[PATCH 2/5] dt-bindings: phy-hisi-inno-usb2: add support for hisi-inno-usb2 phy

[Rob Herring]

On Wed, Jun 21, 2017 at 05:00:42PM +0800, Jiancheng Xue wrote:
> Add support for hisi-inno-usb2 phy.
> 
> Signed-off-by: Jiancheng Xue <xuejiancheng at hisilicon.com>
> ---
>  .../devicetree/bindings/phy/phy-hisi-inno-usb2.txt | 36 ++++++++++++++++++++++
>  1 file changed, 36 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> new file mode 100644
> index 0000000..21f8208
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> @@ -0,0 +1,36 @@
> +HiSilicon INNO USB2 PHY
> +-----------------------
> +Required properties:
> +- compatible: Should be one of the following strings:
> +		"hisilicon,inno-usb2-phy",
> +		"hisilicon,hi3798cv200-usb2-phy",
> +- #phy-cells: Must be 0
> +- hisilicon,peripheral-syscon: Phandle of syscon used to control phy.
> +- clocks: Phandle and clock specifier pair for reference clock utmi_refclk.
> +- resets: List of phandle and reset specifier pairs for each reset signal in
> +reset-names.
> +- reset-names: Should be "por_rst" and "test_rst". The test_rst only
> +exists in some of SOCs, so it is optional.

_rst is redundant.

> +
> +Phy node can include up to four subnodes. Each subnode represents one port.
> +The required properties of port node are as follows:
> +- clocks: Phandle and clock specifier pair for utmi_clock.
> +- resets: List of phandle and reset specifier pairs for port reset and utmi reset.
> +- reset-names: List of reset signal names. Should be "port_rst" and "utmi_rst"
> +
> +Refer to phy/phy-bindings.txt for the generic PHY binding properties
> +
> +Example:
> +usb_phy: phy {
> +		 compatible = "hisilicon,inno_usb2_phy";

Doesn't match the above compatible.

> +		 #phy-cells = <0>;
> +		 hisilicon,peripheral-syscon = <&peri_ctrl>;
> +		 clocks = <&crg USB2_REF_CLK>;
> +		 resets = <&crg 0xb4 2>;
> +		 reset-names = "por_rst";
> +		 port0 {

port at 0 and provide a reg property.

> +			 clocks = <&crg USB2_UTMI0_CLK>;
> +			 resets = <&crg 0xb4 5>, <&crg 0xb4 1>;
> +			 reset-names = "port_rst", "utmi_rst";
> +		 };
> +	 };
> -- 
> 1.9.1
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html