[PATCH v4] drm/sun4i: hdmi: Implement I2C adapter for A10s DDC bus
Jonathan Liu
net147 at gmail.com
Tue Jun 27 06:34:54 PDT 2017
Hi Maxime,
On 27 June 2017 at 05:05, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> On Sat, Jun 24, 2017 at 04:10:54PM +1000, Jonathan Liu wrote:
>> The documentation for drm_do_get_edid in drivers/gpu/drm/drm_edid.c states:
>> "As in the general case the DDC bus is accessible by the kernel at the I2C
>> level, drivers must make all reasonable efforts to expose it as an I2C
>> adapter and use drm_get_edid() instead of abusing this function."
>>
>> Exposing the DDC bus as an I2C adapter is more beneficial as it can be used
>> for purposes other than reading the EDID such as modifying the EDID or
>> using the HDMI DDC pins as an I2C bus through the I2C dev interface from
>> userspace (e.g. i2c-tools).
>>
>> Implement this for A10s.
>>
>> Signed-off-by: Jonathan Liu <net147 at gmail.com>
>> ---
>> Changes for v4:
>> - Carry over copyright from initial I2C code into sun4i_hdmi_i2c.c
>> - Clean up indentation in sun4i_hdmi.h
>> - Rename SUN4I_HDMI_DDC_MAX_TRANSFER_SIZE to SUN4I_HDMI_DDC_BYTE_COUNT_MAX
>> and group it under the SUN4I_HDMI_DDC_BYTE_COUNT_REG define, changing the
>> value to use the GENMASK macro to make it clear that it is derived from
>> the width of the field in the register
>> - Fix SUN4I_HDMI_DDC_INT_STATUS_DDC_TX_FIFO_UNDERFLOW typo which should be
>> SUN4I_HDMI_DDC_INT_STATUS_DDC_TX_FIFO_OVERFLOW
>> - Remove redundant rewriting of SUN4I_HDMI_DDC_INT_STATUS_REG register
>> - Change struct i2c_adapter to be const by using devm_kmemdup on creation
>> - Return -ETIMEDOUT instead of -EIO if there is timeout while transferring an
>> I2C message
>> - Instead of waiting for 1-2 bytes to transfer, wait for the time it would
>> take for remaining bytes to transfer (limited by FIFO size)
>> - Add additional comments
>>
>> Changes for v3:
>> - Explain why drm_do_get_edid should be used and why it's better to expose it
>> as an I2C adapter in commit message
>> - Reorder bit defines in descending order for consistency
>> - Keep old unused macros instead of removing them
>> - The v2 algorithm split large transfers into 16 byte transfers but this may
>> cause a large single write to be treated as multiple writes causing data
>> corruption. The algorithm has been reworked to not split larger transfers
>> and make more use of the FIFO to avoid this.
>> - Moved the creation of the DDC clock from sun4i_hdmi_enc.c to
>> sun4i_hdmi_i2c.c
>> - Reformatted code
>> - Instead of masking bits that we don't want to check for errors, explicitly
>> check the error bits
>> - Clear error bits at start of transfer in case of error from previous transfer
>> - Poll for completion of FIFO clear after setting FIFO clear bit
>>
>> Changes for v2:
>> - Rebased against Maxime's sunxi-drm/for-next branch
>> - Fix up error paths in sun4i_hdmi_bind so that the I2C adapter is deleted if
>> any of the calls after the I2C adapter is created fails
>> - Remove unnecessary includes in sun4i_hdmi_i2c.c
>>
>> drivers/gpu/drm/sun4i/Makefile | 1 +
>> drivers/gpu/drm/sun4i/sun4i_hdmi.h | 23 ++++
>> drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c | 101 ++------------
>> drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c | 242 +++++++++++++++++++++++++++++++++
>> 4 files changed, 277 insertions(+), 90 deletions(-)
>> create mode 100644 drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c
>>
>> diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
>> index e29fd3a2ba9c..43c753cafc88 100644
>> --- a/drivers/gpu/drm/sun4i/Makefile
>> +++ b/drivers/gpu/drm/sun4i/Makefile
>> @@ -2,6 +2,7 @@ sun4i-drm-y += sun4i_drv.o
>> sun4i-drm-y += sun4i_framebuffer.o
>>
>> sun4i-drm-hdmi-y += sun4i_hdmi_enc.o
>> +sun4i-drm-hdmi-y += sun4i_hdmi_i2c.o
>> sun4i-drm-hdmi-y += sun4i_hdmi_ddc_clk.o
>> sun4i-drm-hdmi-y += sun4i_hdmi_tmds_clk.o
>>
>> diff --git a/drivers/gpu/drm/sun4i/sun4i_hdmi.h b/drivers/gpu/drm/sun4i/sun4i_hdmi.h
>> index 2f2f2ff1ea63..eaff92fe236c 100644
>> --- a/drivers/gpu/drm/sun4i/sun4i_hdmi.h
>> +++ b/drivers/gpu/drm/sun4i/sun4i_hdmi.h
>> @@ -96,6 +96,7 @@
>> #define SUN4I_HDMI_DDC_CTRL_ENABLE BIT(31)
>> #define SUN4I_HDMI_DDC_CTRL_START_CMD BIT(30)
>> #define SUN4I_HDMI_DDC_CTRL_FIFO_DIR_MASK BIT(8)
>> +#define SUN4I_HDMI_DDC_CTRL_FIFO_DIR_WRITE (1 << 8)
>> #define SUN4I_HDMI_DDC_CTRL_FIFO_DIR_READ (0 << 8)
>> #define SUN4I_HDMI_DDC_CTRL_RESET BIT(0)
>>
>> @@ -105,14 +106,33 @@
>> #define SUN4I_HDMI_DDC_ADDR_OFFSET(off) (((off) & 0xff) << 8)
>> #define SUN4I_HDMI_DDC_ADDR_SLAVE(addr) ((addr) & 0xff)
>>
>> +#define SUN4I_HDMI_DDC_INT_STATUS_REG 0x50c
>> +#define SUN4I_HDMI_DDC_INT_STATUS_ILLEGAL_FIFO_OPERATION BIT(7)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_DDC_RX_FIFO_UNDERFLOW BIT(6)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_DDC_TX_FIFO_OVERFLOW BIT(5)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_FIFO_REQUEST BIT(4)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_ARBITRATION_ERROR BIT(3)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_ACK_ERROR BIT(2)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_BUS_ERROR BIT(1)
>> +#define SUN4I_HDMI_DDC_INT_STATUS_TRANSFER_COMPLETE BIT(0)
>> +
>> #define SUN4I_HDMI_DDC_FIFO_CTRL_REG 0x510
>> #define SUN4I_HDMI_DDC_FIFO_CTRL_CLEAR BIT(31)
>>
>> +#define SUN4I_HDMI_DDC_FIFO_STATUS_REG 0x514
>> +#define SUN4I_HDMI_DDC_FIFO_STATUS_FULL BIT(6)
>> +#define SUN4I_HDMI_DDC_FIFO_STATUS_EMPTY BIT(5)
>> +#define SUN4I_HDMI_DDC_FIFO_STATUS_LEVEL_MASK GENMASK(4, 0)
>> +
>> #define SUN4I_HDMI_DDC_FIFO_DATA_REG 0x518
>> +
>> #define SUN4I_HDMI_DDC_BYTE_COUNT_REG 0x51c
>> +#define SUN4I_HDMI_DDC_BYTE_COUNT_MAX GENMASK(9, 0)
>>
>> #define SUN4I_HDMI_DDC_CMD_REG 0x520
>> #define SUN4I_HDMI_DDC_CMD_EXPLICIT_EDDC_READ 6
>> +#define SUN4I_HDMI_DDC_CMD_IMPLICIT_READ 5
>> +#define SUN4I_HDMI_DDC_CMD_IMPLICIT_WRITE 3
>>
>> #define SUN4I_HDMI_DDC_CLK_REG 0x528
>> #define SUN4I_HDMI_DDC_CLK_M(m) (((m) & 0x7) << 3)
>> @@ -146,6 +166,8 @@ struct sun4i_hdmi {
>> struct clk *ddc_clk;
>> struct clk *tmds_clk;
>>
>> + struct i2c_adapter *i2c;
>> +
>> struct sun4i_drv *drv;
>>
>> bool hdmi_monitor;
>> @@ -153,5 +175,6 @@ struct sun4i_hdmi {
>>
>> int sun4i_ddc_create(struct sun4i_hdmi *hdmi, struct clk *clk);
>> int sun4i_tmds_create(struct sun4i_hdmi *hdmi);
>> +int sun4i_hdmi_i2c_create(struct device *dev, struct sun4i_hdmi *hdmi);
>>
>> #endif /* _SUN4I_HDMI_H_ */
>> diff --git a/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c b/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
>> index d3398f6250ef..b74607feb35c 100644
>> --- a/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
>> +++ b/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
>> @@ -29,8 +29,6 @@
>> #include "sun4i_hdmi.h"
>> #include "sun4i_tcon.h"
>>
>> -#define DDC_SEGMENT_ADDR 0x30
>> -
>> static inline struct sun4i_hdmi *
>> drm_encoder_to_sun4i_hdmi(struct drm_encoder *encoder)
>> {
>> @@ -184,93 +182,13 @@ static const struct drm_encoder_funcs sun4i_hdmi_funcs = {
>> .destroy = drm_encoder_cleanup,
>> };
>>
>> -static int sun4i_hdmi_read_sub_block(struct sun4i_hdmi *hdmi,
>> - unsigned int blk, unsigned int offset,
>> - u8 *buf, unsigned int count)
>> -{
>> - unsigned long reg;
>> - int i;
>> -
>> - reg = readl(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> - reg &= ~SUN4I_HDMI_DDC_CTRL_FIFO_DIR_MASK;
>> - writel(reg | SUN4I_HDMI_DDC_CTRL_FIFO_DIR_READ,
>> - hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> -
>> - writel(SUN4I_HDMI_DDC_ADDR_SEGMENT(offset >> 8) |
>> - SUN4I_HDMI_DDC_ADDR_EDDC(DDC_SEGMENT_ADDR << 1) |
>> - SUN4I_HDMI_DDC_ADDR_OFFSET(offset) |
>> - SUN4I_HDMI_DDC_ADDR_SLAVE(DDC_ADDR),
>> - hdmi->base + SUN4I_HDMI_DDC_ADDR_REG);
>> -
>> - reg = readl(hdmi->base + SUN4I_HDMI_DDC_FIFO_CTRL_REG);
>> - writel(reg | SUN4I_HDMI_DDC_FIFO_CTRL_CLEAR,
>> - hdmi->base + SUN4I_HDMI_DDC_FIFO_CTRL_REG);
>> -
>> - writel(count, hdmi->base + SUN4I_HDMI_DDC_BYTE_COUNT_REG);
>> - writel(SUN4I_HDMI_DDC_CMD_EXPLICIT_EDDC_READ,
>> - hdmi->base + SUN4I_HDMI_DDC_CMD_REG);
>> -
>> - reg = readl(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> - writel(reg | SUN4I_HDMI_DDC_CTRL_START_CMD,
>> - hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> -
>> - if (readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG, reg,
>> - !(reg & SUN4I_HDMI_DDC_CTRL_START_CMD),
>> - 100, 100000))
>> - return -EIO;
>> -
>> - for (i = 0; i < count; i++)
>> - buf[i] = readb(hdmi->base + SUN4I_HDMI_DDC_FIFO_DATA_REG);
>> -
>> - return 0;
>> -}
>> -
>> -static int sun4i_hdmi_read_edid_block(void *data, u8 *buf, unsigned int blk,
>> - size_t length)
>> -{
>> - struct sun4i_hdmi *hdmi = data;
>> - int retry = 2, i;
>> -
>> - do {
>> - for (i = 0; i < length; i += SUN4I_HDMI_DDC_FIFO_SIZE) {
>> - unsigned char offset = blk * EDID_LENGTH + i;
>> - unsigned int count = min((unsigned int)SUN4I_HDMI_DDC_FIFO_SIZE,
>> - length - i);
>> - int ret;
>> -
>> - ret = sun4i_hdmi_read_sub_block(hdmi, blk, offset,
>> - buf + i, count);
>> - if (ret)
>> - return ret;
>> - }
>> - } while (!drm_edid_block_valid(buf, blk, true, NULL) && (retry--));
>> -
>> - return 0;
>> -}
>> -
>> static int sun4i_hdmi_get_modes(struct drm_connector *connector)
>> {
>> struct sun4i_hdmi *hdmi = drm_connector_to_sun4i_hdmi(connector);
>> - unsigned long reg;
>> struct edid *edid;
>> int ret;
>>
>> - /* Reset i2c controller */
>> - writel(SUN4I_HDMI_DDC_CTRL_ENABLE | SUN4I_HDMI_DDC_CTRL_RESET,
>> - hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> - if (readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG, reg,
>> - !(reg & SUN4I_HDMI_DDC_CTRL_RESET),
>> - 100, 2000))
>> - return -EIO;
>> -
>> - writel(SUN4I_HDMI_DDC_LINE_CTRL_SDA_ENABLE |
>> - SUN4I_HDMI_DDC_LINE_CTRL_SCL_ENABLE,
>> - hdmi->base + SUN4I_HDMI_DDC_LINE_CTRL_REG);
>> -
>> - clk_prepare_enable(hdmi->ddc_clk);
>> - clk_set_rate(hdmi->ddc_clk, 100000);
>> -
>> - edid = drm_do_get_edid(connector, sun4i_hdmi_read_edid_block, hdmi);
>> + edid = drm_get_edid(connector, hdmi->i2c);
>> if (!edid)
>> return 0;
>>
>> @@ -282,8 +200,6 @@ static int sun4i_hdmi_get_modes(struct drm_connector *connector)
>> ret = drm_add_edid_modes(connector, edid);
>> kfree(edid);
>>
>> - clk_disable_unprepare(hdmi->ddc_clk);
>> -
>> return ret;
>> }
>>
>> @@ -407,9 +323,9 @@ static int sun4i_hdmi_bind(struct device *dev, struct device *master,
>> SUN4I_HDMI_PLL_CTRL_PLL_EN;
>> writel(reg, hdmi->base + SUN4I_HDMI_PLL_CTRL_REG);
>>
>> - ret = sun4i_ddc_create(hdmi, hdmi->tmds_clk);
>> + ret = sun4i_hdmi_i2c_create(dev, hdmi);
>> if (ret) {
>> - dev_err(dev, "Couldn't create the DDC clock\n");
>> + dev_err(dev, "Couldn't create the HDMI I2C adapter\n");
>> return ret;
>> }
>>
>> @@ -422,13 +338,15 @@ static int sun4i_hdmi_bind(struct device *dev, struct device *master,
>> NULL);
>> if (ret) {
>> dev_err(dev, "Couldn't initialise the HDMI encoder\n");
>> - return ret;
>> + goto err_del_i2c_adapter;
>> }
>>
>> hdmi->encoder.possible_crtcs = drm_of_find_possible_crtcs(drm,
>> dev->of_node);
>> - if (!hdmi->encoder.possible_crtcs)
>> - return -EPROBE_DEFER;
>> + if (!hdmi->encoder.possible_crtcs) {
>> + ret = -EPROBE_DEFER;
>> + goto err_del_i2c_adapter;
>> + }
>>
>> drm_connector_helper_add(&hdmi->connector,
>> &sun4i_hdmi_connector_helper_funcs);
>> @@ -451,6 +369,8 @@ static int sun4i_hdmi_bind(struct device *dev, struct device *master,
>>
>> err_cleanup_connector:
>> drm_encoder_cleanup(&hdmi->encoder);
>> +err_del_i2c_adapter:
>> + i2c_del_adapter(hdmi->i2c);
>> return ret;
>> }
>>
>> @@ -461,6 +381,7 @@ static void sun4i_hdmi_unbind(struct device *dev, struct device *master,
>>
>> drm_connector_cleanup(&hdmi->connector);
>> drm_encoder_cleanup(&hdmi->encoder);
>> + i2c_del_adapter(hdmi->i2c);
>> }
>>
>> static const struct component_ops sun4i_hdmi_ops = {
>> diff --git a/drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c b/drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c
>> new file mode 100644
>> index 000000000000..45cfd6bf483c
>> --- /dev/null
>> +++ b/drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c
>> @@ -0,0 +1,242 @@
>> +/*
>> + * Copyright (C) 2016 Maxime Ripard <maxime.ripard at free-electrons.com>
>> + * Copyright (C) 2017 Jonathan Liu <net147 at gmail.com>
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/i2c.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/ktime.h>
>> +
>> +#include "sun4i_hdmi.h"
>> +
>> +#define SUN4I_HDMI_DDC_INT_STATUS_ERROR_MASK ( \
>> + SUN4I_HDMI_DDC_INT_STATUS_ILLEGAL_FIFO_OPERATION | \
>> + SUN4I_HDMI_DDC_INT_STATUS_DDC_RX_FIFO_UNDERFLOW | \
>> + SUN4I_HDMI_DDC_INT_STATUS_DDC_TX_FIFO_OVERFLOW | \
>> + SUN4I_HDMI_DDC_INT_STATUS_ARBITRATION_ERROR | \
>> + SUN4I_HDMI_DDC_INT_STATUS_ACK_ERROR | \
>> + SUN4I_HDMI_DDC_INT_STATUS_BUS_ERROR \
>> +)
>> +
>> +static int wait_fifo_flag_unset(struct sun4i_hdmi *hdmi, int len, u32 flag)
>> +{
>> + /* 1 byte takes 9 clock cycles (8 bits + 1 ack) */
>> + unsigned long byte_time = DIV_ROUND_UP(USEC_PER_SEC,
>> + clk_get_rate(hdmi->ddc_clk)) * 9;
>> + u32 reg;
>> + ktime_t wait_timeout = ktime_add_us(ktime_get(), 100000);
>> +
>> + for (;;) {
>> + /* Check for errors */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_INT_STATUS_REG);
>> + if (reg & SUN4I_HDMI_DDC_INT_STATUS_ERROR_MASK)
>> + return -EIO;
>> +
>> + /* Check if requested FIFO flag is unset */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_FIFO_STATUS_REG);
>> + if (!(reg & flag))
>> + break;
>> +
>> + /* Timeout */
>> + if (ktime_compare(ktime_get(), wait_timeout) > 0)
>> + return -ETIMEDOUT;
>> +
>> + /* Wait for bytes to transfer (limited by FIFO size) */
>> + usleep_range(byte_time,
>> + min(len, SUN4I_HDMI_DDC_FIFO_SIZE) * byte_time);
>> + }
>> +
>> + /* Return FIFO level */
>> + return (int)(reg & SUN4I_HDMI_DDC_FIFO_STATUS_LEVEL_MASK);
>> +}
>
> I still think you should be using readl_poll_timeout here, and then
> check for errors. This is both easier to understand and you avoid an
> unneeded duplication.
>
I will rework to use readl_poll_timeout.
>> +
>> +static int wait_fifo_read_ready(struct sun4i_hdmi *hdmi, int len)
>> +{
>> + int level = wait_fifo_flag_unset(hdmi, len,
>> + SUN4I_HDMI_DDC_FIFO_STATUS_EMPTY);
>> +
>> + /* Return number of bytes that can be read from FIFO */
>> + return min(len, level);
>> +}
>
> The function's name is still inconsistent with what it does, and
> returns.
>
Will no longer be needed after reworking to use readl_poll_timeout.
>> +
>> +static int wait_fifo_write_ready(struct sun4i_hdmi *hdmi, int len)
>> +{
>> + int level = wait_fifo_flag_unset(hdmi, len,
>> + SUN4I_HDMI_DDC_FIFO_STATUS_FULL);
>> +
>> + /* Return number of bytes that can be written to FIFO */
>> + return min(len, SUN4I_HDMI_DDC_FIFO_SIZE - level);
>> +}
>
> Same thing here.
>
Will no longer be needed after reworking to use readl_poll_timeout.
>> +static int xfer_msg(struct sun4i_hdmi *hdmi, struct i2c_msg *msg)
>> +{
>> + int i, len;
>> + u32 reg;
>> +
>> + /* Clear errors */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_INT_STATUS_REG);
>> + reg &= ~SUN4I_HDMI_DDC_INT_STATUS_ERROR_MASK;
>> + writel(reg, hdmi->base + SUN4I_HDMI_DDC_INT_STATUS_REG);
>> +
>> + /* Set FIFO direction */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> + reg &= ~SUN4I_HDMI_DDC_CTRL_FIFO_DIR_MASK;
>> + reg |= (msg->flags & I2C_M_RD) ?
>> + SUN4I_HDMI_DDC_CTRL_FIFO_DIR_READ :
>> + SUN4I_HDMI_DDC_CTRL_FIFO_DIR_WRITE;
>> + writel(reg, hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> +
>> + /* Set I2C address */
>> + writel(SUN4I_HDMI_DDC_ADDR_SLAVE(msg->addr),
>> + hdmi->base + SUN4I_HDMI_DDC_ADDR_REG);
>> +
>> + /* Clear FIFO */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_FIFO_CTRL_REG);
>> + writel(reg | SUN4I_HDMI_DDC_FIFO_CTRL_CLEAR,
>> + hdmi->base + SUN4I_HDMI_DDC_FIFO_CTRL_REG);
>> + if (readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_FIFO_CTRL_REG,
>> + reg,
>> + !(reg & SUN4I_HDMI_DDC_FIFO_CTRL_CLEAR),
>> + 100, 100000))
>> + return -EIO;
>> +
>> + /* Set transfer length */
>> + writel(msg->len, hdmi->base + SUN4I_HDMI_DDC_BYTE_COUNT_REG);
>> +
>> + /* Set command */
>> + writel(msg->flags & I2C_M_RD ?
>> + SUN4I_HDMI_DDC_CMD_IMPLICIT_READ :
>> + SUN4I_HDMI_DDC_CMD_IMPLICIT_WRITE,
>> + hdmi->base + SUN4I_HDMI_DDC_CMD_REG);
>> +
>> + /* Start command */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> + writel(reg | SUN4I_HDMI_DDC_CTRL_START_CMD,
>> + hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> +
>> + /* Transfer bytes */
>> + if (msg->flags & I2C_M_RD) {
>> + for (i = 0; i < msg->len; i += len) {
>> + len = wait_fifo_read_ready(hdmi, msg->len - i);
>> + if (len <= 0)
>> + return len;
>> +
>> + readsb(hdmi->base + SUN4I_HDMI_DDC_FIFO_DATA_REG,
>> + msg->buf + i, len);
>> + }
>> + } else {
>> + for (i = 0; i < msg->len; i += len) {
>> + len = wait_fifo_write_ready(hdmi, msg->len - i);
>> + if (len <= 0)
>> + return len;
>> +
>> + writesb(hdmi->base + SUN4I_HDMI_DDC_FIFO_DATA_REG,
>> + msg->buf + i, len);
>> + }
>> + }
>> +
>> + /* Wait for command to finish */
>> + if (readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG,
>> + reg,
>> + !(reg & SUN4I_HDMI_DDC_CTRL_START_CMD),
>> + 100, 100000))
>> + return -EIO;
>> +
>> + /* Check for errors */
>> + reg = readl(hdmi->base + SUN4I_HDMI_DDC_INT_STATUS_REG);
>> + if ((reg & SUN4I_HDMI_DDC_INT_STATUS_ERROR_MASK) ||
>> + !(reg & SUN4I_HDMI_DDC_INT_STATUS_TRANSFER_COMPLETE)) {
>> + return -EIO;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int sun4i_hdmi_i2c_xfer(struct i2c_adapter *adap,
>> + struct i2c_msg *msgs, int num)
>> +{
>> + struct sun4i_hdmi *hdmi = i2c_get_adapdata(adap);
>> + u32 reg;
>> + int err, i, ret = num;
>> +
>> + for (i = 0; i < num; i++) {
>> + if (!msgs[i].len)
>> + return -EINVAL;
>> + if (msgs[i].len > SUN4I_HDMI_DDC_BYTE_COUNT_MAX)
>> + return -EINVAL;
>> + }
>> +
>> + /* Reset I2C controller */
>> + writel(SUN4I_HDMI_DDC_CTRL_ENABLE | SUN4I_HDMI_DDC_CTRL_RESET,
>> + hdmi->base + SUN4I_HDMI_DDC_CTRL_REG);
>> + if (readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_CTRL_REG, reg,
>> + !(reg & SUN4I_HDMI_DDC_CTRL_RESET),
>> + 100, 2000))
>> + return -EIO;
>> +
>> + writel(SUN4I_HDMI_DDC_LINE_CTRL_SDA_ENABLE |
>> + SUN4I_HDMI_DDC_LINE_CTRL_SCL_ENABLE,
>> + hdmi->base + SUN4I_HDMI_DDC_LINE_CTRL_REG);
>> +
>> + clk_prepare_enable(hdmi->ddc_clk);
>> + clk_set_rate(hdmi->ddc_clk, 100000);
>> +
>> + for (i = 0; i < num; i++) {
>> + err = xfer_msg(hdmi, &msgs[i]);
>> + if (err) {
>> + ret = err;
>> + break;
>> + }
>> + }
>> +
>> + clk_disable_unprepare(hdmi->ddc_clk);
>> + return ret;
>> +}
>> +
>> +static u32 sun4i_hdmi_i2c_func(struct i2c_adapter *adap)
>> +{
>> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
>> +}
>> +
>> +static const struct i2c_algorithm sun4i_hdmi_i2c_algorithm = {
>> + .master_xfer = sun4i_hdmi_i2c_xfer,
>> + .functionality = sun4i_hdmi_i2c_func,
>> +};
>> +
>> +static const struct i2c_adapter sun4i_hdmi_i2c_adapter = {
>> + .owner = THIS_MODULE,
>> + .class = I2C_CLASS_DDC,
>> + .algo = &sun4i_hdmi_i2c_algorithm,
>> + .name = "sun4i_hdmi_i2c adapter",
>> +};
>> +
>> +int sun4i_hdmi_i2c_create(struct device *dev, struct sun4i_hdmi *hdmi)
>> +{
>> + struct i2c_adapter *adap;
>> + int ret = 0;
>> +
>> + ret = sun4i_ddc_create(hdmi, hdmi->tmds_clk);
>> + if (ret)
>> + return ret;
>> +
>> + adap = devm_kmemdup(dev, &sun4i_hdmi_i2c_adapter,
>> + sizeof(sun4i_hdmi_i2c_adapter), GFP_KERNEL);
>
> It would be more consistent with what the kernel usually does to just
> kmalloc that structure, and fill it.
>
Ok.
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
Thanks for the reviews.
Regards,
Jonathan
More information about the linux-arm-kernel
mailing list