[PATCH] arm64: dts: updated sata node on ls1012a dts

[Andy Tang]

Please ignore it. Send the wrong patch.
Sorry about it.

Regards,
Yuantian

> -----Original Message-----
> From: Yuantian Tang [mailto:andy.tang at nxp.com]
> Sent: Friday, March 10, 2017 4:12 PM
> To: shawnguo at kernel.org
> Cc: robh+dt at kernel.org; mark.rutland at arm.com; catalin.marinas at arm.com;
> will.deacon at arm.com; devicetree at vger.kernel.org; linux-arm-
> kernel at lists.infradead.org; Andy Tang
> Subject: [PATCH] arm64: dts: updated sata node on ls1012a dts
> 
> On ls1012a soc, sata ecc should be disabled. So added sata ecc register
> address so that driver can get this information.
> 
> Signed-off-by: Tang Yuantian <andy.tang at nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 80
> +++++++++++++++++++++++++-
>  1 file changed, 79 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index cffebb4..1870dde 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -43,6 +43,7 @@
>   */
> 
>  #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/thermal/thermal.h>
> 
>  / {
>  	compatible = "fsl,ls1012a";
> @@ -126,6 +127,81 @@
>  			#clock-cells = <2>;
>  			clocks = <&sysclk>;
>  		};
> +		tmu: tmu at 1f00000 {
> +			compatible = "fsl,qoriq-tmu";
> +			reg = <0x0 0x1f00000 0x0 0x10000>;
> +			interrupts = <0 33 0x4>;
> +			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
> +			fsl,tmu-calibration = <0x00000000 0x00000026
> +					       0x00000001 0x0000002d
> +					       0x00000002 0x00000032
> +					       0x00000003 0x00000039
> +					       0x00000004 0x0000003f
> +					       0x00000005 0x00000046
> +					       0x00000006 0x0000004d
> +					       0x00000007 0x00000054
> +					       0x00000008 0x0000005a
> +					       0x00000009 0x00000061
> +					       0x0000000a 0x0000006a
> +					       0x0000000b 0x00000071
> +
> +					       0x00010000 0x00000025
> +					       0x00010001 0x0000002c
> +					       0x00010002 0x00000035
> +					       0x00010003 0x0000003d
> +					       0x00010004 0x00000045
> +					       0x00010005 0x0000004e
> +					       0x00010006 0x00000057
> +					       0x00010007 0x00000061
> +					       0x00010008 0x0000006b
> +					       0x00010009 0x00000076
> +
> +					       0x00020000 0x00000029
> +					       0x00020001 0x00000033
> +					       0x00020002 0x0000003d
> +					       0x00020003 0x00000049
> +					       0x00020004 0x00000056
> +					       0x00020005 0x00000061
> +					       0x00020006 0x0000006d
> +
> +					       0x00030000 0x00000021
> +					       0x00030001 0x0000002a
> +					       0x00030002 0x0000003c
> +					       0x00030003 0x0000004e>;
> +			big-endian;
> +			#thermal-sensor-cells = <1>;
> +		};
> +
> +		thermal-zones {
> +			cpu_thermal: cpu-thermal {
> +				polling-delay-passive = <1000>;
> +				polling-delay = <5000>;
> +
> +				thermal-sensors = <&tmu 0>;
> +
> +				trips {
> +					cpu_alert: cpu-alert {
> +						temperature = <85000>;
> +						hysteresis = <2000>;
> +						type = "passive";
> +					};
> +					cpu_crit: cpu-crit {
> +						temperature = <95000>;
> +						hysteresis = <2000>;
> +						type = "critical";
> +					};
> +				};
> +
> +				cooling-maps {
> +					map0 {
> +						trip = <&cpu_alert>;
> +						cooling-device =
> +							<&cpu0
> THERMAL_NO_LIMIT
> +
> 	THERMAL_NO_LIMIT>;
> +					};
> +				};
> +			};
> +		};
> 
>  		i2c0: i2c at 2180000 {
>  			compatible = "fsl,vf610-i2c";
> @@ -238,7 +314,9 @@
> 
>  		sata: sata at 3200000 {
>  			compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
> -			reg = <0x0 0x3200000 0x0 0x10000>;
> +			reg = <0x0 0x3200000 0x0 0x10000>,
> +				<0x0 0x20140520 0x0 0x4>;
> +			reg-names = "ahci", "sata-ecc";
>  			interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&clockgen 4 0>;
>  			status = "disabled";
> --
> 2.1.0.27.g96db324