[PATCH v2 01/11] dt-bindings: update the binding for Allwinner H3 TVE support

[Maxime Ripard]

On Mon, Jun 05, 2017 at 12:01:39AM +0800, Icenowy Zheng wrote:
> Allwinner H3 features a "DE2.0" and a TV Encoder.
> 
> Add device tree bindings for the following parts:
> - H3 TCONs
> - H3 Mixers
> - The connection between H3 TCONs and H3 Mixers
> - H3 TV Encoder
> - H3 Display engine
> 
> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
> ---
> Changes in v2:
> - Changed endpoint reg definition on TCONs and Mixers. Now the endpoint
>   id is just the component id.
> - Changed TVE and TCON1 binding -- now CLK_TVE is passed as TCON1 lcd-ch1.
> 
>  .../bindings/display/sunxi/sun4i-drm.txt           | 37 +++++++++++++++++++---
>  1 file changed, 33 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> index b83e6018041d..7ad164cb7dcb 100644
> --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -49,7 +49,9 @@ The TV Encoder supports the composite and VGA output. It is one end of
>  the pipeline.
>  
>  Required properties:
> - - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
> + - compatible: value must be either:
> +    * allwinner,sun4i-a10-tv-encoder
> +    * allwinner,sun8i-h3-tv-encoder
>   - reg: base address and size of memory-mapped region
>   - clocks: the clocks driving the TV encoder
>   - resets: phandle to the reset controller driving the encoder
> @@ -69,23 +71,27 @@ Required properties:
>     * allwinner,sun6i-a31-tcon
>     * allwinner,sun6i-a31s-tcon
>     * allwinner,sun8i-a33-tcon
> +   * allwinner,sun8i-h3-tcon
>     * allwinner,sun8i-v3s-tcon
>   - reg: base address and size of memory-mapped region
>   - interrupts: interrupt associated to this IP
>   - clocks: phandles to the clocks feeding the TCON. Three are needed:
>     - 'ahb': the interface clocks
> -   - 'tcon-ch0': The clock driving the TCON channel 0
>   - resets: phandles to the reset controllers driving the encoder
>     - "lcd": the reset line for the TCON channel 0
>  
>   - clock-names: the clock names mentioned above
>   - reset-names: the reset names mentioned above
> - - clock-output-names: Name of the pixel clock created
>  
>  - ports: A ports node with endpoint definitions as defined in
>    Documentation/devicetree/bindings/media/video-interfaces.txt. The
>    first port should be the input endpoint, the second one the output
>  
> +  In the situation of Display Engine 2.0 that the connection between
> +  the mixer and the TCON can be swapped, the input should have two
> +  endpoints. The first input endpoint should be connected to mixer0
> +  and the second should be connected to mixer1.
> +

AFAIK, this is also the case for dual-pipelines on DE1 (for example on
the A31). And this is already covered by:

"
For the input port of all components up to the TCON in the display
pipeline, if there are multiple components, the local endpoint IDs
must correspond to the index of the upstream block. For example, if
the remote endpoint is Frontend 1, then the local endpoint ID must
be 1.
"

>    The output may have multiple endpoints. The TCON has two channels,
>    usually with the first channel being used for the panels interfaces
>    (RGB, LVDS, etc.), and the second being used for the outputs that
> @@ -94,7 +100,23 @@ Required properties:
>    channel the endpoint is associated to. If that property is not
>    present, the endpoint number will be used as the channel number.
>  
> -On SoCs other than the A33 and V3s, there is one more clock required:
> +For the following compatibles:
> +   * allwinner,sun5i-a13-tcon
> +   * allwinner,sun6i-a31-tcon
> +   * allwinner,sun6i-a31s-tcon
> +   * allwinner,sun8i-a33-tcon
> +   * allwinner,sun8i-v3s-tcon
> +there is one more clock and one more property required:
> + - clocks:
> +   - 'tcon-ch0': The clock driving the TCON channel 0
> + - clock-output-names: Name of the pixel clock created
> +
> +For the following compatibles:
> +   * allwinner,sun5i-a13-tcon
> +   * allwinner,sun6i-a31-tcon
> +   * allwinner,sun6i-a31s-tcon
> +   * allwinner,sun8i-h3-tcon
> +there is one more clock required:
>     - 'tcon-ch1': The clock driving the TCON channel 1
>  
>  DRC
> @@ -189,6 +211,8 @@ supported.
>  Required properties:
>    - compatible: value must be one of:
>      * allwinner,sun8i-v3s-de2-mixer
> +    * allwinner,sun8i-h3-de2-mixer0
> +    * allwinner,sun8i-h3-de2-mixer1

Again, please explain why we need to have different compatibles
here. If it's only about the number of planes, this should be dealt
with a property, not a compatible.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170607/1cba8e0c/attachment.sig>