[PATCH v3 1/4] ACPI: Add APEI GHES Table Generation support
Michael S. Tsirkin
mst at redhat.com
Fri May 12 16:59:01 PDT 2017
On Sun, Apr 30, 2017 at 01:35:03PM +0800, Dongjiu Geng wrote:
> This implements APEI GHES Table by passing the error cper info
> to the guest via a fw_cfg_blob. After a CPER info is added, an
> SEA/SEI exception will be injected into the guest OS.
>
> Below is the table layout, the max number of error soure is 11,
> which is classified by notification type.
>
> etc/acpi/tables etc/hardware_errors
> ================ ==========================================
> +-----------+
> +--------------+ | address | +-> +--------------+
> | HEST + | registers | | | Error Status |
> + +------------+ | +---------+ | | Data Block 1 |
> | | GHES1 | --> | |address1 | --------+ | +------------+
> | | GHES2 | --> | |address2 | ------+ | | CPER |
> | | GHES3 | --> | |address3 | ----+ | | | CPER |
> | | .... | --> | | ....... | | | | | CPER |
> | | GHES10 | --> | |address10| -+ | | | | CPER |
> +-+------------+ +-+---------+ | | | +-+------------+
> | | |
> | | +---> +--------------+
> | | | Error Status |
> | | | Data Block 2 |
> | | | +------------+
> | | | | CPER |
> | | | | CPER |
> | | +-+------------+
> | |
> | +-----> +--------------+
> | | Error Status |
> | | Data Block 3 |
> | | +------------+
> | | | CPER |
> | +-+------------+
> | ...........
> +--------> +--------------+
> | Error Status |
> | Data Block 10|
> | +------------+
> | | CPER |
> | | CPER |
> | | CPER |
> +-+------------+
>
> Signed-off-by: Dongjiu Geng <gengdongjiu at huawei.com>
> ---
> default-configs/arm-softmmu.mak | 1 +
> hw/acpi/Makefile.objs | 1 +
> hw/acpi/aml-build.c | 2 +
> hw/acpi/hest_ghes.c | 203 +++++++++++++++++++++++++++++++++++
> hw/arm/virt-acpi-build.c | 6 ++
> include/hw/acpi/acpi-defs.h | 227 ++++++++++++++++++++++++++++++++++++++++
> include/hw/acpi/aml-build.h | 1 +
> include/hw/acpi/hest_ghes.h | 43 ++++++++
> 8 files changed, 484 insertions(+)
> create mode 100644 hw/acpi/hest_ghes.c
> create mode 100644 include/hw/acpi/hest_ghes.h
>
> diff --git a/default-configs/arm-softmmu.mak b/default-configs/arm-softmmu.mak
> index 1e3bd2b..d5f1552 100644
> --- a/default-configs/arm-softmmu.mak
> +++ b/default-configs/arm-softmmu.mak
> @@ -121,3 +121,4 @@ CONFIG_ACPI=y
> CONFIG_SMBIOS=y
> CONFIG_ASPEED_SOC=y
> CONFIG_GPIO_KEY=y
> +CONFIG_ACPI_APEI_GENERATION=y
> diff --git a/hw/acpi/Makefile.objs b/hw/acpi/Makefile.objs
> index 11c35bc..776b46e 100644
> --- a/hw/acpi/Makefile.objs
> +++ b/hw/acpi/Makefile.objs
> @@ -6,6 +6,7 @@ common-obj-$(CONFIG_ACPI_MEMORY_HOTPLUG) += memory_hotplug.o
> common-obj-$(CONFIG_ACPI_CPU_HOTPLUG) += cpu.o
> common-obj-$(CONFIG_ACPI_NVDIMM) += nvdimm.o
> common-obj-$(CONFIG_ACPI_VMGENID) += vmgenid.o
> +common-obj-$(CONFIG_ACPI_APEI_GENERATION) += hest_ghes.o
> common-obj-$(call lnot,$(CONFIG_ACPI_X86)) += acpi-stub.o
>
> common-obj-y += acpi_interface.o
> diff --git a/hw/acpi/aml-build.c b/hw/acpi/aml-build.c
> index c6f2032..802b98d 100644
> --- a/hw/acpi/aml-build.c
> +++ b/hw/acpi/aml-build.c
> @@ -1560,6 +1560,7 @@ void acpi_build_tables_init(AcpiBuildTables *tables)
> tables->table_data = g_array_new(false, true /* clear */, 1);
> tables->tcpalog = g_array_new(false, true /* clear */, 1);
> tables->vmgenid = g_array_new(false, true /* clear */, 1);
> + tables->hardware_errors = g_array_new(false, true /* clear */, 1);
> tables->linker = bios_linker_loader_init();
> }
>
> @@ -1570,6 +1571,7 @@ void acpi_build_tables_cleanup(AcpiBuildTables *tables, bool mfre)
> g_array_free(tables->table_data, true);
> g_array_free(tables->tcpalog, mfre);
> g_array_free(tables->vmgenid, mfre);
> + g_array_free(tables->hardware_errors, mfre);
> }
>
> /* Build rsdt table */
> diff --git a/hw/acpi/hest_ghes.c b/hw/acpi/hest_ghes.c
> new file mode 100644
> index 0000000..91d382e
> --- /dev/null
> +++ b/hw/acpi/hest_ghes.c
> @@ -0,0 +1,203 @@
> +/*
> + * APEI GHES table Generation
> + *
> + * Copyright (C) 2017 huawei.
> + *
> + * Author: Dongjiu Geng <gengdongjiu at huawei.com>
> + *
> + * This work is licensed under the terms of the GNU GPL, version 2 or later.
> + * See the COPYING file in the top-level directory.
> + *
> + */
> +
> +#include "qemu/osdep.h"
> +#include "qmp-commands.h"
> +#include "hw/acpi/acpi.h"
> +#include "hw/acpi/aml-build.h"
> +#include "hw/acpi/hest_ghes.h"
> +#include "hw/nvram/fw_cfg.h"
> +#include "sysemu/sysemu.h"
> +
> +static int ghes_generate_cper_record(uint64_t block_error_address,
> + uint64_t error_physical_addr)
> +{
> + AcpiGenericErrorStatus block;
> + AcpiGenericErrorData *gdata;
> + struct cper_sec_mem_err *mem_err;
> + uint64_t block_data_length;
> + unsigned char *buffer;
> +
> + cpu_physical_memory_read(block_error_address, &block,
> + sizeof(AcpiGenericErrorStatus));
> +
> + block_data_length = sizeof(AcpiGenericErrorStatus) + block.data_length;
> +
> + /* If the Generic Error Status Block is NULL, update
> + * the block header
> + */
> + if (!block.block_status) {
> + block.block_status = ACPI_BERT_UNCORRECTABLE;
> + block.error_severity = CPER_SEV_FATAL;
> + }
> +
> + block.data_length += sizeof(AcpiGenericErrorData);
> + block.data_length += sizeof(struct cper_sec_mem_err);
> +
> + /* Write back the Generic Error Status Block to guest memory */
> + cpu_physical_memory_write(block_error_address, &block,
> + sizeof(AcpiGenericErrorStatus));
> +
> + /* Fill in Generic Error Data Entry */
> + buffer = g_malloc(sizeof(AcpiGenericErrorData) + sizeof(cper_sec_mem_err));
> + memset(buffer, 0, sizeof(AcpiGenericErrorData) + sizeof(cper_sec_mem_err));
> + gdata = (AcpiGenericErrorData *)buffer;
> +
> + memcpy(gdata->section_type, (void *) &CPER_SEC_PLATFORM_MEM,
> + sizeof(uuid_le));
> + gdata->error_data_length = sizeof(struct cper_sec_mem_err);
> +
> + mem_err = (struct cper_sec_mem_err *) (gdata + 1);
> +
> + /* In order to simplify simulation, hardcode the CPER section to memory
> + * section.
> + */
> + mem_err->validation_bits |= CPER_MEM_VALID_ERROR_TYPE;
> + mem_err->error_type = 3;
> +
> + mem_err->validation_bits |= CPER_MEM_VALID_PA;
> + mem_err->physical_addr = error_physical_addr;
> +
> + mem_err->validation_bits |= CPER_MEM_VALID_CARD | CPER_MEM_VALID_MODULE |
> + CPER_MEM_VALID_BANK | CPER_MEM_VALID_ROW |
> + CPER_MEM_VALID_COLUMN | CPER_MEM_VALID_BIT_POSITION;
> + mem_err->card = 1;
> + mem_err->module = 2;
> + mem_err->bank = 3;
> + mem_err->row = 1;
> + mem_err->column = 2;
> + mem_err->bit_pos = 5;
> +
> + mem_err->validation_bits |= CPER_MEM_VALID_ERROR_STATUS;
> + mem_err->error_status = 4 << 8;
> +
> + /* Write back the Generic Error Data Entry to guest memory */
> + cpu_physical_memory_write(block_error_address + block_data_length, buffer,
> + sizeof(AcpiGenericErrorData) + sizeof(cper_sec_mem_err));
> +
> + g_free(buffer);
> + return BFAPEI_OK;
> +}
> +
> +void ghes_build_acpi(GArray *table_data, GArray *hardware_error,
> + BIOSLinker *linker)
> +{
> + Aml *hest;
> + uint32_t address_registers_offset;
> + AcpiTableHeader *header;
> + AcpiGenericHardwareErrorSource *error_source;
> + int i;
> +
> + int block_reqr_size = sizeof(uint64_t) + MAX_RAW_DATA_LENGTH;
> +
> + /* New address register and Error status block table size*/
> + g_array_set_size(hardware_error, MAX_ERROR_SOURCE_COUNT_V6
> + * block_reqr_size);
> +
> + /* Put this in a HEST table */
> + hest = init_aml_allocator();
> + address_registers_offset = table_data->len
> + + sizeof(AcpiHardwareErrorSourceTable)
> + + ERROR_STATUS_ADDRESS_OFFSET
> + + GAS_ADDRESS_OFFSET;
> + /* Reserve space for HEST table size*/
> + acpi_data_push(hest->buf, sizeof(AcpiHardwareErrorSourceTable)
> + + MAX_ERROR_SOURCE_COUNT_V6
> + * sizeof(AcpiGenericHardwareErrorSource));
> +
> + g_array_append_vals(table_data, hest->buf->data, hest->buf->len);
> + /* Allocate guest memory for the Data fw_cfg blob */
> + bios_linker_loader_alloc(linker, GHES_ERRORS_FW_CFG_FILE,
> + hardware_error, 4096,
> + false /* page boundary, high memory */);
> + header = (AcpiTableHeader *)(table_data->data
> + + table_data->len - hest->buf->len);
> + *(uint32_t *)(header + 1) = MAX_ERROR_SOURCE_COUNT_V6;
> + error_source = (AcpiGenericHardwareErrorSource *)((char *)header
> + + sizeof(AcpiHardwareErrorSourceTable));
> +
> + for (i = 0; i < MAX_ERROR_SOURCE_COUNT_V6; i++) {
> + error_source->type = ACPI_HEST_TYPE_GENERIC_ERROR;
> + error_source->source_id = 0;
> + error_source->related_source_id = 0xffff;
> + error_source->flags = 0;
> + error_source->enabled = 1;
> + error_source->number_of_records = 1;
> + error_source->max_sections_per_record = 1;
> + error_source->max_raw_data_length = MAX_RAW_DATA_LENGTH;
> + error_source->error_status_address.space_id =
> + ACPI_ADR_SPACE_SYSTEM_MEMORY;
> + error_source->error_status_address.bit_width = 64;
> + error_source->error_status_address.bit_offset = 0;
> + error_source->error_status_address.access_width = 4;
> + error_source->notify.type = i;
> + error_source->notify.length = sizeof(AcpiGenericHardwareErrorSource);
> +
> + bios_linker_loader_add_pointer(linker, GHES_ERRORS_FW_CFG_FILE,
> + sizeof(uint64_t) * i, sizeof(uint64_t),
> + GHES_ERRORS_FW_CFG_FILE,
> + MAX_ERROR_SOURCE_COUNT_V6 * sizeof(uint64_t) +
> + i * MAX_RAW_DATA_LENGTH);
> + bios_linker_loader_add_pointer(linker, ACPI_BUILD_TABLE_FILE,
> + address_registers_offset
> + + i * sizeof(AcpiGenericHardwareErrorSource),
> + sizeof(uint32_t), GHES_ERRORS_FW_CFG_FILE,
> + i * sizeof(uint64_t));
> +
> + bios_linker_loader_write_pointer(linker, GHES_DATA_ADDR_FW_CFG_FILE,
> + i * sizeof(uint64_t), sizeof(uint64_t),
> + GHES_ERRORS_FW_CFG_FILE,
> + MAX_ERROR_SOURCE_COUNT_V6 * sizeof(uint64_t) +
> + i * MAX_RAW_DATA_LENGTH);
> + error_source++;
> + }
> +
> + build_header(linker, table_data,
> + (void *)header, "HEST", hest->buf->len, 1, NULL, "GHES");
> +
> + free_aml_allocator();
> +}
> +
> +static GhesErrorState ges;
> +void ghes_add_fw_cfg(FWCfgState *s, GArray *hardware_error)
> +{
> +
> + int block_reqr_size = sizeof(uint64_t) + MAX_RAW_DATA_LENGTH;
> + int size = MAX_ERROR_SOURCE_COUNT_V6 * block_reqr_size;
> +
> + /* Create a read-only fw_cfg file for GHES */
> + fw_cfg_add_file(s, GHES_ERRORS_FW_CFG_FILE, hardware_error->data,
> + size);
> + /* Create a read-write fw_cfg file for Address */
> + fw_cfg_add_file_callback(s, GHES_DATA_ADDR_FW_CFG_FILE, NULL, NULL,
> + &(ges.ghes_addr_le[0]),
> + sizeof(uint64_t) * MAX_ERROR_SOURCE_COUNT_V6,
> + false);
> +}
> +
> +void ghes_update_guest(uint32_t notify, uint64_t physical_address)
> +{
> + uint64_t block_error_addr;
> +
> + if (physical_address) {
> + ges.physical_addr = physical_address;
> + block_error_addr = ges.ghes_addr_le[notify];
> + block_error_addr = le32_to_cpu(block_error_addr);
> +
> + /* A zero value in ghes_addr means that BIOS has not yet written
> + * the address
> + */
> + if (block_error_addr) {
> + ghes_generate_cper_record(block_error_addr, physical_address);
> + }
> + }
> +}
> diff --git a/hw/arm/virt-acpi-build.c b/hw/arm/virt-acpi-build.c
> index 0835e59..e7ab5dc 100644
> --- a/hw/arm/virt-acpi-build.c
> +++ b/hw/arm/virt-acpi-build.c
> @@ -45,6 +45,8 @@
> #include "hw/arm/virt.h"
> #include "sysemu/numa.h"
> #include "kvm_arm.h"
> +#include "hw/acpi/vmgenid.h"
> +#include "hw/acpi/hest_ghes.h"
>
> #define ARM_SPI_BASE 32
> #define ACPI_POWER_BUTTON_DEVICE "PWRB"
> @@ -778,6 +780,9 @@ void virt_acpi_build(VirtMachineState *vms, AcpiBuildTables *tables)
> acpi_add_table(table_offsets, tables_blob);
> build_spcr(tables_blob, tables->linker, vms);
>
> + acpi_add_table(table_offsets, tables_blob);
> + ghes_build_acpi(tables_blob, tables->hardware_errors, tables->linker);
> +
> if (nb_numa_nodes > 0) {
> acpi_add_table(table_offsets, tables_blob);
> build_srat(tables_blob, tables->linker, vms);
> @@ -892,6 +897,7 @@ void virt_acpi_setup(VirtMachineState *vms)
>
> build_state->rsdp_mr = acpi_add_rom_blob(build_state, tables.rsdp,
> ACPI_BUILD_RSDP_FILE, 0);
> + ghes_add_fw_cfg(vms->fw_cfg, tables.hardware_errors);
>
> qemu_register_reset(virt_acpi_build_reset, build_state);
> virt_acpi_build_reset(build_state);
> diff --git a/include/hw/acpi/acpi-defs.h b/include/hw/acpi/acpi-defs.h
> index 4cc3630..27adede 100644
> --- a/include/hw/acpi/acpi-defs.h
> +++ b/include/hw/acpi/acpi-defs.h
> @@ -295,6 +295,58 @@ typedef struct AcpiMultipleApicTable AcpiMultipleApicTable;
> #define ACPI_APIC_GENERIC_TRANSLATOR 15
> #define ACPI_APIC_RESERVED 16 /* 16 and greater are reserved */
>
> +#define CPER_MEM_VALID_ERROR_STATUS 0x0001
> +#define CPER_MEM_VALID_PA 0x0002
> +#define CPER_MEM_VALID_PA_MASK 0x0004
> +#define CPER_MEM_VALID_NODE 0x0008
> +#define CPER_MEM_VALID_CARD 0x0010
> +#define CPER_MEM_VALID_MODULE 0x0020
> +#define CPER_MEM_VALID_BANK 0x0040
> +#define CPER_MEM_VALID_DEVICE 0x0080
> +#define CPER_MEM_VALID_ROW 0x0100
> +#define CPER_MEM_VALID_COLUMN 0x0200
> +#define CPER_MEM_VALID_BIT_POSITION 0x0400
> +#define CPER_MEM_VALID_REQUESTOR_ID 0x0800
> +#define CPER_MEM_VALID_RESPONDER_ID 0x1000
> +#define CPER_MEM_VALID_TARGET_ID 0x2000
> +#define CPER_MEM_VALID_ERROR_TYPE 0x4000
> +#define CPER_MEM_VALID_RANK_NUMBER 0x8000
> +#define CPER_MEM_VALID_CARD_HANDLE 0x10000
> +#define CPER_MEM_VALID_MODULE_HANDLE 0x20000
> +
> +typedef struct {
> + uint8_t b[16];
> +} uuid_le;
> +
> +#define UUID_LE(a, b, c, d0, d1, d2, d3, d4, d5, d6, d7) \
> +((uuid_le) \
> +{{ (a) & 0xff, ((a) >> 8) & 0xff, ((a) >> 16) & 0xff, ((a) >> 24) & 0xff, \
> + (b) & 0xff, ((b) >> 8) & 0xff, \
> + (c) & 0xff, ((c) >> 8) & 0xff, \
> + (d0), (d1), (d2), (d3), (d4), (d5), (d6), (d7) } })
> +
> +/* Platform Memory */
> +#define CPER_SEC_PLATFORM_MEM \
> + UUID_LE(0xA5BC1114, 0x6F64, 0x4EDE, 0xB8, 0x63, 0x3E, 0x83, \
> + 0xED, 0x7C, 0x83, 0xB1)
> +
There's no reason to define these messy one-time use macros.
They just make it hard to look things up in the spec.
You can use build_append_int_noprefix to add data of
any length in LE format.
> +/* Values for Notify Type field above */
> +
> +enum acpi_hest_notify_types {
> + ACPI_HEST_NOTIFY_POLLED = 0,
> + ACPI_HEST_NOTIFY_EXTERNAL = 1,
> + ACPI_HEST_NOTIFY_LOCAL = 2,
> + ACPI_HEST_NOTIFY_SCI = 3,
> + ACPI_HEST_NOTIFY_NMI = 4,
> + ACPI_HEST_NOTIFY_CMCI = 5, /* ACPI 5.0 */
> + ACPI_HEST_NOTIFY_MCE = 6, /* ACPI 5.0 */
> + ACPI_HEST_NOTIFY_GPIO = 7, /* ACPI 6.0 */
> + ACPI_HEST_NOTIFY_SEA = 8, /* ACPI 6.1 */
> + ACPI_HEST_NOTIFY_SEI = 9, /* ACPI 6.1 */
> + ACPI_HEST_NOTIFY_GSIV = 10, /* ACPI 6.1 */
> + ACPI_HEST_NOTIFY_RESERVED = 11 /* 11 and greater are reserved */
> +};
> +
these are never reused, it's best
> /*
> * MADT sub-structures (Follow MULTIPLE_APIC_DESCRIPTION_TABLE)
> */
> @@ -475,6 +527,181 @@ struct AcpiSystemResourceAffinityTable
> } QEMU_PACKED;
> typedef struct AcpiSystemResourceAffinityTable AcpiSystemResourceAffinityTable;
>
> +#define ACPI_ADR_SPACE_SYSTEM_MEMORY (uint8_t) 0
> +#define ACPI_ADR_SPACE_SYSTEM_IO (uint8_t) 1
> +#define ACPI_ADR_SPACE_PCI_CONFIG (uint8_t) 2
> +#define ACPI_ADR_SPACE_EC (uint8_t) 3
> +#define ACPI_ADR_SPACE_SMBUS (uint8_t) 4
> +#define ACPI_ADR_SPACE_CMOS (uint8_t) 5
> +#define ACPI_ADR_SPACE_PCI_BAR_TARGET (uint8_t) 6
> +#define ACPI_ADR_SPACE_IPMI (uint8_t) 7
> +#define ACPI_ADR_SPACE_GPIO (uint8_t) 8
> +#define ACPI_ADR_SPACE_GSBUS (uint8_t) 9
> +#define ACPI_ADR_SPACE_PLATFORM_COMM (uint8_t) 10
> +
We already have macros for some of these and APIs to
format it.
> +/* GAS - Generic Address Structure */
> +struct acpi_generic_address {
> + uint8_t space_id; /* Address space where
> + *struct or register exists
> + */
> + uint8_t bit_width; /* Size in bits of given register */
> + uint8_t bit_offset; /* Bit offset within the register */
> + uint8_t access_width; /* Minimum Access size (ACPI 3.0) */
> + uint64_t address; /* 64-bit address of struct or register */
> +} __attribute__ ((packed));
> +
> +/* Hardware Error Notification */
> +struct acpi_hest_notify {
> + uint8_t type;
> + uint8_t length;
> + uint16_t config_write_enable;
> + uint32_t poll_interval;
> + uint32_t vector;
> + uint32_t polling_threshold_value;
> + uint32_t polling_threshold_window;
> + uint32_t error_threshold_value;
> + uint32_t error_threshold_window;
> +};
> +
> +enum acpi_hest_types {
> + ACPI_HEST_TYPE_IA32_CHECK = 0,
> + ACPI_HEST_TYPE_IA32_CORRECTED_CHECK = 1,
> + ACPI_HEST_TYPE_IA32_NMI = 2,
> + ACPI_HEST_TYPE_NOT_USED3 = 3,
> + ACPI_HEST_TYPE_NOT_USED4 = 4,
> + ACPI_HEST_TYPE_NOT_USED5 = 5,
> + ACPI_HEST_TYPE_AER_ROOT_PORT = 6,
> + ACPI_HEST_TYPE_AER_ENDPOINT = 7,
> + ACPI_HEST_TYPE_AER_BRIDGE = 8,
> + ACPI_HEST_TYPE_GENERIC_ERROR = 9,
> + ACPI_HEST_TYPE_GENERIC_ERROR_V2 = 10,
> + ACPI_HEST_TYPE_RESERVED = 11 /* 11 and greater are reserved */
> +};
> +
> +/* Values for block_status flags above */
> +#define ACPI_BERT_UNCORRECTABLE (1)
> +#define ACPI_BERT_CORRECTABLE (1 << 1)
> +#define ACPI_BERT_MULTIPLE_UNCORRECTABLE (1 << 2)
> +#define ACPI_BERT_MULTIPLE_CORRECTABLE (1 << 3)
> +/* 8 bits, error count */
> +#define ACPI_BERT_ERROR_ENTRY_COUNT (0xFF << 4)
> +
> +/* Generic Hardware Error Source Structure */
> +struct AcpiGenericHardwareErrorSource {
> + uint16_t type;
> + uint16_t source_id;
> + uint16_t related_source_id;
> + uint8_t flags;
> + uint8_t enabled;
> + uint32_t number_of_records;
> + uint32_t max_sections_per_record;
> + uint32_t max_raw_data_length;
> + struct acpi_generic_address error_status_address;
> + struct acpi_hest_notify notify;
> + uint32_t error_status_block_length;
> +} QEMU_PACKED;
> +typedef struct AcpiGenericHardwareErrorSource AcpiGenericHardwareErrorSource;
> +
> +/* Generic Hardware Error Source , version 2 */
> +struct AcpiGenericHardwareErrorSourceV2 {
> + uint16_t type;
> + uint16_t source_id;
> + uint16_t related_source_id;
> + uint8_t flags;
> + uint8_t enabled;
> + uint32_t number_of_records;
> + uint32_t max_sections_per_record;
> + uint32_t max_raw_data_length;
> + struct acpi_generic_address error_status_address;
> + struct acpi_hest_notify notify;
> + uint32_t error_status_block_length;
> + struct acpi_generic_address read_ack_register;
> + uint64_t read_ack_preserve;
> + uint64_t read_ack_write;
> +} QEMU_PACKED;
> +typedef struct AcpiGenericHardwareErrorSourceV2
> + AcpiGenericHardwareErrorSourceV2;
> +
> +/* Generic Error Status block */
> +
> +struct AcpiGenericErrorStatus {
> + uint32_t block_status;
> + uint32_t raw_data_offset;
> + uint32_t raw_data_length;
> + uint32_t data_length;
> + uint32_t error_severity;
> +};
> +typedef struct AcpiGenericErrorStatus AcpiGenericErrorStatus;
> +
> +/* Generic Error Data entry */
> +
> +struct AcpiGenericErrorData {
> + uint8_t section_type[16];
> + uint32_t error_severity;
> + uint16_t revision;
> + uint8_t validation_bits;
> + uint8_t flags;
> + uint32_t error_data_length;
> + uint8_t fru_id[16];
> + uint8_t fru_text[20];
> +};
> +typedef struct AcpiGenericErrorData AcpiGenericErrorData;
> +
> +/* Extension for revision 0x0300 */
> +struct AcpiGenericErrorDataV300 {
> + uint8_t section_type[16];
> + uint32_t error_severity;
> + uint16_t revision;
> + uint8_t validation_bits;
> + uint8_t flags;
> + uint32_t error_data_length;
> + uint8_t fru_id[16];
> + uint8_t fru_text[20];
> + uint64_t time_stamp;
> +};
> +typedef struct AcpiGenericErrorDataV300 AcpiGenericErrorDataV300;
> +
> +enum {
> + CPER_SEV_RECOVERABLE,
> + CPER_SEV_FATAL,
> + CPER_SEV_CORRECTED,
> + CPER_SEV_INFORMATIONAL,
> +};
> +
> +/* Memory Error Section */
> +struct cper_sec_mem_err {
> + uint64_t validation_bits;
> + uint64_t error_status;
> + uint64_t physical_addr;
> + uint64_t physical_addr_mask;
> + uint16_t node;
> + uint16_t card;
> + uint16_t module;
> + uint16_t bank;
> + uint16_t device;
> + uint16_t row;
> + uint16_t column;
> + uint16_t bit_pos;
> + uint64_t requestor_id;
> + uint64_t responder_id;
> + uint64_t target_id;
> + uint8_t error_type;
> + uint8_t reserved;
> + uint16_t rank;
> + uint16_t mem_array_handle; /* card handle in UEFI 2.4 */
> + uint16_t mem_dev_handle; /* module handle in UEFI 2.4 */
> +};
> + typedef struct cper_sec_mem_err cper_sec_mem_err;
> +
> +/*
> + * HEST Description Table
> + */
> +struct AcpiHardwareErrorSourceTable {
> + ACPI_TABLE_HEADER_DEF /* ACPI common table header */
> + uint32_t error_source_count;
> +} QEMU_PACKED;
> +typedef struct AcpiHardwareErrorSourceTable AcpiHardwareErrorSourceTable;
> +
> #define ACPI_SRAT_PROCESSOR_APIC 0
> #define ACPI_SRAT_MEMORY 1
> #define ACPI_SRAT_PROCESSOR_x2APIC 2
> diff --git a/include/hw/acpi/aml-build.h b/include/hw/acpi/aml-build.h
> index 00c21f1..c1d15b3 100644
> --- a/include/hw/acpi/aml-build.h
> +++ b/include/hw/acpi/aml-build.h
> @@ -211,6 +211,7 @@ struct AcpiBuildTables {
> GArray *rsdp;
> GArray *tcpalog;
> GArray *vmgenid;
> + GArray *hardware_errors;
> BIOSLinker *linker;
> } AcpiBuildTables;
>
> diff --git a/include/hw/acpi/hest_ghes.h b/include/hw/acpi/hest_ghes.h
> new file mode 100644
> index 0000000..0cadc2b
> --- /dev/null
> +++ b/include/hw/acpi/hest_ghes.h
> @@ -0,0 +1,43 @@
> +#ifndef ACPI_GHES_H
> +#define ACPI_GHES_H
> +
> +#include "hw/acpi/bios-linker-loader.h"
> +
> +#define GHES_ERRORS_FW_CFG_FILE "etc/hardware_errors"
> +#define GHES_DATA_ADDR_FW_CFG_FILE "etc/hardware_errors_addr"
> +
> +#define GAS_ADDRESS_OFFSET 4
> +#define ERROR_STATUS_ADDRESS_OFFSET 20
> +#define NOTIFICATION_STRUCTURE 32
> +
> +#define BFAPEI_OK 0
> +#define BFAPEI_FAIL 1
> +
> +/* The max number of error source, the error sources
> + * are classified by notification type, below is the definition
> + * 0 - Polled
> + * 1 - External Interrupt
> + * 2 - Local Interrupt
> + * 3 - SCI
> + * 4 - NMI
> + * 5 - CMCI
> + * 6 - MCE
> + * 7 - GPIO-Signal
> + * 8 - ARMv8 SEA
> + * 9 - ARMv8 SEI
> + * 10 - External Interrupt - GSIV
> + */
> +#define MAX_ERROR_SOURCE_COUNT_V6 11
> +/* The max size in Bytes for one error block */
> +#define MAX_RAW_DATA_LENGTH 0x1000
> +
> +typedef struct GhesErrorState {
> + uint64_t physical_addr;
> + uint64_t ghes_addr_le[8];
> +} GhesErrorState;
> +
> +void ghes_build_acpi(GArray *table_data, GArray *hardware_error,
> + BIOSLinker *linker);
> +void ghes_add_fw_cfg(FWCfgState *s, GArray *guid);
> +void ghes_update_guest(uint32_t notify, uint64_t physical_address);
> +#endif
> --
> 1.8.3.1
More information about the linux-arm-kernel
mailing list