[PATCH v3 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM
Vivek Gautam
vivek.gautam at codeaurora.org
Mon May 8 21:47:22 PDT 2017
Hi,
On 05/08/2017 05:51 PM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Thursday 04 May 2017 11:38 PM, Martin Blumenstingl wrote:
>> Hi Kishon,
>>
>> On Mon, Apr 17, 2017 at 9:11 PM, Martin Blumenstingl
>> <martin.blumenstingl at googlemail.com> wrote:
>>> This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
>>> (both SoCs are using the same USB PHY register layout).
>>>
>>> The USB2 PHY is a simple PHY which only has a few registers to configure
>>> the mode (host/device) and a reset register (to enable/disable the PHY).
>>>
>>> Unfortunately there are no datasheets available for this PHY. The driver
>>> was written by reading the code from Amlogic's GPL kernel sources and
>>> by analyzing the registers on an actual GXL and GXM device running the
>>> kernel that was shipped on the boards I have.
>>>
>>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>>> ---
>>> drivers/phy/Kconfig | 12 ++
>>> drivers/phy/Makefile | 1 +
>>> drivers/phy/phy-meson-gxl-usb2.c | 261 +++++++++++++++++++++++++++++++++++++++
>>> 3 files changed, 274 insertions(+)
>>> create mode 100644 drivers/phy/phy-meson-gxl-usb2.c
>>>
>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>> index 005cadb7a3f8..fada8354c0fe 100644
>>> --- a/drivers/phy/Kconfig
>>> +++ b/drivers/phy/Kconfig
>>> @@ -511,4 +511,16 @@ config PHY_MESON8B_USB2
>>> and GXBB SoCs.
>>> If unsure, say N.
>>>
>>> +config PHY_MESON_GXL_USB
>>> + tristate "Meson GXL and GXM USB2 PHY drivers"
>>> + default ARCH_MESON
>>> + depends on OF && (ARCH_MESON || COMPILE_TEST)
>>> + depends on USB_SUPPORT
>>> + select GENERIC_PHY
>>> + select REGMAP_MMIO
>>> + help
>>> + Enable this to support the Meson USB2 PHYs found in Meson
>>> + GXL and GXM SoCs.
>>> + If unsure, say N.
>>> +
>>> endmenu
>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>>> index dd8f3b5d2918..4f5ede46b0b9 100644
>>> --- a/drivers/phy/Makefile
>>> +++ b/drivers/phy/Makefile
>>> @@ -62,3 +62,4 @@ obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
>>> obj-$(CONFIG_ARCH_TEGRA) += tegra/
>>> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
>>> obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
>>> +obj-$(CONFIG_PHY_MESON_GXL_USB) += phy-meson-gxl-usb2.o
>>> diff --git a/drivers/phy/phy-meson-gxl-usb2.c b/drivers/phy/phy-meson-gxl-usb2.c
>>> new file mode 100644
>>> index 000000000000..f5fbd3c09542
>>> --- /dev/null
>>> +++ b/drivers/phy/phy-meson-gxl-usb2.c
>>> @@ -0,0 +1,261 @@
>>> +/*
>>> + * Meson GXL and GXM USB2 PHY driver
>>> + *
>>> + * Copyright (C) 2017 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License version 2 as
>>> + * published by the Free Software Foundation.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
>>> + */
>>> +
>>> +#include <linux/delay.h>
>>> +#include <linux/io.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/phy/phy.h>
>>> +#include <linux/platform_device.h>
>>> +
>>> +/* bits [31:27] are read-only */
>>> +#define U2P_R0 0x0
>>> + #define U2P_R0_BYPASS_SEL BIT(0)
>>> + #define U2P_R0_BYPASS_DM_EN BIT(1)
>>> + #define U2P_R0_BYPASS_DP_EN BIT(2)
>>> + #define U2P_R0_TXBITSTUFF_ENH BIT(3)
>>> + #define U2P_R0_TXBITSTUFF_EN BIT(4)
>>> + #define U2P_R0_DM_PULLDOWN BIT(5)
>>> + #define U2P_R0_DP_PULLDOWN BIT(6)
>>> + #define U2P_R0_DP_VBUS_VLD_EXT_SEL BIT(7)
>>> + #define U2P_R0_DP_VBUS_VLD_EXT BIT(8)
>>> + #define U2P_R0_ADP_PRB_EN BIT(9)
>>> + #define U2P_R0_ADP_DISCHARGE BIT(10)
>>> + #define U2P_R0_ADP_CHARGE BIT(11)
>>> + #define U2P_R0_DRV_VBUS BIT(12)
>>> + #define U2P_R0_ID_PULLUP BIT(13)
>>> + #define U2P_R0_LOOPBACK_EN_B BIT(14)
>>> + #define U2P_R0_OTG_DISABLE BIT(15)
>>> + #define U2P_R0_COMMON_ONN BIT(16)
>>> + #define U2P_R0_FSEL_MASK GENMASK(19, 17)
>>> + #define U2P_R0_REF_CLK_SEL_MASK GENMASK(21, 20)
>>> + #define U2P_R0_POWER_ON_RESET BIT(22)
>>> + #define U2P_R0_V_ATE_TEST_EN_B_MASK GENMASK(24, 23)
>>> + #define U2P_R0_ID_SET_ID_DQ BIT(25)
>>> + #define U2P_R0_ATE_RESET BIT(26)
>>> + #define U2P_R0_FSV_MINUS BIT(27)
>>> + #define U2P_R0_FSV_PLUS BIT(28)
>>> + #define U2P_R0_BYPASS_DM_DATA BIT(29)
>>> + #define U2P_R0_BYPASS_DP_DATA BIT(30)
>>> +
>>> +#define U2P_R1 0x4
>>> + #define U2P_R1_BURN_IN_TEST BIT(0)
>>> + #define U2P_R1_ACA_ENABLE BIT(1)
>>> + #define U2P_R1_DCD_ENABLE BIT(2)
>>> + #define U2P_R1_VDAT_SRC_EN_B BIT(3)
>>> + #define U2P_R1_VDAT_DET_EN_B BIT(4)
>>> + #define U2P_R1_CHARGES_SEL BIT(5)
>>> + #define U2P_R1_TX_PREEMP_PULSE_TUNE BIT(6)
>>> + #define U2P_R1_TX_PREEMP_AMP_TUNE_MASK GENMASK(8, 7)
>>> + #define U2P_R1_TX_RES_TUNE_MASK GENMASK(10, 9)
>>> + #define U2P_R1_TX_RISE_TUNE_MASK GENMASK(12, 11)
>>> + #define U2P_R1_TX_VREF_TUNE_MASK GENMASK(16, 13)
>>> + #define U2P_R1_TX_FSLS_TUNE_MASK GENMASK(20, 17)
>>> + #define U2P_R1_TX_HSXV_TUNE_MASK GENMASK(22, 21)
>>> + #define U2P_R1_OTG_TUNE_MASK GENMASK(25, 23)
>>> + #define U2P_R1_SQRX_TUNE_MASK GENMASK(28, 26)
>>> + #define U2P_R1_COMP_DIS_TUNE_MASK GENMASK(31, 29)
>>> +
>>> +/* bits [31:14] are read-only */
>>> +#define U2P_R2 0x8
>>> + #define U2P_R2_DATA_IN_MASK GENMASK(3, 0)
>>> + #define U2P_R2_DATA_IN_EN_MASK GENMASK(7, 4)
>>> + #define U2P_R2_ADDR_MASK GENMASK(11, 8)
>>> + #define U2P_R2_DATA_OUT_SEL BIT(12)
>>> + #define U2P_R2_CLK BIT(13)
>>> + #define U2P_R2_DATA_OUT_MASK GENMASK(17, 14)
>>> + #define U2P_R2_ACA_PIN_RANGE_C BIT(18)
>>> + #define U2P_R2_ACA_PIN_RANGE_B BIT(19)
>>> + #define U2P_R2_ACA_PIN_RANGE_A BIT(20)
>>> + #define U2P_R2_ACA_PIN_GND BIT(21)
>>> + #define U2P_R2_ACA_PIN_FLOAT BIT(22)
>>> + #define U2P_R2_CHARGE_DETECT BIT(23)
>>> + #define U2P_R2_DEVICE_SESSION_VALID BIT(24)
>>> + #define U2P_R2_ADP_PROBE BIT(25)
>>> + #define U2P_R2_ADP_SENSE BIT(26)
>>> + #define U2P_R2_SESSION_END BIT(27)
>>> + #define U2P_R2_VBUS_VALID BIT(28)
>>> + #define U2P_R2_B_VALID BIT(29)
>>> + #define U2P_R2_A_VALID BIT(30)
>>> + #define U2P_R2_ID_DIG BIT(31)
>>> +
>>> +#define U2P_R3 0xc
>>> +
>>> +#define RESET_COMPLETE_TIME 500
>>> +
>>> +struct phy_meson_gxl_usb2_priv {
>>> + struct regmap *regmap;
>>> + enum phy_mode mode;
>>> + int is_enabled;
>>> +};
>>> +
>>> +static const struct regmap_config phy_meson_gxl_usb2_regmap_conf = {
>>> + .reg_bits = 8,
>>> + .val_bits = 32,
>>> + .reg_stride = 4,
>>> + .max_register = U2P_R3,
>>> +};
>>> +
>>> +static int phy_meson_gxl_usb2_reset(struct phy *phy)
>>> +{
>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>> +
>>> + if (!priv->is_enabled)
>>> + return 0;
>>> +
>>> + /* reset the PHY and wait until settings are stabilized */
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
>>> + U2P_R0_POWER_ON_RESET);
>>> + udelay(RESET_COMPLETE_TIME);
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET, 0);
>>> + udelay(RESET_COMPLETE_TIME);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int phy_meson_gxl_usb2_set_mode(struct phy *phy, enum phy_mode mode)
>>> +{
>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>> +
>>> + switch (mode) {
>>> + case PHY_MODE_USB_HOST:
>>> + case PHY_MODE_USB_OTG:
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
>>> + U2P_R0_DM_PULLDOWN);
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
>>> + U2P_R0_DP_PULLDOWN);
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP, 0);
>>> + break;
>>> +
>>> + case PHY_MODE_USB_DEVICE:
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
>>> + 0);
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
>>> + 0);
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP,
>>> + U2P_R0_ID_PULLUP);
>>> + break;
>>> +
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + phy_meson_gxl_usb2_reset(phy);
>>> +
>>> + priv->mode = mode;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int phy_meson_gxl_usb2_power_off(struct phy *phy)
>>> +{
>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>> +
>>> + priv->is_enabled = 0;
>>> +
>>> + /* power off the PHY by putting it into reset mode */
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
>>> + U2P_R0_POWER_ON_RESET);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int phy_meson_gxl_usb2_power_on(struct phy *phy)
>>> +{
>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>> + int ret;
>>> +
>>> + priv->is_enabled = 1;
>>> +
>>> + /* power on the PHY by taking it out of reset mode */
>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET, 0);
>>> +
>>> + ret = phy_meson_gxl_usb2_set_mode(phy, priv->mode);
>>> + if (ret) {
>>> + phy_meson_gxl_usb2_power_off(phy);
>>> +
>>> + dev_err(&phy->dev, "Failed to initialize PHY with mode %d\n",
>>> + priv->mode);
>>> + return ret;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct phy_ops phy_meson_gxl_usb2_ops = {
>>> + .power_on = phy_meson_gxl_usb2_power_on,
>>> + .power_off = phy_meson_gxl_usb2_power_off,
>>> + .set_mode = phy_meson_gxl_usb2_set_mode,
>>> + .reset = phy_meson_gxl_usb2_reset,
>>> + .owner = THIS_MODULE,
>>> +};
>>> +
>>> +static int phy_meson_gxl_usb2_probe(struct platform_device *pdev)
>>> +{
>>> + struct device *dev = &pdev->dev;
>>> + struct phy_provider *phy_provider;
>>> + struct resource *res;
>>> + struct phy_meson_gxl_usb2_priv *priv;
>>> + struct phy *phy;
>>> + void __iomem *base;
>>> +
>>> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>>> + if (!priv)
>>> + return -ENOMEM;
>>> +
>>> + platform_set_drvdata(pdev, priv);
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + base = devm_ioremap_resource(dev, res);
>>> + if (IS_ERR(base))
>>> + return PTR_ERR(base);
>>> +
>>> + priv->mode = PHY_MODE_USB_HOST;
>>> +
>>> + priv->regmap = devm_regmap_init_mmio(dev, base,
>>> + &phy_meson_gxl_usb2_regmap_conf);
>>> + if (IS_ERR(priv->regmap))
>>> + return PTR_ERR(priv->regmap);
>>> +
>>> + phy = devm_phy_create(dev, NULL, &phy_meson_gxl_usb2_ops);
>>> + if (IS_ERR(phy)) {
>>> + dev_err(dev, "failed to create PHY\n");
>>> + return PTR_ERR(phy);
>>> + }
>>> +
>>> + phy_set_drvdata(phy, priv);
>>> +
>>> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>>> +
>>> + return PTR_ERR_OR_ZERO(phy_provider);
>>> +}
>>> +
>>> +static const struct of_device_id phy_meson_gxl_usb2_of_match[] = {
>>> + { .compatible = "amlogic,meson-gxl-usb2-phy", },
>>> + { },
>>> +};
>>> +MODULE_DEVICE_TABLE(of, phy_meson_gxl_usb2_of_match);
>>> +
>>> +static struct platform_driver phy_meson_gxl_usb2_driver = {
>>> + .probe = phy_meson_gxl_usb2_probe,
>>> + .driver = {
>>> + .name = "phy-meson-gxl-usb2",
>>> + .of_match_table = phy_meson_gxl_usb2_of_match,
>>> + },
>>> +};
>>> +module_platform_driver(phy_meson_gxl_usb2_driver);
>>> +
>>> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl at googlemail.com>");
>>> +MODULE_DESCRIPTION("Meson GXL and GXM USB2 PHY driver");
>>> +MODULE_LICENSE("GPL v2");
>>> --
>>> 2.12.2
>>>
>> the devicetree documentation already got Rob's ACK. is there anything
>> that I still need to fix? I would really like to see this getting into
>> 4.13
> I don't have any further comments. I'll queue this once -rc1 is tagged. Btw
> Vivek Gautam has plans to change the directory structure of phy, so you might
> have to resend this patch once his patch is merged.
>
> Vivek, since phy tree is already merged to Linus, can you send your
> restructuring patch asap based on linus latest?
Sure, I will send the patch soon this week.
Regards
Vivek
>
> Thanks
> Kishon
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
More information about the linux-arm-kernel
mailing list