutely
>>necessary.
>>
>>ChenYu
>>
>>> + remote-endpoint =
>><&tcon1_in_mixer1>;
>>> + };
>>> +
>>> + mixer1_out_tcon0: endpoint at 1
>>{
>>> + reg = <1>;
>>> + remote-endpoint =
>><&tcon0_in_mixer1>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + tcon0: lcd-controller at 1c0c000 {
>>> + compatible = "allwinner,sun8i-h3-tcon0";
>>> + reg = <0x01c0c000 0x1000>;
>>> + interrupts = <GIC_SPI 86
>>IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&ccu CLK_BUS_TCON0>,
>>> + <&ccu CLK_TCON0>;
>>> + clock-names = "ahb",
>>> + "tcon-ch1";
>>> + resets = <&ccu RST_BUS_TCON0>;
>>> + reset-names = "lcd";
>>> + status = "disabled";
>>> +
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + tcon0_in: port at 0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <0>;
>>> +
>>> + tcon0_in_mixer0: endpoint at 0 {
>>> + reg = <0>;
>>> + remote-endpoint =
>><&mixer0_out_tcon0>;
>>> + };
>>> +
>>> + tcon0_in_mixer1: endpoint at 1 {
>>> + reg = <1>;
>>> + remote-endpoint =
>><&mixer1_out_tcon0>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + tcon1: lcd-controller at 1c0d000 {
>>> + compatible = "allwinner,sun8i-h3-tcon1";
>>> + reg = <0x01c0d000 0x1000>;
>>> + interrupts = <GIC_SPI 87
>>IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&ccu CLK_BUS_TCON1>;
>>> + clock-names = "ahb";
>>> + resets = <&ccu RST_BUS_TCON1>;
>>> + reset-names = "lcd";
>>> + status = "disabled";
>>> +
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + tcon1_in: port at 0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <0>;
>>> +
>>> + tcon1_in_mixer1: endpoint at 0 {
>>> + reg = <0>;
>>> + remote-endpoint =
>><&mixer1_out_tcon1>;
>>> + };
>>> +
>>> + tcon1_in_mixer0: endpoint at 1 {
>>> + reg = <1>;
>>> + remote-endpoint =
>><&mixer0_out_tcon1>;
>>> + };
>>> + };
>>> +
>>> + tcon1_out: port at 1 {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> + reg = <1>;
>>> +
>>> + tcon1_out_tve0: endpoint at 1 {
>>> + reg = <1>;
>>> + remote-endpoint =
>><&tve0_in_tcon1>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + tve0: tv-encoder at 1e00000 {
>>> + compatible = "allwinner,sun8i-h3-tv-encoder";
>>> + reg = <0x01e00000 0x1000>;
>>> + clocks = <&ccu CLK_BUS_TVE>, <&ccu CLK_TVE>;
>>> + clock-names = "bus", "mod";
>>> + resets = <&ccu RST_BUS_TVE>;
>>> + status = "disabled";
>>> +
>>> + assigned-clocks = <&ccu CLK_TVE>;
>>> + assigned-clock-parents = <&ccu CLK_PLL_DE>;
>>> + assigned-clock-rates = <216000000>;
>>> +
>>> + port {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + tve0_in_tcon1: endpoint at 0 {
>>> + reg = <0>;
>>> + remote-endpoint =
>><&tcon1_out_tve0>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> timer {
>>> compatible = "arm,armv7-timer";
>>> interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
>>IRQ_TYPE_LEVEL_LOW)>,
>>> --
>>> 2.12.2
>>>
>>> --
>>> You received this message because you are subscribed to the Google
>>Groups "linux-sunxi" group.
>>> To unsubscribe from this group and stop receiving emails from it,
>>send an email to linux-sunxi+unsubscribe at googlegroups.com.
>>> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
More information about the linux-arm-kernel
mailing list