[PATCH v5 4/4] iio: adc: at91-sama5d2_adc: add hw trigger and buffer support

Jonathan Cameron jic23 at kernel.org
Tue Jun 20 09:55:15 PDT 2017


On Thu, 15 Jun 2017 16:24:57 +0300
Eugen Hristev <eugen.hristev at microchip.com> wrote:

> Added support for the external hardware trigger on pin ADTRG,
> integrated the three possible edges into the driver
> and created buffer management for data retrieval
> 
> Signed-off-by: Eugen Hristev <eugen.hristev at microchip.com>
> Acked-by: Ludovic Desroches <ludovic.desroches at microchip.com>
Applied to the togreg branch of iio.git and pushed out as
testing for the autobuilders to play with it.

Thanks,

Jonathan
> ---
>   Changes in v5:
>  - Moved DRDY ack in tryreenable function
>  - Used PTR_ERR to pass error code to probe
> 
>   Changes in v4:
>  - Used iio claim direct to make sure buffer is not enabled when someone might
>    try to use a software triggered conversion
> 
>   Changes in v3:
>  - No longer have all three possible triggers registered in the subsystem and
>    available in the sysfs. Only registering one trigger, and the possible edge
>    is being read from the device tree. In the device tree, any possible edge
>    can be set. There are three already made nodes for each possible edge which
>    can be selected.
>  - Fixed a bug where software triggered conversion could be started even if
>    the hardware trigger was enabled.
>  - Preallocate enough space for the buffer, considering all the channels
>    and timestamp
> 
>   Changes in v2:
>  - Moved buffer allocation and freeing into the preenable and postdisable
>    callbacks.
>    We have a total of scan bytes that can vary a lot depending on each channel
>    enabled at a certain point.
>  - made the at91 trigger list part of state structure
>  - made the iio trigger list preallocated in state structure
>  - moved irq enabling/disabling into the try_reenable callback
>  - on trigger disable must write disable registries as well
> 
>  drivers/iio/adc/at91-sama5d2_adc.c | 237 ++++++++++++++++++++++++++++++++++++-
>  1 file changed, 232 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c
> index e10dca3..1773a5d 100644
> --- a/drivers/iio/adc/at91-sama5d2_adc.c
> +++ b/drivers/iio/adc/at91-sama5d2_adc.c
> @@ -25,6 +25,10 @@
>  #include <linux/wait.h>
>  #include <linux/iio/iio.h>
>  #include <linux/iio/sysfs.h>
> +#include <linux/iio/buffer.h>
> +#include <linux/iio/trigger.h>
> +#include <linux/iio/trigger_consumer.h>
> +#include <linux/iio/triggered_buffer.h>
>  #include <linux/regulator/consumer.h>
>  
>  /* Control Register */
> @@ -132,6 +136,17 @@
>  #define AT91_SAMA5D2_PRESSR	0xbc
>  /* Trigger Register */
>  #define AT91_SAMA5D2_TRGR	0xc0
> +/* Mask for TRGMOD field of TRGR register */
> +#define AT91_SAMA5D2_TRGR_TRGMOD_MASK GENMASK(2, 0)
> +/* No trigger, only software trigger can start conversions */
> +#define AT91_SAMA5D2_TRGR_TRGMOD_NO_TRIGGER 0
> +/* Trigger Mode external trigger rising edge */
> +#define AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_RISE 1
> +/* Trigger Mode external trigger falling edge */
> +#define AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_FALL 2
> +/* Trigger Mode external trigger any edge */
> +#define AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_ANY 3
> +
>  /* Correction Select Register */
>  #define AT91_SAMA5D2_COSR	0xd0
>  /* Correction Value Register */
> @@ -145,14 +160,29 @@
>  /* Version Register */
>  #define AT91_SAMA5D2_VERSION	0xfc
>  
> +#define AT91_SAMA5D2_HW_TRIG_CNT 3
> +#define AT91_SAMA5D2_SINGLE_CHAN_CNT 12
> +#define AT91_SAMA5D2_DIFF_CHAN_CNT 6
> +
> +/*
> + * Maximum number of bytes to hold conversion from all channels
> + * plus the timestamp
> + */
> +#define AT91_BUFFER_MAX_BYTES ((AT91_SAMA5D2_SINGLE_CHAN_CNT +		\
> +				AT91_SAMA5D2_DIFF_CHAN_CNT) * 2 + 8)
> +
> +#define AT91_BUFFER_MAX_HWORDS (AT91_BUFFER_MAX_BYTES / 2)
> +
>  #define AT91_SAMA5D2_CHAN_SINGLE(num, addr)				\
>  	{								\
>  		.type = IIO_VOLTAGE,					\
>  		.channel = num,						\
>  		.address = addr,					\
> +		.scan_index = num,					\
>  		.scan_type = {						\
>  			.sign = 'u',					\
>  			.realbits = 12,					\
> +			.storagebits = 16,				\
>  		},							\
>  		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
>  		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
> @@ -168,9 +198,11 @@
>  		.channel = num,						\
>  		.channel2 = num2,					\
>  		.address = addr,					\
> +		.scan_index = num + AT91_SAMA5D2_SINGLE_CHAN_CNT,	\
>  		.scan_type = {						\
>  			.sign = 's',					\
>  			.realbits = 12,					\
> +			.storagebits = 16,				\
>  		},							\
>  		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
>  		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
> @@ -188,6 +220,12 @@ struct at91_adc_soc_info {
>  	unsigned			max_sample_rate;
>  };
>  
> +struct at91_adc_trigger {
> +	char				*name;
> +	unsigned int			trgmod_value;
> +	unsigned int			edge_type;
> +};
> +
>  struct at91_adc_state {
>  	void __iomem			*base;
>  	int				irq;
> @@ -195,11 +233,14 @@ struct at91_adc_state {
>  	struct regulator		*reg;
>  	struct regulator		*vref;
>  	int				vref_uv;
> +	struct iio_trigger		*trig;
> +	const struct at91_adc_trigger	*selected_trig;
>  	const struct iio_chan_spec	*chan;
>  	bool				conversion_done;
>  	u32				conversion_value;
>  	struct at91_adc_soc_info	soc_info;
>  	wait_queue_head_t		wq_data_available;
> +	u16				buffer[AT91_BUFFER_MAX_HWORDS];
>  	/*
>  	 * lock to prevent concurrent 'single conversion' requests through
>  	 * sysfs.
> @@ -207,6 +248,24 @@ struct at91_adc_state {
>  	struct mutex			lock;
>  };
>  
> +static const struct at91_adc_trigger at91_adc_trigger_list[] = {
> +	{
> +		.name = "external_rising",
> +		.trgmod_value = AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_RISE,
> +		.edge_type = IRQ_TYPE_EDGE_RISING,
> +	},
> +	{
> +		.name = "external_falling",
> +		.trgmod_value = AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_FALL,
> +		.edge_type = IRQ_TYPE_EDGE_FALLING,
> +	},
> +	{
> +		.name = "external_any",
> +		.trgmod_value = AT91_SAMA5D2_TRGR_TRGMOD_EXT_TRIG_ANY,
> +		.edge_type = IRQ_TYPE_EDGE_BOTH,
> +	},
> +};
> +
>  static const struct iio_chan_spec at91_adc_channels[] = {
>  	AT91_SAMA5D2_CHAN_SINGLE(0, 0x50),
>  	AT91_SAMA5D2_CHAN_SINGLE(1, 0x54),
> @@ -226,8 +285,128 @@ static const struct iio_chan_spec at91_adc_channels[] = {
>  	AT91_SAMA5D2_CHAN_DIFF(6, 7, 0x68),
>  	AT91_SAMA5D2_CHAN_DIFF(8, 9, 0x70),
>  	AT91_SAMA5D2_CHAN_DIFF(10, 11, 0x78),
> +	IIO_CHAN_SOFT_TIMESTAMP(AT91_SAMA5D2_SINGLE_CHAN_CNT
> +				+ AT91_SAMA5D2_DIFF_CHAN_CNT + 1),
> +};
> +
> +static int at91_adc_configure_trigger(struct iio_trigger *trig, bool state)
> +{
> +	struct iio_dev *indio = iio_trigger_get_drvdata(trig);
> +	struct at91_adc_state *st = iio_priv(indio);
> +	u32 status = at91_adc_readl(st, AT91_SAMA5D2_TRGR);
> +	u8 bit;
> +
> +	/* clear TRGMOD */
> +	status &= ~AT91_SAMA5D2_TRGR_TRGMOD_MASK;
> +
> +	if (state)
> +		status |= st->selected_trig->trgmod_value;
> +
> +	/* set/unset hw trigger */
> +	at91_adc_writel(st, AT91_SAMA5D2_TRGR, status);
> +
> +	for_each_set_bit(bit, indio->active_scan_mask, indio->num_channels) {
> +		struct iio_chan_spec const *chan = indio->channels + bit;
> +
> +		if (state) {
> +			at91_adc_writel(st, AT91_SAMA5D2_CHER,
> +					BIT(chan->channel));
> +			at91_adc_writel(st, AT91_SAMA5D2_IER,
> +					BIT(chan->channel));
> +		} else {
> +			at91_adc_writel(st, AT91_SAMA5D2_IDR,
> +					BIT(chan->channel));
> +			at91_adc_writel(st, AT91_SAMA5D2_CHDR,
> +					BIT(chan->channel));
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static int at91_adc_reenable_trigger(struct iio_trigger *trig)
> +{
> +	struct iio_dev *indio = iio_trigger_get_drvdata(trig);
> +	struct at91_adc_state *st = iio_priv(indio);
> +
> +	enable_irq(st->irq);
> +
> +	/* Needed to ACK the DRDY interruption */
> +	at91_adc_readl(st, AT91_SAMA5D2_LCDR);
> +	return 0;
> +}
> +
> +static const struct iio_trigger_ops at91_adc_trigger_ops = {
> +	.owner = THIS_MODULE,
> +	.set_trigger_state = &at91_adc_configure_trigger,
> +	.try_reenable = &at91_adc_reenable_trigger,
>  };
>  
> +static struct iio_trigger *at91_adc_allocate_trigger(struct iio_dev *indio,
> +						     char *trigger_name)
> +{
> +	struct iio_trigger *trig;
> +	int ret;
> +
> +	trig = devm_iio_trigger_alloc(&indio->dev, "%s-dev%d-%s", indio->name,
> +				      indio->id, trigger_name);
> +	if (!trig)
> +		return NULL;
> +
> +	trig->dev.parent = indio->dev.parent;
> +	iio_trigger_set_drvdata(trig, indio);
> +	trig->ops = &at91_adc_trigger_ops;
> +
> +	ret = devm_iio_trigger_register(&indio->dev, trig);
> +	if (ret)
> +		return ERR_PTR(ret);
> +
> +	return trig;
> +}
> +
> +static int at91_adc_trigger_init(struct iio_dev *indio)
> +{
> +	struct at91_adc_state *st = iio_priv(indio);
> +
> +	st->trig = at91_adc_allocate_trigger(indio, st->selected_trig->name);
> +	if (IS_ERR(st->trig)) {
> +		dev_err(&indio->dev,
> +			"could not allocate trigger\n");
> +		return PTR_ERR(st->trig);
> +	}
> +
> +	return 0;
> +}
> +
> +static irqreturn_t at91_adc_trigger_handler(int irq, void *p)
> +{
> +	struct iio_poll_func *pf = p;
> +	struct iio_dev *indio = pf->indio_dev;
> +	struct at91_adc_state *st = iio_priv(indio);
> +	int i = 0;
> +	u8 bit;
> +
> +	for_each_set_bit(bit, indio->active_scan_mask, indio->num_channels) {
> +		struct iio_chan_spec const *chan = indio->channels + bit;
> +
> +		st->buffer[i] = at91_adc_readl(st, chan->address);
> +		i++;
> +	}
> +
> +	iio_push_to_buffers_with_timestamp(indio, st->buffer, pf->timestamp);
> +
> +	iio_trigger_notify_done(indio->trig);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int at91_adc_buffer_init(struct iio_dev *indio)
> +{
> +	return devm_iio_triggered_buffer_setup(&indio->dev, indio,
> +			&iio_pollfunc_store_time,
> +			&at91_adc_trigger_handler, NULL);
> +}
> +
>  static unsigned at91_adc_startup_time(unsigned startup_time_min,
>  				      unsigned adc_clk_khz)
>  {
> @@ -293,14 +472,18 @@ static irqreturn_t at91_adc_interrupt(int irq, void *private)
>  	u32 status = at91_adc_readl(st, AT91_SAMA5D2_ISR);
>  	u32 imr = at91_adc_readl(st, AT91_SAMA5D2_IMR);
>  
> -	if (status & imr) {
> +	if (!(status & imr))
> +		return IRQ_NONE;
> +
> +	if (iio_buffer_enabled(indio)) {
> +		disable_irq_nosync(irq);
> +		iio_trigger_poll(indio->trig);
> +	} else {
>  		st->conversion_value = at91_adc_readl(st, st->chan->address);
>  		st->conversion_done = true;
>  		wake_up_interruptible(&st->wq_data_available);
> -		return IRQ_HANDLED;
>  	}
> -
> -	return IRQ_NONE;
> +	return IRQ_HANDLED;
>  }
>  
>  static int at91_adc_read_raw(struct iio_dev *indio_dev,
> @@ -313,6 +496,11 @@ static int at91_adc_read_raw(struct iio_dev *indio_dev,
>  
>  	switch (mask) {
>  	case IIO_CHAN_INFO_RAW:
> +		/* we cannot use software trigger if hw trigger enabled */
> +		ret = iio_device_claim_direct_mode(indio_dev);
> +		if (ret)
> +			return ret;
> +
>  		mutex_lock(&st->lock);
>  
>  		st->chan = chan;
> @@ -344,6 +532,8 @@ static int at91_adc_read_raw(struct iio_dev *indio_dev,
>  		at91_adc_writel(st, AT91_SAMA5D2_CHDR, BIT(chan->channel));
>  
>  		mutex_unlock(&st->lock);
> +
> +		iio_device_release_direct_mode(indio_dev);
>  		return ret;
>  
>  	case IIO_CHAN_INFO_SCALE:
> @@ -391,7 +581,8 @@ static int at91_adc_probe(struct platform_device *pdev)
>  	struct iio_dev *indio_dev;
>  	struct at91_adc_state *st;
>  	struct resource	*res;
> -	int ret;
> +	int ret, i;
> +	u32 edge_type;
>  
>  	indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*st));
>  	if (!indio_dev)
> @@ -432,6 +623,27 @@ static int at91_adc_probe(struct platform_device *pdev)
>  		return ret;
>  	}
>  
> +	ret = of_property_read_u32(pdev->dev.of_node,
> +				   "atmel,trigger-edge-type", &edge_type);
> +	if (ret) {
> +		dev_err(&pdev->dev,
> +			"invalid or missing value for atmel,trigger-edge-type\n");
> +		return ret;
> +	}
> +
> +	st->selected_trig = NULL;
> +
> +	for (i = 0; i < AT91_SAMA5D2_HW_TRIG_CNT; i++)
> +		if (at91_adc_trigger_list[i].edge_type == edge_type) {
> +			st->selected_trig = &at91_adc_trigger_list[i];
> +			break;
> +		}
> +
> +	if (!st->selected_trig) {
> +		dev_err(&pdev->dev, "invalid external trigger edge value\n");
> +		return -EINVAL;
> +	}
> +
>  	init_waitqueue_head(&st->wq_data_available);
>  	mutex_init(&st->lock);
>  
> @@ -499,10 +711,25 @@ static int at91_adc_probe(struct platform_device *pdev)
>  
>  	platform_set_drvdata(pdev, indio_dev);
>  
> +	ret = at91_adc_buffer_init(indio_dev);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "couldn't initialize the buffer.\n");
> +		goto per_clk_disable_unprepare;
> +	}
> +
> +	ret = at91_adc_trigger_init(indio_dev);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "couldn't setup the triggers.\n");
> +		goto per_clk_disable_unprepare;
> +	}
> +
>  	ret = iio_device_register(indio_dev);
>  	if (ret < 0)
>  		goto per_clk_disable_unprepare;
>  
> +	dev_info(&pdev->dev, "setting up trigger as %s\n",
> +		 st->selected_trig->name);
> +
>  	dev_info(&pdev->dev, "version: %x\n",
>  		 readl_relaxed(st->base + AT91_SAMA5D2_VERSION));
>  




More information about the linux-arm-kernel mailing list