[PATCH v6 00/11] Broadcom Stingray SOC Initial Support

[Florian Fainelli]

On 06/06/2017 03:30 PM, Stephen Boyd wrote:
> On 06/05, Florian Fainelli wrote:
>>
>>
>> On 06/05/2017 09:51 AM, Florian Fainelli wrote:
>>> On 06/01/2017 11:34 PM, Anup Patel wrote:
>>>> This patchset adds initial support of Broadcom Stingray SOC
>>>> by reusing existing Broadcom iProc device drivers.
>>>>
>>>> Most of the patches in this patchset are DT patches except
>>>> the Stingray clock tree support which just one patch.
>>>>
>>>> This patchset is based on Linux-4.12-rc3 and it is also available
>>>> at stingray-v6 branch of https://github.com/Broadcom/arm64-linux.git
>>>>
>>>> Changes since v5:
>>>>  - Rebased patches for Linux-4.12-rc3
>>>>  - Update DT node names to match register offset
>>>>
>>>> Changes since v4:
>>>>  - Reduce number of include headers in Stingray clk driver
>>>>
>>>> Changes since v3:
>>>>  - Rebased patches for Linux-4.12-rc1
>>>>  - Updated PATCH3 to have all clocks except genpll3 to be
>>>>    registered via platform driver probe
>>>>
>>>> Changes since v2:
>>>>  - Remove default bootargs from chosen DT node
>>>>  - Remove "linux" prefix from stdout DT attribute of chosen DT node
>>>>  - Remove use of GIC_CPU_MASK_xxx() for PPIs
>>>>
>>>> Changes since v1:
>>>>  - Rebased patches for Linux-4.12-rc1
>>>>  - Removed unwanted /memreserve/ from bcm958742-base.dtsi
>>>>  - Use ranges DT property to clear view of memory-layout
>>>>  - Make bcm-sr.h part of clock DT bindings patch
>>>>
>>>> Anup Patel (3):
>>>>   dt-bindings: bcm: Add Broadcom Stingray bindings document
>>>>   arm64: dts: Initial DTS files for Broadcom Stingray SOC
>>>>   arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray
>>>>
>>>> Oza Pawandeep (1):
>>>>   arm64: dts: Add I2C DT nodes for Stingray SoC
>>>>
>>>> Pramod Kumar (3):
>>>>   arm64: dts: Add NAND DT nodes for Stingray SOC
>>>>   arm64: dts: Add pinctrl DT nodes for Stingray SOC
>>>>   arm64: dts: Add GPIO DT nodes for Stingray SOC
>>>>
>>>> Sandeep Tripathy (3):
>>>>   dt-bindings: clk: Extend binding doc for Stingray SOC
>>>>   clk: bcm: Add clocks for Stingray SOC
>>>>   arm64: dts: Add clock DT nodes for Stingray SOC
>>>>
>>>> Srinath Mannam (1):
>>>>   arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC
>>>
>>> Applied patches 1, 4-11 to devicetree-arm64/next, thanks!
>>
>> Also took patch 2, to make sure everything builds properly, Stephen, let
>> me know if you want me to take patch #3 as well.
>>
> 
> Usually clk tree takes includes and hosts that in a stable branch
> for arm-soc maintainers to take. It seems that now arm-soc
> maintainers are asking that dts files use plain numbers and then
> switch to defines later after -rc1.
> 
> Should I go apply patch 2 myself so I can apply patch 3 to the
> clk tree? Personally, I think this is fine because git doesn't
> care about duplicate commits anyway and this is just #defines
> we're talking about. Alternatively, you can host patch 2 in a
> stable branch on v4.12-rc1 that I can pull into clk tree and then
> apply patch 3 on top of and merge up into clk-next. Or you can
> send me a PR for this clk driver and I can merge it into clk-next
> where patch 2 is the parent of the clk driver change.

Yes, please apply patch 2 and 3 in your tree, we should be fine. You
would also find patch 2 in a stable branch:

https://github.com/Broadcom/stblinux/refs/heads/arm64-stingray-for-4.13

Thanks!
-- 
Florian