[Devel] [RESEND PATCH v9 3/3] iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #126

[Geetha Akula]

On Tue, Jun 27, 2017 at 7:36 PM, Will Deacon <will.deacon at arm.com> wrote:
> On Tue, Jun 27, 2017 at 03:56:10PM +0200, Robert Richter wrote:
>> On 23.06.17 19:04:36, Geetha sowjanya wrote:
>> > From: Geetha Sowjanya <geethasowjanya.akula at cavium.com>
>> >
>> > Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
>> > lines for gerror, eventq and cmdq-sync.
>> >
>> > New named irq "combined" is set as a errata workaround, which allows to
>> > share the irq line by register single irq handler for all the interrupts.
>> >
>> > Signed-off-by: Geetha sowjanya <gakula at caviumnetworks.com>
>> > ---
>> >  Documentation/arm64/silicon-errata.txt             |    1 +
>> >  .../devicetree/bindings/iommu/arm,smmu-v3.txt      |    6 +
>> >  drivers/acpi/arm64/iort.c                          |   57 ++++++++---
>> >  drivers/iommu/arm-smmu-v3.c                        |  100 ++++++++++++++-----
>> >  4 files changed, 121 insertions(+), 43 deletions(-)
>>
>> > +static int arm_smmu_setup_irqs(struct arm_smmu_device *smmu)
>> > +{
>> > +   int ret, irq;
>> > +   u32 irqen_flags = IRQ_CTRL_EVTQ_IRQEN | IRQ_CTRL_GERROR_IRQEN;
>> > +
>> > +   /* Disable IRQs first */
>> > +   ret = arm_smmu_write_reg_sync(smmu, 0, ARM_SMMU_IRQ_CTRL,
>> > +                                 ARM_SMMU_IRQ_CTRLACK);
>> > +   if (ret) {
>> > +           dev_err(smmu->dev, "failed to disable irqs\n");
>> > +           return ret;
>> > +   }
>> > +
>> > +   irq = smmu->combined_irq;
>> > +   if (irq) {
>> > +           /*
>> > +            * Cavium ThunderX2 implementation doesn't not support unique
>> > +            * irq lines. Use single irq line for all the SMMUv3 interrupts.
>> > +            */
>> > +           ret = devm_request_threaded_irq(smmu->dev, irq,
>> > +                                   arm_smmu_combined_irq_handler,
>> > +                                   arm_smmu_combined_irq_thread,
>> > +                                   IRQF_ONESHOT,
>>
>> Without the IRQF_SHARED flag set I see the following on a dual node
>> system now:
Node1 SMMU interrupts are programmed wrong in the firmware.
Node 0 and Node1 SMMU do not share interrupts.
I have verified the patch on dual node with correct interrupt numbers
programmed in firmware.


Thanks,
Geetha.
>
> We asked about that before:
>
> https://marc.info/?l=linux-arm-kernel&m=149803613513068&w=2
> https://marc.info/?l=linux-acpi&m=149803744713475&w=2
>
> and Geetha didn't reply, but the next version of the patch dropped the flag.
> Is it just that firmware is misprogramming something here, or something
> more fundamental?
>
> Will