[PATCH v8 6/9] drivers: perf: hisi: Add support for Hisilicon Djtag driver

[Will Deacon]

On Fri, Jun 09, 2017 at 04:10:12PM +0100, John Garry wrote:
> On 09/06/2017 15:30, Will Deacon wrote:
> >On Fri, Jun 09, 2017 at 03:18:39PM +0100, John Garry wrote:
> >>On 08/06/2017 17:35, Mark Rutland wrote:
> >>>Hi,
> >>>
> >>>On Mon, May 22, 2017 at 08:48:32PM +0800, Shaokun Zhang wrote:
> >>>>+/*
> >>>>+ * hisi_djtag_lock_v2: djtag lock to avoid djtag access conflict b/w kernel
> >>>>+ * and UEFI.
> >>>
> >>>The mention of UEFI here worries me somewhat, and I have a number of
> >>>questions specifically relating to how we interact with UEFI here.
> >>>
> >>
> >>Hi Mark,
> >>
> >>This djtag locking mechanism is an advisory software-only policy. The
> >>problem is the hardware designers made an interface which does not consider
> >>multiple agents in the system concurrently accessing the djtag registers.
> >>
> >>System wide, djtag is used as an interface to other HW modules, but we only
> >>use for perf HW in the kernel.
> >>
> >>>When precisely does UEFI need to touch the djtag hardware? e.g. does
> >>>this happen in runtime services? ... or completely asynchronously?
> >>>
> >>
> >>Actually it's trusted firmware which accesses for L3 cache management in CPU
> >>hotplug
> >>
> >>>What does UEFI do with djtag when it holds the lock?
> >>>
> >>
> >>As mentioned, cache management
> >>
> >>>Are there other software agents (e.g. secure firmware) which try to
> >>>take this lock?
> >>>
> >>
> >>No
> >>
> >>>Can you explain how the locking scheme works? e.g. is this an advisory
> >>>software-only policy, or does the hardware prohibit accesses from other
> >>>agents somehow?
> >>>
> >>
> >>The locking scheme is a software solution to spinlock. It's uses djtag
> >>module select register as the spinlock flag, to avoid using some shared
> >>memory.
> >>
> >>The tricky part is that there is no test-and-set hardware support, so we use
> >>this algorithm:
> >>- precondition: flag initially set unlocked
> >>
> >>a. agent reads flag
> >>    - if not unlocked, continues to poll
> >>    - otherwise, writes agent's unique lock value to flag
> >>b. agent waits defined amount of time *uninterrupted* and then checks the
> >>flag
> >
> >How do you figure out this time period? Doesn't it need to be no shorter
> >than the longest critical section?
> >
> 
> Hi Will,
> 
> As you know, we need to delay to guard against contenting set-and-check. And
> the ratio in delay duration would be 2:1 for agents to guard against race of
> the contended set-and-check.
> 
> As for the specific time, we were working the basis that a delay of 10us
> would be more than adequate time for the set-and-check to complete.
> 
> Sorry, but I didn't get critical section question. Are you questioning the
> possiblity of one agent getting the lock, doing it's djtag operation, and
> releasing, all while other agent is waiting on it's own set-and-check?

Apologies, I misunderstood your algorithm (I thought step (a) was on one CPU
and step (b) was on another). Still, I don't understand the need for the
timeout. If you instead read back the flag immediately, wouldn't it still
work? e.g.


lock:
  Readl_relaxed flag
  if (locked)
    goto lock;

  Writel_relaxed unique ID to flag
  Readl flag
  if (locked by somebody else)
    goto lock;

<critical section>

unlock:
  Writel unlocked value to flag


Given that we're dealing with iomem, I think it will work, but I could be
missing something obvious.

Thoughts?

Will