[PATCH v4 1/8] phy: phy-mt65xx-usb3: improve RX detection stable time

[Chunfeng Yun]

Hi Kishon,

    Do you have any comments or suggestions on the series of patches?

Thanks a lot

On Sat, 2017-03-11 at 14:22 +0800, Chunfeng Yun wrote:
> The default value of RX detection stable time is 10us, and this
> margin is too big for some critical cases which cause U3 link fail
> and link to U2(probability is about 1%). So change it to 5us.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> ---
>  drivers/phy/phy-mt65xx-usb3.c |   18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> index d972067..fe2392a 100644
> --- a/drivers/phy/phy-mt65xx-usb3.c
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -112,6 +112,14 @@
>  #define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
>  #define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
>  
> +#define U3P_U3_PHYD_RXDET1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x128)
> +#define P3D_RG_RXDET_STB2_SET		GENMASK(17, 9)
> +#define P3D_RG_RXDET_STB2_SET_VAL(x)	((0x1ff & (x)) << 9)
> +
> +#define U3P_U3_PHYD_RXDET2		(SSUSB_SIFSLV_U3PHYD_BASE + 0x12c)
> +#define P3D_RG_RXDET_STB2_SET_P3	GENMASK(8, 0)
> +#define P3D_RG_RXDET_STB2_SET_P3_VAL(x)	(0x1ff & (x))
> +
>  #define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
>  #define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
>  #define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
> @@ -295,6 +303,16 @@ static void phy_instance_init(struct mt65xx_u3phy *u3phy,
>  	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
>  	writel(tmp, port_base + U3P_PHYD_CDR1);
>  
> +	tmp = readl(port_base + U3P_U3_PHYD_RXDET1);
> +	tmp &= ~P3D_RG_RXDET_STB2_SET;
> +	tmp |= P3D_RG_RXDET_STB2_SET_VAL(0x10);
> +	writel(tmp, port_base + U3P_U3_PHYD_RXDET1);
> +
> +	tmp = readl(port_base + U3P_U3_PHYD_RXDET2);
> +	tmp &= ~P3D_RG_RXDET_STB2_SET_P3;
> +	tmp |= P3D_RG_RXDET_STB2_SET_P3_VAL(0x10);
> +	writel(tmp, port_base + U3P_U3_PHYD_RXDET2);
> +
>  	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
>  }
>