[PATCH 1/6] ARM: dts: gose: add HDMI input

[Simon Horman]

From: Ulrich Hecht <ulrich.hecht+renesas at gmail.com>

Identical to the setup on Koelsch.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas at gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
---
 arch/arm/boot/dts/r8a7793-gose.dts | 68 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 66 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 95e51b79c1d7..30f083528468 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -253,12 +253,23 @@
 		};
 	};
 
+	hdmi-in {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&adv7612_in>;
+			};
+		};
+	};
+
 	hdmi-out {
 		compatible = "hdmi-connector";
 		type = "a";
 
 		port {
-			hdmi_con: endpoint {
+			hdmi_con_out: endpoint {
 				remote-endpoint = <&adv7511_out>;
 			};
 		};
@@ -395,6 +406,11 @@
 		groups = "audio_clk_a";
 		function = "audio_clk";
 	};
+
+	vin0_pins: vin0 {
+		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
+		function = "vin0";
+	};
 };
 
 &ether {
@@ -552,7 +568,34 @@
 			port at 1 {
 				reg = <1>;
 				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con>;
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+
+	hdmi-in at 4c {
+		compatible = "adi,adv7612";
+		reg = <0x4c>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		default-input = <0>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				adv7612_in: endpoint {
+					remote-endpoint = <&hdmi_con_in>;
+				};
+			};
+
+			port at 2 {
+				reg = <2>;
+				adv7612_out: endpoint {
+					remote-endpoint = <&vin0ep2>;
 				};
 			};
 		};
@@ -606,3 +649,24 @@
 &ssi1 {
 	shared-pin;
 };
+
+/* HDMI video input */
+&vin0 {
+	status = "okay";
+	pinctrl-0 = <&vin0_pins>;
+	pinctrl-names = "default";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vin0ep2: endpoint {
+			remote-endpoint = <&adv7612_out>;
+			bus-width = <24>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+			data-active = <1>;
+		};
+	};
+};
-- 
2.1.4