[PATCH 0/4] TI Bluetooth serdev support

[Adam Ford]

On Sun, Apr 30, 2017 at 11:04 AM, Sebastian Reichel <sre at kernel.org> wrote:
> Hi,
>
> On Sun, Apr 30, 2017 at 10:14:20AM -0500, Adam Ford wrote:
>> On Wed, Apr 5, 2017 at 1:30 PM, Rob Herring <robh at kernel.org> wrote:
>> > This series adds serdev support to the HCI LL protocol used on TI BT
>> > modules and enables support on HiKey board with with the WL1835 module.
>> > With this the custom TI UIM daemon and btattach are no longer needed.
>>
>> Without UIM daemon, what instruction do you use to load the BT firmware?
>>
>> I was thinking 'hciattach' but I was having trouble.  I was hoping you
>> might have some insight.
>>
>>  hciattach -t 30 -s 115200 /dev/ttymxc1 texas 3000000 flow  Just
>> returns a timeout.
>>
>> I modified my i.MX6 device tree per the binding documentation and
>> setup the regulators and enable GPIO pins.
>
> If you configured everything correctly no userspace interaction is
> required. The driver should request the firmware automatically once
> you power up the bluetooth device.
>
> Apart from DT changes make sure, that the following options are
> enabled and check dmesg for any hints.
>
> CONFIG_SERIAL_DEV_BUS
> CONFIG_SERIAL_DEV_CTRL_TTYPORT
> CONFIG_BT_HCIUART
> CONFIG_BT_HCIUART_LL
>


I have enabled those flags, and I have updated my device tree.
I am testing this on an OMAP3630 (DM3730) board with a WL1283.  I am
getting a lot of timeout errors.  I tested this against the original
implemention I had in pdata-quirks.c using the ti-st driver, uim & and
the btwilink driver.

I pulled in some of the newer patches to enable the wl1283-st, but I
am obviously missing something.

I   58.717651] Bluetooth: hci0: Reading TI version information failed
(-110)
[   58.724853] Bluetooth: hci0: download firmware failed, retrying...
[   60.957641] Bluetooth: hci0 command 0x1001 tx timeout
[   68.957641] Bluetooth: hci0: Reading TI version information failed
(-110)
[   68.964843] Bluetooth: hci0: download firmware failed, retrying...
[   69.132171] Bluetooth: Unknown HCI packet type 06
[   69.138244] Bluetooth: Unknown HCI packet type 0c
[   69.143249] Bluetooth: Unknown HCI packet type 40
[   69.148498] Bluetooth: Unknown HCI packet type 20
[   69.153533] Bluetooth: Data length is too large
[   69.158569] Bluetooth: Unknown HCI packet type a0
[   69.163574] Bluetooth: Unknown HCI packet type 00
[   69.168731] Bluetooth: Unknown HCI packet type 00
[   69.173736] Bluetooth: Unknown HCI packet type 34
[   69.178924] Bluetooth: Unknown HCI packet type 91
[   71.197631] Bluetooth: hci0 command 0x1001 tx timeout
[   79.197662] Bluetooth: hci0: Reading TI version information failed (-110)

Since the pdata-quirks and original ti-st drivers work together, I
know the hardware is fine.  The only change to the device tree is the
addition of the Bluetooth container:

bluetooth {
  compatible = "ti,wl1283-st";
  enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
};

Any thoughts or suggestions to try?  I get similar behavior on an
i.MX6 board with a wl1837-st module as well.

adam
> -- Sebastian