[linux-sunxi] [PATCH v6 8/9] arm64: allwinner: a64: enable AXP803 regulators for Pine64

[Icenowy Zheng]

于 2017年5月19日 GMT+08:00 下午4:27:21, Andre Przywara <andre.przywara at arm.com> 写到:
>Hi,
>
>On 18/05/17 08:16, Icenowy Zheng wrote:
>> Add support of AXP803 regulators in the Pine64 device tree, in order
>to
>> enable many future functionalities, e.g. Wi-Fi.
>> 
>> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
>> ---
>> Changes in v6:
>> - Rebased on next-20170517.
>> 
>>  .../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 109
>+++++++++++++++++++++
>>  1 file changed, 109 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
>b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
>> index 36001884ed33..40921bacb39c 100644
>> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
>> @@ -118,6 +118,115 @@
>>  	};
>>  };
>>  
>> +#include "axp803.dtsi"
>> +
>> +&reg_aldo1 {
>> +	regulator-min-microvolt = <2800000>;
>> +	regulator-max-microvolt = <2800000>;
>> +	regulator-name = "vcc-csi";
>> +};
>> +
>> +&reg_aldo2 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <1800000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-pl";
>> +};
>> +
>> +&reg_aldo3 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <2700000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-pll-avcc";
>> +};
>> +
>> +&reg_dc1sw {
>> +	regulator-name = "vcc-phy";
>> +};
>> +
>> +&reg_dcdc1 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <3300000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-3v3";
>> +};
>> +
>> +&reg_dcdc2 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <1000000>;
>> +	regulator-max-microvolt = <1300000>;
>> +	regulator-name = "vdd-cpux";
>> +};
>> +
>> +/* DCDC3 is polyphased with DCDC2 */
>> +
>> +&reg_dcdc5 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <1500000>;
>> +	regulator-max-microvolt = <1500000>;
>> +	regulator-name = "vcc-dram";
>> +};
>
>I think I mentioned this before, but the Pine64 has DDR3L DRAM, which
>is
>specified to run at 1.35V (1.36V with the 20mV granularity of the AXP).
>The reset value is even (wrongly?) configured to 1.24V.
>
>So is there any reason you set the voltage to 1.5V? Is that what the
>BSP
>does? Or did you see any problems with 1.36V?

I just set it based on the schematics.

And 1.35v cannot be accurately achieved by dcdc5 and it's a problem whether to use 1.34v or 1.36v ;-)

>
>Cheers,
>Andre.
>
>> +&reg_dcdc6 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <1100000>;
>> +	regulator-max-microvolt = <1100000>;
>> +	regulator-name = "vdd-sys";
>> +};
>> +
>> +&reg_dldo1 {
>> +	regulator-min-microvolt = <3300000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-hdmi";
>> +};
>> +
>> +&reg_dldo2 {
>> +	regulator-min-microvolt = <3300000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-mipi";
>> +};
>> +
>> +&reg_dldo3 {
>> +	regulator-min-microvolt = <3300000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "avdd-csi";
>> +};
>> +
>> +&reg_dldo4 {
>> +	regulator-min-microvolt = <3300000>;
>> +	regulator-max-microvolt = <3300000>;
>> +	regulator-name = "vcc-wifi";
>> +};
>> +
>> +&reg_eldo1 {
>> +	regulator-min-microvolt = <1800000>;
>> +	regulator-max-microvolt = <1800000>;
>> +	regulator-name = "cpvdd";
>> +};
>> +
>> +&reg_eldo3 {
>> +	regulator-min-microvolt = <1800000>;
>> +	regulator-max-microvolt = <1800000>;
>> +	regulator-name = "vdd-1v8-csi";
>> +};
>> +
>> +&reg_fldo1 {
>> +	regulator-min-microvolt = <1200000>;
>> +	regulator-max-microvolt = <1200000>;
>> +	regulator-name = "vcc-1v2-hsic";
>> +};
>> +
>> +&reg_fldo2 {
>> +	regulator-always-on;
>> +	regulator-min-microvolt = <1100000>;
>> +	regulator-max-microvolt = <1100000>;
>> +	regulator-name = "vdd-cpus";
>> +};
>> +
>> +&reg_rtc_ldo {
>> +	regulator-name = "vcc-rtc";
>> +};
>> +
>>  /* On Exp and Euler connectors */
>>  &uart0 {
>>  	pinctrl-names = "default";
>>