[PATCH V4 5/7] pinctrl: imx: remove gpio_request_enable and gpio_disable_free
A.s. Dong
aisheng.dong at nxp.com
Mon Jun 26 22:27:57 PDT 2017
> -----Original Message-----
> From: Stefan Agner [mailto:stefan at agner.ch]
> Sent: Tuesday, June 27, 2017 11:48 AM
> To: A.s. Dong
> Cc: linux-gpio at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> linus.walleij at linaro.org; shawnguo at kernel.org; Jacky Bai; Andy Duan;
> kernel at pengutronix.de; Alexandre Courbot
> Subject: Re: [PATCH V4 5/7] pinctrl: imx: remove gpio_request_enable and
> gpio_disable_free
>
> On 2017-06-21 04:59, Dong Aisheng wrote:
> > gpio_request_enable/disable_free actually are not quite necessary as
> > standard IMX pinctrl binding already sets GPIO mux from device tree,
> > e.g. VF610_PAD_PTB20__GPIO_42 or MX7D_PAD_SD2_CD_B__GPIO5_IO9 No need
> > to do it again in gpio_request_enable.
> >
> > And according to Stefan:
> > "For all GPIO I checked in upstream device trees we assign a pinctrl
> > to the same node, so in all cases gpio_request_enable/disable is
> > really unnecessary."
> >
> > So it should be safe to simply remove it.
>
> Thanks looks good.
>
> I would add a comment that this changes semantics for Vybrid, e.g.
>
> "The two functions have been introduced for Vybrid (through
> SHARE_MUX_CONF_REG) and mux pins as GPIOs automatically when a GPIO gets
> requested. The automatic mux is optional by the pinmux/gpio subsystem
> semantics, and other NXP devices do not use it, instead an explicit
> pinctrl node is added in the device tree to mux GPIOs where required.
> Hence this change aligns Vybrid to other NXP (i.MX) devices.
>
> Note that all upstream device tree assign proper pinctrl properties where
> GPIOs are used so no change is necessary for device trees."
>
The comments looks ok to me.
Linus,
Would you help append it when pick the patch?
Stefan,
Would you help review imx7ulp GPIO patches as well after this pinctrl change?
Regards
Dong Aisheng
> Otherwise:
> Acked-by: Stefan Agner <stefan at agner.ch>
>
> --
> Stefan
>
> >
> > Cc: Stefan Agner <stefan at agner.ch>
> > Cc: Linus Walleij <linus.walleij at linaro.org>
> > Cc: Alexandre Courbot <gnurou at gmail.com>
> > Cc: Shawn Guo <shawnguo at kernel.org>
> > Cc: Fugang Duan <fugang.duan at nxp.com>
> > Cc: Bai Ping <ping.bai at nxp.com>
> > Signed-off-by: Dong Aisheng <aisheng.dong at nxp.com>
> >
> > ---
> > ChangeLog:
> > * New patch.
> > Instead of fixing gpio_request_enable/disable, we decided to remove
> it
> > after dicussion with Stefan (see blow).
> > https://www.spinics.net/lists/arm-kernel/msg583154.html
> > ---
> > drivers/pinctrl/freescale/pinctrl-imx.c | 69
> > ---------------------------------
> > 1 file changed, 69 deletions(-)
> >
> > diff --git a/drivers/pinctrl/freescale/pinctrl-imx.c
> > b/drivers/pinctrl/freescale/pinctrl-imx.c
> > index fc1ba3c..505fe79 100644
> > --- a/drivers/pinctrl/freescale/pinctrl-imx.c
> > +++ b/drivers/pinctrl/freescale/pinctrl-imx.c
> > @@ -255,73 +255,6 @@ static int imx_pmx_set(struct pinctrl_dev
> > *pctldev, unsigned selector,
> > return 0;
> > }
> >
> > -static int imx_pmx_gpio_request_enable(struct pinctrl_dev *pctldev,
> > - struct pinctrl_gpio_range *range, unsigned offset)
> > -{
> > - struct imx_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev);
> > - struct imx_pinctrl_soc_info *info = ipctl->info;
> > - const struct imx_pin_reg *pin_reg;
> > - struct group_desc *grp;
> > - struct imx_pin *imx_pin;
> > - unsigned int pin, group;
> > - u32 reg;
> > -
> > - /* Currently implementation only for shared mux/conf register */
> > - if (!(info->flags & SHARE_MUX_CONF_REG))
> > - return 0;
> > -
> > - pin_reg = &info->pin_regs[offset];
> > - if (pin_reg->mux_reg == -1)
> > - return -EINVAL;
> > -
> > - /* Find the pinctrl config with GPIO mux mode for the requested pin
> */
> > - for (group = 0; group < pctldev->num_groups; group++) {
> > - grp = pinctrl_generic_get_group(pctldev, group);
> > - if (!grp)
> > - continue;
> > - for (pin = 0; pin < grp->num_pins; pin++) {
> > - imx_pin = &((struct imx_pin *)(grp->data))[pin];
> > - if (imx_pin->pin == offset && !imx_pin->mux_mode)
> > - goto mux_pin;
> > - }
> > - }
> > -
> > - return -EINVAL;
> > -
> > -mux_pin:
> > - reg = readl(ipctl->base + pin_reg->mux_reg);
> > - reg &= ~info->mux_mask;
> > - reg |= imx_pin->config;
> > - writel(reg, ipctl->base + pin_reg->mux_reg);
> > -
> > - return 0;
> > -}
> > -
> > -static void imx_pmx_gpio_disable_free(struct pinctrl_dev *pctldev,
> > - struct pinctrl_gpio_range *range, unsigned offset)
> > -{
> > - struct imx_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev);
> > - struct imx_pinctrl_soc_info *info = ipctl->info;
> > - const struct imx_pin_reg *pin_reg;
> > - u32 reg;
> > -
> > - /*
> > - * Only Vybrid has the input/output buffer enable flags (IBE/OBE)
> > - * They are part of the shared mux/conf register.
> > - */
> > - if (!(info->flags & SHARE_MUX_CONF_REG))
> > - return;
> > -
> > - pin_reg = &info->pin_regs[offset];
> > - if (pin_reg->mux_reg == -1)
> > - return;
> > -
> > - /* Clear IBE/OBE/PUE to disable the pin (Hi-Z) */
> > - reg = readl(ipctl->base + pin_reg->mux_reg);
> > - reg &= ~0x7;
> > - writel(reg, ipctl->base + pin_reg->mux_reg);
> > -}
> > -
> > static int imx_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
> > struct pinctrl_gpio_range *range, unsigned offset, bool input)
> {
> > @@ -357,8 +290,6 @@ static const struct pinmux_ops imx_pmx_ops = {
> > .get_function_name = pinmux_generic_get_function_name,
> > .get_function_groups = pinmux_generic_get_function_groups,
> > .set_mux = imx_pmx_set,
> > - .gpio_request_enable = imx_pmx_gpio_request_enable,
> > - .gpio_disable_free = imx_pmx_gpio_disable_free,
> > .gpio_set_direction = imx_pmx_gpio_set_direction, };
More information about the linux-arm-kernel
mailing list