[PATCH] arm64: dts: rk3399: add support for firefly-rk3399 board
Heiko Stuebner
heiko at sntech.de
Fri Mar 31 05:56:18 PDT 2017
Hi Kever,
Am Freitag, 31. März 2017, 17:59:07 CEST schrieb Kever Yang:
> Firefly-rk3399 is a bord from T-Firefly, you can find detail about
> it here:
> http://en.t-firefly.com/en/firenow/Firefly_RK3399/
>
> This patch add basic node for the board and make it able to bring
> up.
This more a first glance, I didn't check every binding, but already found
some dubious ones, so in general, please make sure to only include nodes
with approved bindings.
[...]
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> arch/arm64/boot/dts/rockchip/rk3399-firefly.dts | 772 ++++++++++++++++++++++++
please provide a binding addition for the board in a separate patch as well.
> 2 files changed, 773 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 3a86289..dd3d550 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
if possible, please rebase on top of my for-next branch, as we also
have the first gru board in there now.
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
> new file mode 100644
> index 0000000..686977b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
> @@ -0,0 +1,772 @@
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/pwm/pwm.h>
> +#include "rk3399.dtsi"
> +
> +/ {
> + model = "Rockchip RK3399 Firefly Board (Linux Opensource)";
> + compatible = "rockchip,rk3399-firefly-linux", "rockchip,rk3399";
Just to make sure, is this really a Rockchip board? I would've expected
to see something like "firefly,firefly-rk3399" here, like on the rk3288-
variant. Not a requirement, just a question to clarify who designed the
board please :-) .
> +
> + backlight: backlight {
> + status = "okay";
> + compatible = "pwm-backlight";
> + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> + pwms = <&pwm0 0 25000 0>;
> + brightness-levels = <
> + 0 1 2 3 4 5 6 7
> + 8 9 10 11 12 13 14 15
> + 16 17 18 19 20 21 22 23
> + 24 25 26 27 28 29 30 31
> + 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
> + default-brightness-level = <200>;
> + };
> +
> + clkin_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "clkin_gmac";
> + #clock-cells = <0>;
> + };
> +
> + rt5640-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rockchip,rt5640-codec";
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphone Jack";
> + simple-audio-card,routing =
> + "Mic Jack", "MICBIAS1",
> + "IN1P", "Mic Jack",
> + "Headphone Jack", "HPOL",
> + "Headphone Jack", "HPOR";
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&rt5640>;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk808 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> +
> + /*
> + * On the module itself this is one of these (depending
> + * on the actual card populated):
> + * - SDIO_RESET_L_WL_REG_ON
> + * - PDN (power down when low)
> + */
> + reset-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; /* GPIO0_B2 */
Thanks to Andy's persistence, we have nice constants in the pinctrl-
binding-header now, like RK_PB2 for the above. So you can drop the
comment and use the constant instead for easier reading.
Same for other pins.
> + };
> +
> + vcc3v3_pcie: vcc3v3-pcie-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_drv>;
> + regulator-name = "vcc3v3_pcie";
> + };
> +
> + vcc3v3_sys: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc5v0_host: vcc5v0-host-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc5v0_host";
> + regulator-always-on;
> + };
> +
> + vcc5v0_sys: vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vcc_phy: vcc-phy-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_phy";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm2 0 25000 1>;
> + regulator-name = "vdd_log";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + /* for rockchip boot on */
> + rockchip,pwm_id= <2>;
> + rockchip,pwm_voltage = <1000000>;
> + };
> +
> + vccadc_ref: vccadc-ref {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc1v8_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + wireless-wlan {
> + compatible = "wlan-platdata";
> + rockchip,grf = <&grf>;
> + wifi_chip_type = "ap6354";
> + sdio_vref = <1800>;
> + WIFI,host_wake_irq = <&gpio0 3 GPIO_ACTIVE_HIGH>; /* GPIO0_a3 */
> + status = "okay";
that is not a valid binding, am I right? ;-)
So should be dropped.
> + };
> +
> + wireless-bluetooth {
> + compatible = "bluetooth-platdata";
> + //wifi-bt-power-toggle;
> + uart_rts_gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; /* GPIO2_C3 */
> + pinctrl-names = "default", "rts_gpio";
> + pinctrl-0 = <&uart0_rts>;
> + pinctrl-1 = <&uart0_gpios>;
> + //BT,power_gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>; /* GPIOx_xx */
> + BT,reset_gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>; /* GPIO0_B1 */
> + BT,wake_gpio = <&gpio2 26 GPIO_ACTIVE_HIGH>; /* GPIO2_D2 */
> + BT,wake_host_irq = <&gpio0 4 GPIO_ACTIVE_HIGH>; /* GPIO0_A4 */
> + status = "okay";
> + };
same here
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_RMII_SRC>;
> + assigned-clock-parents = <&clkin_gmac>;
> + clock_in_out = "input";
> + phy-supply = <&vcc_phy>;
> + phy-mode = "rgmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 50000>;
> + tx_delay = <0x28>;
> + rx_delay = <0x11>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
> + clock-frequency = <400000>;
> +
> + vdd_cpu_b: syr827 at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + vin-supply = <&vcc5v0_sys>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_cpu_b";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + vsel-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
> + fcs,suspend-voltage-selector = <0>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-state = <3>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: syr828 at 41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + vin-supply = <&vcc5v0_sys>;
> + regulator-compatible = "fan53555-reg";
> + regulator-name = "vdd_gpu";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-state = <3>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk808: pmic at 1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc3v3_sys>;
> + vcc2-supply = <&vcc3v3_sys>;
> + vcc3-supply = <&vcc3v3_sys>;
> + vcc4-supply = <&vcc3v3_sys>;
> + vcc6-supply = <&vcc3v3_sys>;
> + vcc7-supply = <&vcc3v3_sys>;
> + vcc8-supply = <&vcc3v3_sys>;
> + vcc9-supply = <&vcc3v3_sys>;
> + vcc10-supply = <&vcc3v3_sys>;
> + vcc11-supply = <&vcc3v3_sys>;
> + vcc12-supply = <&vcc3v3_sys>;
> + vddio-supply = <&vcc1v8_pmu>;
> +
> + regulators {
> + vdd_center: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-name = "vdd_center";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_l: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-name = "vdd_cpu_l";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v0_tp: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc3v0_tp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_pmu: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_sd: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_sd";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcca3v0_codec: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcca3v0_codec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vcc_1v5";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1500000>;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_codec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v0: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc_3v0";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc3v3_s3: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc3v3_s3";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_s0: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc3v3_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <300>;
> + i2c-scl-falling-time-ns = <15>;
> +
> + gsl3673: gsl3673 at 40 {
> + compatible = "GSL,GSL3673";
> + reg = <0x40>;
> + screen_max_x = <1536>;
> + screen_max_y = <2048>;
> + irq_gpio_number = <&gpio1 20 IRQ_TYPE_LEVEL_LOW>;
> + rst_gpio_number = <&gpio4 22 GPIO_ACTIVE_HIGH>;
Again doesn't look like a valid binding.
> + };
> +
> + rt5640: rt5640 at 1c {
> + #sound-dai-cells = <0>;
> + compatible = "realtek,rt5640";
> + reg = <0x1c>;
> + clocks = <&cru SCLK_I2S_8CH_OUT>;
> + clock-names = "mclk";
> + realtek,in1-differential;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rt5640_hpcon>;
> + hp-con-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> + //hp-det-gpio = <&gpio4 28 GPIO_ACTIVE_LOW>;
don't add commented lines please
> + io-channels = <&saradc 4>;
> + hp-det-adc-value = <500>;
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> +};
> +
> +&i2c4 {
> + status = "okay";
> + i2c-scl-rising-time-ns = <600>;
> + i2c-scl-falling-time-ns = <20>;
> +
> + fusb0: fusb30x at 22 {
> + compatible = "fairchild,fusb302";
Has this made its way into the kernel yet?
Heiko
More information about the linux-arm-kernel
mailing list