[PATCH v3 00/11] Broadcom Stingray SOC Initial Support

[Olof Johansson]

Hi,



On Tue, May 16, 2017 at 4:30 AM, Anup Patel <anup.patel at broadcom.com> wrote:
> This patchset adds initial support of Broadcom Stingray SOC
> by reusing existing Broadcom iProc device drivers.
>
> Most of the patches in this patchset are DT patches except
> the Stingray clock tree support which just one patch.
>
> This patchset is based on Linux-4.12-rc1 and it is also available
> at stingray-v3 branch of https://github.com/Broadcom/arm64-linux.git
>
> Changes since v2:
>  - Remove default bootargs from chosen DT node
>  - Remove "linux" prefix from stdout DT attribute of chosen DT node
>  - Remove use of GIC_CPU_MASK_xxx() for PPIs
>
> Changes since v1:
>  - Rebased patches for Linux-4.12-rc1
>  - Removed unwanted /memreserve/ from bcm958742-base.dtsi
>  - Use ranges DT property to clear view of memory-layout
>  - Make bcm-sr.h part of clock DT bindings patch
>
> Anup Patel (3):
>   dt-bindings: bcm: Add Broadcom Stingray bindings document
>   arm64: dts: Initial DTS files for Broadcom Stingray SOC
>   arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray
>
> Oza Pawandeep (1):
>   arm64: dts: Add I2C DT nodes for Stingray SoC
>
> Pramod Kumar (3):
>   arm64: dts: Add NAND DT nodes for Stingray SOC
>   arm64: dts: Add pinctrl DT nodes for Stingray SOC
>   arm64: dts: Add GPIO DT nodes for Stingray SOC
>
> Sandeep Tripathy (3):
>   dt-bindings: clk: Extend binding doc for Stingray SOC
>   clk: bcm: Add clocks for Stingray SOC
>   arm64: dts: Add clock DT nodes for Stingray SOC
>
> Srinath Mannam (1):
>   arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC
>
>  .../devicetree/bindings/arm/bcm/brcm,stingray.txt  |  12 +
>  .../bindings/clock/brcm,iproc-clocks.txt           |  76 ++++
>  arch/arm64/boot/dts/broadcom/Makefile              |   1 +
>  arch/arm64/boot/dts/broadcom/stingray/Makefile     |   6 +
>  .../boot/dts/broadcom/stingray/bcm958742-base.dtsi | 131 ++++++
>  .../boot/dts/broadcom/stingray/bcm958742k.dts      |  78 ++++
>  .../boot/dts/broadcom/stingray/bcm958742t.dts      |  40 ++
>  .../boot/dts/broadcom/stingray/stingray-clock.dtsi | 170 ++++++++
>  .../dts/broadcom/stingray/stingray-pinctrl.dtsi    | 345 ++++++++++++++++
>  .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 460 +++++++++++++++++++++
>  drivers/clk/bcm/Kconfig                            |   8 +
>  drivers/clk/bcm/Makefile                           |   1 +
>  drivers/clk/bcm/clk-sr.c                           | 300 ++++++++++++++
>  include/dt-bindings/clock/bcm-sr.h                 | 101 +++++
>  .../dt-bindings/pinctrl/brcm,pinctrl-stingray.h    |  68 +++
>  15 files changed, 1797 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/bcm/brcm,stingray.txt
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/Makefile
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-clock.dtsi
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-pinctrl.dtsi
>  create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
>  create mode 100644 drivers/clk/bcm/clk-sr.c
>  create mode 100644 include/dt-bindings/clock/bcm-sr.h
>  create mode 100644 include/dt-bindings/pinctrl/brcm,pinctrl-stingray.h

Grouping as one patchset for review is fine, but when you submit this
for merge you need to split it up:

- Documentation/devicetree can go with the driver pieces or with the
DT changes, your choice
- DTS/DTSI changes should go through the Broadcom maintainers to arm-soc
- clk changes should go to clk maintainers.

Also, there's usually no need to split up a DT introduction and having
separate pieces for NAND/pinctrl/GPIO/etc: They can all go in the main
DT submission patch.


-Olof