[PATCH v2] ARM: dts: imx7d-pico: Add initial support
Vanessa Maegima
vanessa.maegima at nxp.com
Wed May 17 05:35:03 PDT 2017
Add the initial support for imx7d-pico board.
Add support for eMMC, USB host, USB device, PMIC, Ethernet and audio.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima at nxp.com>
---
Change since v1:
- Remove unused usdhc3 pinctrl-names entries
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx7d-pico.dts | 357 +++++++++++++++++++++++++++++++++++++++
2 files changed, 358 insertions(+)
create mode 100644 arch/arm/boot/dts/imx7d-pico.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9c5e1d9..1d42979 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -476,6 +476,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-colibri-eval-v3.dtb \
imx7d-nitrogen7.dtb \
+ imx7d-pico.dtb \
imx7d-sbc-imx7.dtb \
imx7d-sdb.dtb \
imx7d-sdb-sht11.dtb \
diff --git a/arch/arm/boot/dts/imx7d-pico.dts b/arch/arm/boot/dts/imx7d-pico.dts
new file mode 100644
index 0000000..104494a
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-pico.dts
@@ -0,0 +1,357 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx7d.dtsi"
+
+/ {
+ model = "Technexion Pico i.MX7D Board";
+ compatible = "technexion,imx7d-pico", "fsl,imx7d";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ enable-active-low;
+ };
+
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_vref_1v8: regulator-vref-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "imx7-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,cpu {
+ sound-dai = <&sai1>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+ };
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+ assigned-clock-rates = <0>, <100000000>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ status = "okay";
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: sgtl5000 at 0a {
+ #sound-dai-cells = <0>;
+ reg = <0x0a>;
+ compatible = "fsl,sgtl5000";
+ clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_vref_1v8>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ pmic: pfuze3000 at 08 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+ /* use sw1c_reg to align with pfuze100/pfuze200 */
+ sw1c_reg: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&sai1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ assigned-clocks = <&clks IMX7D_SAI1_ROOT_SRC>,
+ <&clks IMX7D_SAI1_ROOT_CLK>;
+ assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
+ assigned-clock-rates = <0>, <24576000>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ assigned-clocks = <&clks IMX7D_UART5_ROOT_SRC>;
+ assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ fsl,tuning-step = <2>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX7D_PAD_SD2_CD_B__ENET1_MDIO 0x3
+ MX7D_PAD_SD2_WP__ENET1_MDC 0x3
+ MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x1
+ MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x1
+ MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x1
+ MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x1
+ MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x1
+ MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x1
+ MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x1
+ MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x1
+ MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x1
+ MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x1
+ MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x1
+ MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX7D_PAD_UART1_TX_DATA__I2C1_SDA 0x4000007f
+ MX7D_PAD_UART1_RX_DATA__I2C1_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA 0x4000007f
+ MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK 0x1f
+ MX7D_PAD_ENET1_CRS__SAI1_TX_SYNC 0x1f
+ MX7D_PAD_ENET1_COL__SAI1_TX_DATA0 0x30
+ MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0 0x1f
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX7D_PAD_I2C4_SDA__UART5_DCE_TX 0x79
+ MX7D_PAD_I2C4_SCL__UART5_DCE_RX 0x79
+ >;
+ };
+
+ pinctrl_usbotg1_pwr: usbotg_pwr {
+ fsl,pins = <
+ MX7D_PAD_UART3_TX_DATA__GPIO4_IO5 0x14
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX7D_PAD_SD3_CMD__SD3_CMD 0x59
+ MX7D_PAD_SD3_CLK__SD3_CLK 0x19
+ MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59
+ MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59
+ MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59
+ MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59
+ MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59
+ MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59
+ MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59
+ MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59
+ MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19
+ >;
+ };
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list