[PATCH v3 1/9] ARM: dts: imx6ul-isiot: Add Sound card with codec node

[Shawn Guo]

On Thu, Jun 15, 2017 at 10:21:43AM +0530, Jagan Teki wrote:
> On Thu, Jun 15, 2017 at 7:50 AM, Shawn Guo <shawnguo at kernel.org> wrote:
> > On Wed, Jun 14, 2017 at 08:17:04PM +0530, Jagan Teki wrote:
> >> On Fri, Apr 7, 2017 at 6:46 PM, Shawn Guo <shawnguo at kernel.org> wrote:
> >> > On Thu, Apr 06, 2017 at 11:32:07PM +0530, Jagan Teki wrote:
> >> >> From: Jagan Teki <jagan at amarulasolutions.com>
> >> >>
> >> >> Add support for Sound card and related codec(via i2c1) nodes
> >> >> on Engicam Is.IoT MX6UL variant module boards.
> >> >>
> >> >> Cc: Shawn Guo <shawnguo at kernel.org>
> >> >> Cc: Matteo Lisi <matteo.lisi at engicam.com>
> >> >> Cc: Michael Trimarchi <michael at amarulasolutions.com>
> >> >> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> >> >> ---
> >> >> Changes for v3:
> >> >> - Replace fsl,imx-audio-sgtl5000 and use simple-audio-card
> >> >> Changes for v2:
> >> >> - Use proper [label:] node-name[@unit-address] for codec
> >> >> - Remove incorrect codec property 'wlf,shared-lrclk'
> >> >> - Remove 'gpr' from sound card node
> >> >>
> >> >>  arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 10 +++++++
> >> >>  arch/arm/boot/dts/imx6ul-isiot.dtsi        | 44 ++++++++++++++++++++++++++++++
> >> >
> >> > Can you help me understand how these two files are related?  Why is
> >> > sgtl5000 added into one and sound node added into the other?
> >>
> >> lcdif, ts and sound card which may differ based on the base-board
> >> connected with SOM, So I moved these stuff which are related to
> >> Starter kit supported once's and used with SOM dts files. if some
> >> other board with same SOM can have different lcdif and etc so they can
> >> define locally to dts.
> >
> > I do not follow how these stuff are organized.  So far we have the
> > following isiot dts files.
> >
> >  - imx6ul-isiot-common.dtsi
> >  - imx6ul-isiot.dtsi
> >  - imx6ul-isiot-emmc.dts and imx6ul-isiot-nand.dts
> >
> > How are they mapping to SoM and base-board?
> 
> isiot is a modules class, with that emmc and nand are two separate
> SOM's. the current support is for mounting these SOM's on Development
> base board[1]. So, for isiot module class we have imx6ul-isiot.dtsi
> and emmc and nand SOM's have imx6ul-isiot-emmc.dts and
> imx6ul-isiot-nand.dts. There are some Carrier boards[1] which were
> used with different lcdif and other changes, So
> imx6ul-isiot-common.dtsi have changes common across emmc and nand,
> instead of adding them into individual dts files I moved in
> -common.dtsi.  So in future if isiot SOM mounted on carrier board
> which should have a separate dts and which may or may not use
> imx6ul-isiot-common.dtsi

So you are not sure if imx6ul-isiot-common.dtsi will be used by carrier
board.  Then what's the point to have it now?

You are saying imx6ul-isiot-common.dtsi is created to accommodate the
common things across emmc and nand SoMs, but it actually contains LCD
and Touch such base-board level of stuff.  Confusing.

I feel the abstraction is wrong from the beginning.  Ideally, we should
have something like below.

 - imx6ul-isiot.dtsi
 - imx6ul-isiot-kit.dts and imx6ul-isiot-carrier.dts

The -isiot should have everything on SoM and common stuff between -kit
and -carrier boards, while -kit and -carrier include -isiot and contains
the base-board specific things.  The -isiot can have both emmc and nand
devices with "disabled" status, and let firmware turn device on per SoM
it boots.  In that case, the abstraction level can be less and clearer.

Thoughts?

Shawn