[PATCH v2 17/18] arm64: dts: meson-gxm-nexbox-a1: Fix node order

[Neil Armstrong]

On 05/13/2017 04:33 PM, Andreas Färber wrote:
> Sort nodes referenced by label alphabetically.
> 
> Signed-off-by: Andreas Färber <afaerber at suse.de>
> ---
>  v1 -> v2:
>  * Rebased (new nodes added)
>  
>  .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 86 +++++++++++-----------
>  1 file changed, 43 insertions(+), 43 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> index 920fac10de93..5f626d683088 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> @@ -113,10 +113,49 @@
>  	};
>  };
>  
> -&uart_AO {
> +&cvbs_vdac_port {
> +	cvbs_vdac_out: endpoint {
> +		remote-endpoint = <&cvbs_connector_in>;
> +	};
> +};
> +
> +&ethmac {
>  	status = "okay";
> -	pinctrl-0 = <&uart_ao_a_pins>;
> +
> +	pinctrl-0 = <&eth_pins>;
>  	pinctrl-names = "default";
> +
> +	/* Select external PHY by default */
> +	phy-handle = <&external_phy>;
> +
> +	amlogic,tx-delay-ns = <2>;
> +
> +	snps,reset-gpio = <&gpio GPIOZ_14 0>;
> +	snps,reset-delays-us = <0 10000 1000000>;
> +	snps,reset-active-low;
> +
> +	/* External PHY is in RGMII */
> +	phy-mode = "rgmii";
> +};
> +
> +&external_mdio {
> +	external_phy: ethernet-phy at 0 {
> +		compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +		max-speed = <1000>;
> +	};
> +};
> +
> +&hdmi_tx {
> +	status = "okay";
> +	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&hdmi_tx_tmds_port {
> +	hdmi_tx_tmds_out: endpoint {
> +		remote-endpoint = <&hdmi_connector_in>;
> +	};
>  };
>  
>  &ir {
> @@ -163,47 +202,8 @@
>  	vqmmc-supply = <&vddio_boot>;
>  };
>  
> -&ethmac {
> -	status = "okay";
> -
> -	pinctrl-0 = <&eth_pins>;
> -	pinctrl-names = "default";
> -
> -	/* Select external PHY by default */
> -	phy-handle = <&external_phy>;
> -
> -	amlogic,tx-delay-ns = <2>;
> -
> -	snps,reset-gpio = <&gpio GPIOZ_14 0>;
> -	snps,reset-delays-us = <0 10000 1000000>;
> -	snps,reset-active-low;
> -
> -	/* External PHY is in RGMII */
> -	phy-mode = "rgmii";
> -};
> -
> -&external_mdio {
> -	external_phy: ethernet-phy at 0 {
> -		compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22";
> -		reg = <0>;
> -		max-speed = <1000>;
> -	};
> -};
> -
> -&cvbs_vdac_port {
> -	cvbs_vdac_out: endpoint {
> -		remote-endpoint = <&cvbs_connector_in>;
> -	};
> -};
> -
> -&hdmi_tx {
> +&uart_AO {
>  	status = "okay";
> -	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> +	pinctrl-0 = <&uart_ao_a_pins>;
>  	pinctrl-names = "default";
>  };
> -
> -&hdmi_tx_tmds_port {
> -	hdmi_tx_tmds_out: endpoint {
> -		remote-endpoint = <&hdmi_connector_in>;
> -	};
> -};
> 

Hi Andreas,

Like a previous attempt, I'm not OK with such rework since it will break bisect and add complexity for new patches handling.

The order is not alphabetically ordered, live with it.

Neil