[PATCH v3 5/6] dt-bindings: display: stm32: Add DSI host driver

[Neil Armstrong]

Hi Philippe,

On 06/02/2017 04:37 PM, Philippe CORNU wrote:
> This patch adds documentation of device tree bindings for the STM32
> DSI host driver based on the Synopsys DW MIPI DSI bridge driver.
> ---
>  .../devicetree/bindings/display/st,stm32-ltdc.txt  | 83 +++++++++++++++++++++-
>  1 file changed, 82 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt
> index 90a8459..4cd32bd 100644
> --- a/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt
> +++ b/Documentation/devicetree/bindings/display/st,stm32-ltdc.txt
> @@ -12,8 +12,39 @@
>    Required nodes:
>      - Video port for RGB output.
>  
> -Example:
> +* STMicroelectronics STM32 dsi specific extensions to Synopsys DesignWare MIPI
> +  DSI host controller

Why is "dsi" in low-case only here and below ?

>  
> +The STMicroelectronics STM32 dsi driver uses the Synopsys DesignWare MIPI
> +DSI host controller driver (related documentation in [5]).
> +
> +Required properties:
> +- #address-cells: Should be <1>.
> +- #size-cells: Should be <0>.
> +- compatible: "st,stm32-dsi".
> +- reg: Memory mapped base address and length of the DWC MIPI DSI registers.
> +- clocks: References to all the clocks specified in the clock-names property
> +  as specified in [1].
> +- clock-names:
> +  - peripheral clock string name, must be "pclk".
> +  - phy pll reference clock string name, must be "ref".
> +- resets: References to all the resets specified in the reset-names property
> +  as specified in [2].
> +- reset-names: string reset name, must be "apb".
> +
> +Required nodes:
> +- dsi input port node: connected to the ltdc rgb output port, see [3] & [4].
> +- panel or bridge node: see [6].
> +
> +Note: You can find more documentation
> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
> +[2] Documentation/devicetree/bindings/reset/reset.txt
> +[3] Documentation/devicetree/bindings/media/video-interfaces.txt
> +[4] Documentation/devicetree/bindings/graph.txt
> +[5] Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
> +[6] Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
> +
> +Example 1: RGB panel
>  / {
>  	...
>  	soc {
> @@ -33,3 +64,53 @@ Example:
>  		};
>  	};
>  };
> +
> +Example 2: DSI panel
> +
> +/ {
> +	...
> +	soc {
> +	...
> +		ltdc: display-controller at 40016800 {
> +			compatible = "st,stm32-ltdc";
> +			reg = <0x40016800 0x200>;
> +			interrupts = <88>, <89>;
> +			resets = <&rcc STM32F4_APB2_RESET(LTDC)>;
> +			clocks = <&rcc 1 CLK_LCD>;
> +			clock-names = "lcd";
> +
> +			port {
> +				ltdc_out_dsi: endpoint {
> +					remote-endpoint = <&dsi_in>;
> +				};
> +			};
> +		};
> +
> +
> +		dsi: dsi at 40016c00 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-dsi";
> +			reg = <0x40016c00 0x800>;
> +			clocks = <&rcc 1 CLK_F469_DSI>, <&clk_hse>;
> +			clock-names = "ref", "pclk";
> +			resets = <&rcc STM32F4_APB2_RESET(DSI)>;
> +			reset-names = "apb";
> +
> +			port {
> +				dsi_in: endpoint {
> +					remote-endpoint = <&ltdc_out_dsi>;
> +				};
> +			};
> +
> +			panel-dsi at 0 {
> +				reg = <0>; /* dsi virtual channel (0..3) */
> +				compatible = ...;
> +				enable-gpios = ...;
> +
> +			};
> +
> +		};
> +
> +	};
> +};
> 

Apart from that :
Reviewed-by: Neil Armstrong <narmstrong at baylibre.com>