[PATCH 3/4 DONOTMERGE] ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3

[Corentin Labbe]

From: Chen-Yu Tsai <wens at csie.org>

The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:

  - 2GB LPDDR3 DRAM
  - 8GB eMMC
  - Micro-SD card slot
  - HDMI output
  - Headset (stereo + mic) jack
  - Onboard mic
  - Gigabit Ethernet with RTL8211E transceiver
  - Ampak AP6212 WiFi + BT
  - USB OTG connector
  - USB-to-SATA bridge connected through a USB 2.0 hub
  - Consumer IR receiver
  - MIPI DSI LCD panel connector
  - Camera interface (parallel and MIPI CSI) connector
  - 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
  - Raspberry Pi 2 compatible GPIO header

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie at gmail.com>
---
 arch/arm/boot/dts/Makefile                   |  1 +
 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 94 ++++++++++++++++++++++++++++
 2 files changed, 95 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3bd29feb8298..4cb203deb118 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -897,6 +897,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a33-sinlinx-sina33.dtb \
 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
 	sun8i-a83t-cubietruck-plus.dtb \
+	sun8i-a83t-bananapi-m3.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
 	sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
new file mode 100644
index 000000000000..bb23904847d5
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -0,0 +1,94 @@
+/*
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens at csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a83t.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Banana Pi BPI-M3";
+	compatible = "sinovoip,bpi-m3", "allwinner,sun8i-a83t";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
-- 
2.13.0