[[PATCH v2]] drivers: leds/trigger: system cannot enter suspend

[Jacek Anaszewski]

Hi Bruce,

On 06/08/2017 04:57 AM, Bruce Zhang wrote:
> Hi,
> 
> As suspend/resume procedure is as below:
> pm_notifier_call_chain(PM_SUSPEND_PREPARE)->device suspend -> syscore suspend -> enter suspend mode -> syscore resume -> device resume -> pm_notifier_call_chain(PM_POST_SUSPEND).
> If led brightness control depends on other device/hardware (such as I2C), the LED turn off action should be earlier than device suspend. pm_notifier may be a suitable method to turn off LED.

OK, so I agree that the most proper fix to the discussed problem
would be ignoring brightness setting requests after suspend, as Pavel
suggested.

led_classdev_suspend() already turns the LED off and
led_classdev_resume() brings the brightness back.

Also led_set_brightness_nosleep() and led_set_brightness_sync()
don't propagate brightness change to the driver if LED_SUSPENDED
is set.

There are two problems though:
1. __led_set_brightness() and __led_set_brightness_blocking() don't
   check the flag, and they can be called from set_brightness_delayed(),
   that was already queued at the time of setting LED_SUSPENDED flag.
2. LED_SUSPENDED flag is accessed in a non-atomic way.

The solution as I see it would be respectively:
1. Return from __led_set_brightness() and
   __led_set_brightness_blocking() if LED_SUSPENDED is set.
2. Switch to accessing struct led_classdev's flags with use of
   bitops. Fortunately those flags are mainly set prior LED class
   device registration and only LED_SYSFS_DISABLE, LED_SUSPENDED
   and LED_UNREGISTERING are accessed afterwards, and only in the LED
   core, so only those places would have to be modified.

Best regards,
Jacek Anaszewski

> -----Original Message-----
> From: Pavel Machek [mailto:pavel at ucw.cz] 
> Sent: Wednesday, June 07, 2017 6:31 PM
> To: Linus Walleij <linus.walleij at linaro.org>
> Cc: Bruce Zhang <bo.zhang at nxp.com>; Ulf Hansson <ulf.hansson at linaro.org>; linux-arm-kernel at lists.infradead.org; Jacek Anaszewski <jacek.anaszewski at gmail.com>; Richard Purdie <rpurdie at rpsys.net>; linux-leds at vger.kernel.org
> Subject: Re: [[PATCH v2]] drivers: leds/trigger: system cannot enter suspend
> 
> Hi!
> 
> On Wed 2017-06-07 11:46:10, Linus Walleij wrote:
>> On Wed, Jun 7, 2017 at 9:12 AM, Pavel Machek <pavel at ucw.cz> wrote:
>>
>>> Core reason is that 5ab92a7cb is wrong. (Very wrong; it papers over 
>>> the issue for one trigger, but we have more than one... Even if 
>>> special handling for heartbeat is warranted, that handling would be 
>>> "turn the led off" not "unregister the trigger", which is 
>>> userland-visible action.)
>>
>> OK yeah I guess you're right.
>>
>> I just couldn't think about anything better and didn't get any review 
>> at the time, so mistakes were made.
>>
>>> That one should be reverted, then maybe the driver should be fixed 
>>> to turn the led off during suspend.
>>
>> Do you mean that the heartbeat trigger driver should be fixed to turn 
>> off the LED during sleep?
>>
>> That is essentially what I was trying to achieve.
> 
> I don't think we should be fixing it at trigger level.
> 
> If userspace keeps blinking using "brightness" attribute, would we like the LED to be off during suspend? I think so.
> 
>> The reason it is done as it is, is that the trigger sets up a timer to 
>> do its job, and the timer may trigger between the point you turn off 
>> the LED and the system really goes to suspend, again maybe turning the 
>> LED on and again leaving the system with a glowing LED at suspend.
> 
>> The patch also solves the following phenomenon, sorry for not writing 
>> in the commit:
>>
>> - Turn off LED
>> - Suspend I2C hardware
>> - Timer trigger
>> - Trying to blink the LED using I2C
>> - Crap in the console about the failed I2C transaction
>> - Actual suspen happens
>> - System comes online
>> - Trying to blink the LED using I2C
>> - Crap in the console about the failed I2C transaction
>> - Resume I2C hardware
>>
>> It's just very fragile this trigger, turning off the LED from the PM 
>> notifier is obviously not enough, we also need to disable the timer, 
>> and then take it back online after resume.
> 
> No, leave the timer alone, and actually leave the trigger alone.
> 
> Simply make the driver turn the LED off in .suspend() callback, and then ignore further requests until .resume(). That will get rid of power drain _and_ "failed I2C transaction" messages, right?
> 
> (Actually, I tested with the heartbeat trigger, and it is not re-installed after resume. Another reason to revert the patch).
> 
> Thanks,
> 
> 									Pavel
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
>