[PATCH v3 4/9] serial: atmel: Use common rs485 device tree parsing function

Richard Genoud richard.genoud at gmail.com
Tue Jun 27 01:27:25 PDT 2017


On 27/06/2017 09:41, Nicolas Ferre wrote:
> On 26/06/2017 at 11:07, Uwe Kleine-König wrote:
>> From: Sascha Hauer <s.hauer at pengutronix.de>
>>
>> We just got a common helper for parsing the rs485 specific
>> device tree properties. Use it and drop the open coded parser.
>>
>> Note that there is a small difference between the removed and the now
>> used implementation: The former cleared flags to 0 if rs485-rts-delay
>> was given, the common helper clears SER_RS485_RX_DURING_TX and
>> SER_RS485_ENABLED only but always which makes more sense.
> 
> Sure:
> Acked-by: Nicolas Ferre <nicolas.ferre at microchip.com>
> 
> Thanks Sasha and Uwe!
> 
Acked-by: Richard Genoud <richard.genoud at gmail.com>

Thanks !
>> Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
>> [ukleinek: point out semantic change in commit log]
>> Signed-off-by: Uwe Kleine-König <u.kleine-koenig at pengutronix.de>
>> ---
>>  drivers/tty/serial/atmel_serial.c | 25 +------------------------
>>  1 file changed, 1 insertion(+), 24 deletions(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index 937d67f22fba..245d9c227ad5 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -1684,29 +1684,6 @@ static void atmel_init_property(struct atmel_uart_port *atmel_port,
>>  	}
>>  }
>>  
>> -static void atmel_init_rs485(struct uart_port *port,
>> -				struct platform_device *pdev)
>> -{
>> -	struct device_node *np = pdev->dev.of_node;
>> -
>> -	struct serial_rs485 *rs485conf = &port->rs485;
>> -	u32 rs485_delay[2];
>> -
>> -	/* rs485 properties */
>> -	if (of_property_read_u32_array(np, "rs485-rts-delay",
>> -				       rs485_delay, 2) == 0) {
>> -		rs485conf->delay_rts_before_send = rs485_delay[0];
>> -		rs485conf->delay_rts_after_send = rs485_delay[1];
>> -		rs485conf->flags = 0;
>> -	}
>> -
>> -	if (of_get_property(np, "rs485-rx-during-tx", NULL))
>> -		rs485conf->flags |= SER_RS485_RX_DURING_TX;
>> -
>> -	if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
>> -		rs485conf->flags |= SER_RS485_ENABLED;
>> -}
>> -
>>  static void atmel_set_ops(struct uart_port *port)
>>  {
>>  	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>> @@ -2390,7 +2367,7 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
>>  	atmel_init_property(atmel_port, pdev);
>>  	atmel_set_ops(port);
>>  
>> -	atmel_init_rs485(port, pdev);
>> +	of_get_rs485_mode(pdev->dev.of_node, &port->rs485);
>>  
>>  	port->iotype		= UPIO_MEM;
>>  	port->flags		= UPF_BOOT_AUTOCONF | UPF_IOREMAP;
>>
> 
> 




More information about the linux-arm-kernel mailing list