[PATCH 0/7] dra7: Fixes for MMC devicetree node
Kishon Vijay Abraham I
kishon at ti.com
Tue Jun 6 03:36:23 PDT 2017
Hi Tony,
On Tuesday 06 June 2017 09:47 AM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Friday 02 June 2017 04:20 PM, Ulf Hansson wrote:
>> On 1 June 2017 at 16:33, Kishon Vijay Abraham I <kishon at ti.com> wrote:
>>> There are the set of fixes that were sent initially as part
>>> of [1].
>>>
>>> These are mostly fixes w.r.t populating regulators in
>>> mmc dt node. It was working before because the regulators
>>> connecting to the IO lines are always on regulators. This will
>>> break once we add UHS support where voltage has to be changed
>>> dynamically.
>>>
>>> Performed enumeration testing on dra72-evm-revc, dra72-evm,
>>> dra7-evm, am572x-evm, am571x-idk and am572x-idk.
>>>
>>> This is a preparation series for adding UHS mode support in
>>> the above mentioned platforms.
>>>
>>> [1] -> https://lkml.org/lkml/2017/5/19/196
>>>
>>> Kishon Vijay Abraham I (5):
>>> ARM: dts: dra72-evm-common: Correct vmmc-supply for mmc2
>>> ARM: dts: dra72-evm: Add vmmc_aux supply to mmc1
>>> ARM: dts: dra72-evm-revc: Add vmmc_aux supply to mmc1
>>> ARM: dts: am57xx-beagle-x15-revb1: Fix supply name used for MMC1 IO
>>> lines
>>> ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
>>>
>>> Ravikumar Kattekola (1):
>>> ARM: dts: dra7-evm: Correct the vmmc-supply for mmc2
>>>
>>> Sekhar Nori (1):
>>> ARM: OMAP2+: Add pdata-quirks for MMC/SD on DRA74x EVM
>>>
>>> arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 2 +-
>>> arch/arm/boot/dts/dra7-evm.dts | 10 ++++++++-
>>> arch/arm/boot/dts/dra7.dtsi | 5 +++++
>>> arch/arm/boot/dts/dra71-evm.dts | 14 ++++++++++++
>>> arch/arm/boot/dts/dra72-evm-common.dtsi | 2 --
>>> arch/arm/boot/dts/dra72-evm-revc.dts | 18 ++++++++++++++++
>>> arch/arm/boot/dts/dra72-evm.dts | 18 ++++++++++++++++
>>> arch/arm/mach-omap2/pdata-quirks.c | 31 +++++++++++++++++++++++++++
>>> include/linux/platform_data/hsmmc-omap.h | 3 +++
>>> 9 files changed, 99 insertions(+), 4 deletions(-)
>>
>> This series add a bunch of new vmmc_aux regulators for the mmc
>> controller nodes. I would rather see that omap_hsmmc also converts to
>> use the generic mmc binding for this regulator, which is "vqmmc".
>>
>> To accomplish that, omap_hsmmc needs to convert to use
>> mmc_regulator_get_supply(). If the "vqmmc" regulator isn't found, it
>> should fallback to try the "vmmc_aux".
>>
>> Can you do that?
>
> sure, I'll prepare that change.
omap3-overo-base.dtsi has the following dt node for mmc.
/* optional on board WiFi */
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&w3cbw003c_npoweron>;
vqmmc-supply = <&w3cbw003c_bt_nreset>;
vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
bus-width = <4>;
cap-sdio-irq;
non-removable;
};
It has both "vqmmc-supply" and "vmmc_aux-supply". However omap-hsmmc driver has
never parsed vqmmc so far. So I'd assume bt was never functional and it's used
only for wifi.
So for the change suggested by Ulf, Can I do something like below, so that we
can keep wifi functional (ignoring bt since that was never functional)?
- vqmmc-supply = <&w3cbw003c_bt_nreset>;
- vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
+ vqmmc-supply = <&w3cbw003c_wifi_nreset>;
Thanks
Kishon
More information about the linux-arm-kernel
mailing list