[PATCH v4 0/6] clk: sunxi-ng: Add support for A83T CCU
Chen-Yu Tsai
wens at csie.org
Fri May 19 00:06:06 PDT 2017
Hi everyone,
This is v4 of my A83T CCU series. This is for 4.13.
Changes since v3:
- Dropped predivider for new timing mode on mmc2 clock. Replaced with
a TODO note for new timing mode support. This is the last trace of
new timing mode code.
- Simplified PLL_CPUx clocks into multiplier clocks, just like we did
for the A80. At probe time the extra P dividers are forced to /1.
These P dividers should only be used for clock rates under 288 MHz,
and never used by the boot loader or the BSP kernel.
Changes since v2:
- Dropped patches "clk: Provide option to query hardware for clk phase"
and "clk: sunxi-ng: Add class of phase clocks supporting MMC new timing
modes".
- Dropped support for MMC new timing mode. This will be added later with
MMC support. The goal for this series is to get clk support for the A83t
in. This is long overdue.
- Explicitly include ccu_mux.h and select SUNXI_CCU_MUX
Changes since v1:
- Dropped two patches that were merged
- Added clk core flag to disable caching of clock phases
- Added support for multiple variable pre-dividers
- Merged "pll-periph-ahb1" pre-divider clock into "ahb1" clock
with multiple variable pre-dividers
- Introduced new class of phase clocks that return -ENOTSUPP
when the clock is in new timing mode
- Force mmc2 clock to new timing mode
- Added back mmc2 output and sample clocks
- Fixed bit ops for forcing audio PLL configuration
- Added requirement for "losc" clock in device tree binding
- Stripped leading 0 in device node name
- Updated subject prefixes for various patches
Patch 1 adds a compatible string for the A83T CCU to the sunxi-ccu
bindings.
Patch 2 adds support for multiple variable pre-dividers to the sunxi-ng
mux class.
Patch 3 adds the driver for the A83T CCU.
Patch 4 adds the CCU device nodes, and fixes up any existing clock
phandles in the dtsi, without using the macros.
Patch 5 sets the clock accuracy for the main oscillator.
Patch 6 is for the next -rc2, switch the clock indices from raw numbers
to macros we introduced with the driver. This will be updated if more
peripherals are introduced in the same cycle.
Let me know what you think.
Cover letter excerpt from v1:
This is yet another series that adds support for the A83T CCU.
The A83T CCU has a mix of new styled (like the A80) clocks at
old (like A3x) offsets. Some differences include:
- D1/D2 style PLL clocks
- divisible audio module clocks
- new timing mode for mmc2 module clock
Regards
ChenYu
Chen-Yu Tsai (6):
dt-bindings: clock: sunxi-ccu: Add compatible string for A83T CCU
clk: sunxi-ng: Support multiple variable pre-dividers
clk: sunxi-ng: Add driver for A83T CCU
ARM: sun8i: a83t: Add CCU device nodes
ARM: sun8i: a83t: Set clock accuracy for 24MHz oscillator
ARM: sun8i: a83t: Switch to CCU device tree binding macros
.../devicetree/bindings/clock/sunxi-ccu.txt | 2 +
arch/arm/boot/dts/sun8i-a83t.dtsi | 19 +-
drivers/clk/sunxi-ng/Kconfig | 11 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun50i-a64.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun6i-a31.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun8i-a23.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun8i-a83t.c | 922 +++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun8i-a83t.h | 64 ++
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun8i-r.c | 10 +-
drivers/clk/sunxi-ng/ccu-sun8i-v3s.c | 10 +-
drivers/clk/sunxi-ng/ccu_mux.c | 15 +-
drivers/clk/sunxi-ng/ccu_mux.h | 13 +-
include/dt-bindings/clock/sun8i-a83t-ccu.h | 140 ++++
include/dt-bindings/reset/sun8i-a83t-ccu.h | 98 +++
17 files changed, 1306 insertions(+), 49 deletions(-)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-a83t.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-a83t.h
create mode 100644 include/dt-bindings/clock/sun8i-a83t-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-a83t-ccu.h
--
2.11.0
More information about the linux-arm-kernel
mailing list