[RFC PATCH 2/3] remoteproc: imx_rproc: add a NXP/Freescale imx rproc driver
Suman Anna
s-anna at ti.com
Thu Jun 15 12:01:47 PDT 2017
Hi Oleksij,
On 06/14/2017 03:48 PM, Oleksij Rempel wrote:
> From: Oleksij Rempel <linux at rempel-privat.de>
>
> this driver was tested on NXP imx7d but should work on
> imx6sx as well.
> It will upload firmware to OCRAM, which shared memory between
> Cortex A7 and Cortex M4, then turn M4 on.
Mostly looks fine, need to address few comments. I take it that you
haven't added the binding since this is just an RFC.
>
> Signed-off-by: Oleksij Rempel <linux at rempel-privat.de>
> ---
> drivers/remoteproc/Kconfig | 8 ++
> drivers/remoteproc/Makefile | 1 +
> drivers/remoteproc/imx_rproc.c | 264 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/remoteproc/imx_rproc.c
>
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index faad69a1a597..8d33bff4f530 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -130,6 +130,14 @@ config ST_SLIM_REMOTEPROC
> tristate
> depends on REMOTEPROC
>
> +config IMX_REMOTEPROC
> + tristate "IMX6/7 remoteproc support"
> + depends on SOC_IMX6SX || SOC_IMX7D
> + depends on REMOTEPROC
> + help
> + TODO, write some thing here
> + This can be either built-in or a loadable module.
> +
> endif # REMOTEPROC
>
> endmenu
> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
> index ffc5e430df27..d351c25cdb4e 100644
> --- a/drivers/remoteproc/Makefile
> +++ b/drivers/remoteproc/Makefile
> @@ -19,3 +19,4 @@ qcom_wcnss_pil-y += qcom_wcnss.o
> qcom_wcnss_pil-y += qcom_wcnss_iris.o
> obj-$(CONFIG_ST_REMOTEPROC) += st_remoteproc.o
> obj-$(CONFIG_ST_SLIM_REMOTEPROC) += st_slim_rproc.o
> +obj-$(CONFIG_IMX_REMOTEPROC) += imx_rproc.o
> diff --git a/drivers/remoteproc/imx_rproc.c b/drivers/remoteproc/imx_rproc.c
> new file mode 100644
> index 000000000000..6bef85237a27
> --- /dev/null
> +++ b/drivers/remoteproc/imx_rproc.c
> @@ -0,0 +1,264 @@
> +/*
> + * Oleksij Rempel <o.rempel at pengutronix.de>
Please add a blank line here.
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/remoteproc.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +
> +#define IMX7D_ENABLE_M4 BIT(3)
> +#define IMX7D_SW_M4P_RST BIT(2)
> +#define IMX7D_SW_M4C_RST BIT(1)
> +#define IMX7D_SW_M4C_NON_SCLR_RST BIT(0)
> +
> +#define IMX7D_M4_RST_MASK 0xf
> +
> +
> +#define IMX7D_RPROC_MEM_MAX 2
> +enum {
> + IMX7D_RPROC_IMEM,
> + IMX7D_RPROC_DMEM,
> +};
> +
> +static const char *mem_names[IMX7D_RPROC_MEM_MAX] = {
> + [IMX7D_RPROC_IMEM] = "imem",
> + [IMX7D_RPROC_DMEM] = "dmem",
> +};
Do you really need these to be globally defined? You only need them in
the addr_init function, they can be made local to that function.
> +
> +/**
> + * struct imx_rproc_mem - slim internal memory structure
> + * @cpu_addr: MPU virtual address of the memory region
> + * @bus_addr: Bus address used to access the memory region
> + * @size: Size of the memory region
> + */
> +struct imx_rproc_mem {
> + void __iomem *cpu_addr;
> + phys_addr_t bus_addr;
Are the rproc-view of these regions same as the bus addresses or
do they have their own local addresses? If latter, images that are built
for those will be using those addresses in which case you need some
offset calculation in the da_to_va ops?
> + size_t size;
> +};
> +
> +struct imx_rproc_dcfg {
> + int offset;
> +};
> +
> +struct imx_rproc {
> + struct device *dev;
> + struct regmap *regmap;
> + struct rproc *rproc;
> + const struct imx_rproc_dcfg *dcfg;
No need of aligning the variables, you can get rid of the additional
whitespaces and maintain consistent style.
> + struct imx_rproc_mem mem[IMX7D_RPROC_MEM_MAX];
> + struct clk *clk;
> +};
> +
> +static const struct imx_rproc_dcfg imx_rproc_cfg_imx7d = {
> + .offset = 0xc,
> +};
> +
> +static int imx_rproc_start(struct rproc *rproc)
> +{
> + struct imx_rproc *priv = rproc->priv;
> + const struct imx_rproc_dcfg *dcfg = priv->dcfg;
> + struct device *dev = priv->dev;
> + int ret;
> +
> + ret = clk_enable(priv->clk);
> + if (ret) {
> + dev_err(&rproc->dev, "Failed to enable clock\n");
> + return ret;
> + }
> +
> + ret = regmap_update_bits(priv->regmap, dcfg->offset,
> + IMX7D_M4_RST_MASK,
> + IMX7D_SW_M4C_RST | IMX7D_SW_M4P_RST | IMX7D_ENABLE_M4);
> + if (ret) {
> + dev_err(dev, "Filed to enable M4!\n");
> + clk_disable(priv->clk);
> + }
> +
> + return ret;
> +}
> +
> +static int imx_rproc_stop(struct rproc *rproc)
> +{
> + struct imx_rproc *priv = rproc->priv;
> + const struct imx_rproc_dcfg *dcfg = priv->dcfg;
> + struct device *dev = priv->dev;
> + int ret;
> +
> + ret = regmap_update_bits(priv->regmap, dcfg->offset,
> + IMX7D_M4_RST_MASK,
> + IMX7D_SW_M4C_NON_SCLR_RST);
> + if (ret)
> + dev_err(dev, "Filed to stop M4!\n");
> +
> + clk_disable(priv->clk);
> +
> + return ret;
> +}
> +
> +static void *imx_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
> +{
> + struct imx_rproc *priv = rproc->priv;
> + void *va = NULL;
> + int i;
> +
> + for (i = 0; i < IMX7D_RPROC_MEM_MAX; i++) {
> + if (da != priv->mem[i].bus_addr)
> + continue;
> +
> + if (len <= priv->mem[i].size) {
> + /* __force to make sparse happy with type conversion */
> + va = (__force void *)priv->mem[i].cpu_addr;
> + break;
> + }
> + }
> +
> + dev_dbg(&rproc->dev, "da = 0x%llx len = 0x%x va = 0x%p\n", da, len, va);
> +
> + return va;
> +}
> +
> +static const struct rproc_ops imx_rproc_ops = {
> + .start = imx_rproc_start,
> + .stop = imx_rproc_stop,
> + .da_to_va = imx_rproc_da_to_va,
> +};
> +
> +static const struct of_device_id imx_rproc_of_match[] = {
> + { .compatible = "fsl,imx7d-rproc", .data = &imx_rproc_cfg_imx7d },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, imx_rproc_of_match);
> +
> +static int imx_rproc_addr_init(struct imx_rproc *priv,
> + struct platform_device *pdev)
> +{
> + int i, err;
> + struct resource *res;
> +
> + /* get imem and dmem */
> + for (i = 0; i < ARRAY_SIZE(mem_names); i++) {
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> + mem_names[i]);
> + if (!res)
> + continue;
> +
> + priv->mem[i].cpu_addr = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->mem[i].cpu_addr)) {
> + dev_err(&pdev->dev, "devm_ioremap_resource failed\n");
> + err = PTR_ERR(priv->mem[i].cpu_addr);
> + return err;
> + }
> + priv->mem[i].bus_addr = res->start & 0xffff;
> + priv->mem[i].size = resource_size(res);
> + }
> +
> + return 0;
> +}
> +
> +static int imx_rproc_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + struct imx_rproc *priv;
> + struct rproc *rproc;
> + struct regmap_config config = { .name = "imx_rproc" };
> + const struct imx_rproc_dcfg *dcfg;
> + struct regmap *regmap;
> + int ret;
> +
> + regmap = syscon_regmap_lookup_by_phandle(np, "syscon");
> + if (IS_ERR(regmap)) {
> + dev_err(dev, "failed to find syscon\n");
> + return PTR_ERR(regmap);
> + }
> + regmap_attach_dev(dev, regmap, &config);
> +
> + /* set some other name then imx */
> + rproc = rproc_alloc(dev, "imx_rproc", &imx_rproc_ops, NULL, sizeof(*priv));
> + if (!rproc) {
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + dcfg = of_device_get_match_data(dev);
> + if (!dcfg)
> + return -EINVAL;
move this up to the beginning of the function. You can avoid the cleanup
(you are missing an rproc_free() here)
> +
> + priv = rproc->priv;
> + priv->rproc = rproc;
> + priv->regmap = regmap;
> + priv->dcfg = dcfg;
> +
> + dev_set_drvdata(dev, rproc);
> +
> + ret = imx_rproc_addr_init(priv, pdev);
> + if (ret) {
> + dev_err(dev, "filed on imx_rproc_addr_init\n");
> + goto err_put_rproc;
> + }
> +
> + priv->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(priv->clk)) {
> + dev_err(dev, "Failed to get clock\n");
> + return PTR_ERR(priv->clk);
> + }
> +
> + ret = rproc_add(rproc);
> + if (ret) {
> + dev_err(dev, "rproc_add failed\n");
> + goto err_put_rproc;
> + }
> +
> + ret = clk_prepare(priv->clk);
> + if (ret)
> + dev_err(dev, "failed to get clock\n");
How are your internal memories clocked? If they need the same clock,
rproc_add() would need the clock to be enabled for loading section data
into those regions as part of rproc_boot(), and your current enable in
imx_rproc_start() will be too late. Also, do not see a balancing
clk_unprepare() call in remove, and a missing rproc_del() on failure here.
regards
Suman
> +
> + return ret;
> +
> +err_put_rproc:
> + rproc_free(rproc);
> +err:
> + return ret;
> +}
> +
> +static int imx_rproc_remove(struct platform_device *pdev)
> +{
> + struct rproc *rproc = platform_get_drvdata(pdev);
> +
> + rproc_del(rproc);
> + rproc_free(rproc);
> +
> + return 0;
> +}
> +
> +static struct platform_driver imx_rproc_driver = {
> + .probe = imx_rproc_probe,
> + .remove = imx_rproc_remove,
> + .driver = {
> + .name = "imx_rproc",
> + .of_match_table = imx_rproc_of_match,
> + },
> +};
> +
> +module_platform_driver(imx_rproc_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("IMX6/7 remote processor control driver");
> +MODULE_AUTHOR("Oleksij Rempel <o.rempel at pengutronix.de>");
>
More information about the linux-arm-kernel
mailing list