[PATCH 4/5] clk: sunxi-ng: Add driver for A83T CCU

[Maxime Ripard]

Hi Stephen

On Wed, Mar 01, 2017 at 11:17:05AM -0800, Stephen Boyd wrote:
> On 02/15, Maxime Ripard wrote:
> > On Tue, Feb 14, 2017 at 06:26:39PM +0800, Chen-Yu Tsai wrote:
> > > On Tue, Feb 14, 2017 at 5:58 PM, Maxime Ripard
> > > <maxime.ripard at free-electrons.com> wrote:
> > > > On Tue, Feb 14, 2017 at 11:35:25AM +0800, Chen-Yu Tsai wrote:
> > > >> +/*
> > > >> + * MMC2 supports what's called the "new timing mode". The CCU and the MMC
> > > >> + * controller must be in sync about which mode is used. The new mode moves
> > > >> + * the clock delay controls (and possibly the delay lines) into the MMC
> > > >> + * block. Also, the output of the clock is divided by 2. The output and
> > > >> + * sample phase clocks are unused under this mode.
> > > >> + *
> > > >> + * This new mode seems to be preferred. Hence we force this clock to the
> > > >> + * new mode. And we don't add the phase clocks.
> > > >> + */
> > > >
> > > > I'm sorry, but I said this several times, this isn't working. We
> > > > should model it properly, and not hack this around in the clock
> > > > driver.
> > > >
> > > > As you say in your comment, the MMC driver needs to be aware about
> > > > which mode is used, in order to also set a bit in one of its registers
> > > > accordingly, and modify its sampling behaviour.
> > > >
> > > > The new timing is preferred, but our previous clock implementations
> > > > didn't hardcode it, so we can't even rely on that behaviour to always
> > > > write it in our driver.
> > > 
> > > Correct. With the A83T there has never been a merged clock driver though.
> > > I realize this is a one off thing.
> > > 
> > > > This is not something specific to the A83T, but is found in all the
> > > > SoCs since the A23, so we need to come up with a good solution to
> > > > address that.
> > > >
> > > > I'm not sure what a good solution would be though. One would be to
> > > > just have a private function of our own to switch in the new mode (if
> > > > relevant, because only the MMC2 controllers have it), but that would
> > > > lead to troubles with !sunxi-ng. Not something we can't deal with, but
> > > > some extra precautions should be taken (make sure to protect the call
> > > > through an ifdef / IS_DEFINED, check that the sunxi-ng driver has been
> > > > probed, etc.)
> > > 
> > > If the custom function route is acceptable, I'll come up with something.
> > 
> > I think it would be a great start yes. I'll try to discuss it with
> > Mike and Stephen at ELC and see what they think about that.
> > 
> 
> I didn't hear anything at ELC.

Yeah, sorry, I ended up discussing this with Mike.

> Can someone explain what the issue is? Could something like
> clk_get_phase() + clk_get_rate() tell us if we're in one mode
> vs. the other?

So we have two modes of operation for that clock, old vs new (I know,
I didn't pick the names).

The old mode is what we support right now. It has a combination of a
linear multiplier and divider, plus some phase controls.

The new mode however disables the phase controls and adds post-divider
of 2 on the rate.

We cannot really rely on the rate itself, since there's a huge overlap
between the rates we can obtain in the old and new modes. Same thing
for the phase, having a 0 deg phase is achieved both in the old and
new modes.

To make things worse, the new mode is only available on one out of
three MMC controllers (and associated clocks), and that MMC controller
needs to set a bit as well to switch to the new mode if needed. So we
definitely needs some synchronisation there, and also to be able to
retrieve if the mode switching is available, and if we're already
using that mode.

Mike agreed that the easiest way forward was to use a custom function.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170303/09254849/attachment.sig>