[PATCH v7 11/13] ARM: sun8i: v3s: add device nodes for DE2 display pipeline

[icenowy at aosc.io]

在 2017-05-15 17:24，Maxime Ripard 写道：
> On Mon, May 15, 2017 at 12:30:43AM +0800, Icenowy Zheng wrote:
>> +		de2_clocks: clock at 1000000 {
> 
> display_clocks would be better there, we don't have to dissociate de1
> with de2

How about de_clocks ? (See A80 DTSI)

> 
>> +			compatible = "allwinner,sun8i-v3s-de2-clk";
>> +			reg = <0x01000000 0x100000>;
>> +			clocks = <&ccu CLK_DE>,
>> +				 <&ccu CLK_BUS_DE>;
>> +			clock-names = "mod",
>> +				      "bus";
>> +			resets = <&ccu RST_BUS_DE>;
>> +			#clock-cells = <1>;
>> +			#reset-cells = <1>;
>> +		};
>> +
>> +		de2_mixer0: mixer at 1100000 {
> 
> and mixer0 here is enough too.
> 
> Is there several of them? Why not just use mixer if there's only one?

Nope, here it's tagged 0 only for consistency with other SoCs.

> 
>> +			compatible = "allwinner,sun8i-v3s-de2-mixer";
>> +			reg = <0x01100000 0x100000>;
>> +			clocks = <&de2_clocks CLK_MIXER0>,
>> +				 <&de2_clocks CLK_BUS_MIXER0>;
>> +			clock-names = "mod",
>> +				      "bus";
>> +			resets = <&de2_clocks RST_MIXER0>;
>> +			assigned-clocks = <&de2_clocks CLK_MIXER0>;
>> +			assigned-clock-rates = <150000000>;
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				mixer0_out: port at 1 {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +					reg = <1>;
>> +
>> +					mixer0_out_tcon0: endpoint at 0 {
>> +						reg = <0>;
>> +						remote-endpoint = <&tcon0_in_mixer0>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		tcon0: lcd-controller at 1c0c000 {
>> +			compatible = "allwinner,sun8i-v3s-tcon";
>> +			reg = <0x01c0c000 0x1000>;
>> +			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_TCON0>,
>> +				 <&ccu CLK_TCON0>;
>> +			clock-names = "ahb",
>> +				      "tcon-ch0";
>> +			clock-output-names = "tcon-pixel-clock";
>> +			resets = <&ccu RST_BUS_TCON0>;
>> +			reset-names = "lcd";
>> +			status = "disabled";
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				tcon0_in: port at 0 {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +					reg = <0>;
>> +
>> +					tcon0_in_mixer0: endpoint at 0 {
>> +						reg = <0>;
>> +						remote-endpoint = <&mixer0_out_tcon0>;
>> +					};
>> +				};
>> +
>> +				tcon0_out: port at 1 {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +					reg = <1>;
>> +				};
>> +			};
>> +		};
>> +
>> +
> 
> You have an extra new line here.
> 
> Maxime